E

Power Cord Set Requirements

3-Conductor Power Cord Set

The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC.

The power cord set included with the computer meets the requirements for use in the country where the equipment is purchased.

Power cord sets for use in other countries must meet the requirements of the country where the computer is used.

Maintenance and Service Guide E–1

Power Cord Set Requirements

General Requirements

The requirements listed below are applicable to all countries.

■ The length of the power cord set must be at least 1.5 m

(5.0 ft) and a maximum of 2.0 m (6.5 ft).

■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.

■ The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or 250 V AC, as required by each country’s power system.

■ The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.

E–2 Maintenance and Service Guide

Power Cord Set Requirements

Country-Specific Requirements

3-Conductor Power Cord Set Requirements

Country/Region

Australia

Austria

Belgium

Canada

Denmark

Finland

France

Germany

Accredited Agency

EANSW

OVE

CEBC

CSA

DEMKO

FIMKO

UTE

VDE

1

1

1

2

1

1

Applicable Note Number

1

1

Italy IMQ 1

Japan METI 3

✎

NOTES:

1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG,

3-conductor. The wall plug must be a two-pole grounding type with a

NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese

Industrial Standard C8303 (7 A, 125 V) configuration.

Maintenance and Service Guide E–3

Power Cord Set Requirements

3-Conductor Power Cord Set Requirements (Continued)

Country/Region

Korea

The Netherlands

Norway

People’s Republic of China

Sweden

Switzerland

Taiwan

Accredited Agency

EK

KEMA

NEMKO

CCC

SEMKO

SEV

BSMI

1

1

4

1

5

Applicable Note Number

4

1

United Kingdom BSI 1

United States UL 2

✎

NOTES:

1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG,

3-conductor. The wall plug must be a two-pole grounding type with a

NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.

3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese

Industrial Standard C8303 (7 A, 125 V) configuration.

4. The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size.

Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

5. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.

E–4 Maintenance and Service Guide