- Computers & electronics
- Computer components
- System components
- Server/workstation motherboards
- HP (Hewlett-Packard)
- PCI-9111DG/HR
- User's Guide
D/A Output Register. HP (Hewlett-Packard) NuDAQ PCI-9111HR, PCI-9111DG/HR
Add to My manuals83 Pages
advertisement
Bit 7 6 5 4 3 2 1
Base + 2h DI7 DI6 DI5 DI4 DI3 DI2 DI1
Base + 3h DI15 DI14 DI13 DI12 DI11 DI10 DI9
Address: BASE + 2h
0
DI0
DI8
Attribute: write only
Data Format:
Bit 7 6 5 4 3 2 1 0
Base + 2h DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
Base + 3h DO15 DO14 DO13 DO12 DO11 DO10 DO9 DO8
3.15 D/A Output Register
The D/A converter will convert the D/A output digital data to analog signal.
Address: BASE + 0
Attribute: write only
Data Format: (for D/A Channel 1)
Bit 7 6 5 4 3 2 1 0
Base + 0 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0
Base + 1 --- --- --- --- DA11 DA10 DA9 DA8
DA0 is the LSB and DA11 is the MSB of the 12 bits data.
---: don't care
3.16 Timer/Counter Register
Each 82C54 chip occupies 4 I/O address locations in the PCI-9111 as shown blow. Users can refer to 82C54 data sheet for the descriptions about all the features of 82C54. You can download the data sheet on the following web site:
“http://support.intel.com/support/controllers/peripheral/231164.htm” or “http://www.tundra.com/”
Address: BASE + 40h ~ BASE + 46h
Attribute: read / write
Data Format:
Base + 40h
Base + 42h
Counter 0 Register (R/W)
Counter 1 Register (R/W)
Base + 44h
Base + 46h
Counter 2 Register (R/W)
8254 CONTROL BYTE (W)
Registers Format • 21
advertisement
Related manuals
advertisement
Table of contents
- 11 Features
- 12 Applications
- 12 Specifications
- 14 Software Supporting
- 14 Programming Library
- 15 Driver
- 15 PCIS-VEE: HP-VEE Driver
- 15 : ActiveX Controls
- 15 driver
- 16 Driver
- 16 PCIS-OPC: OPC Server
- 17 What You Have
- 17 Unpacking
- 18 PCI-9111's Layout
- 19 Jumper Descriptions
- 19 Hardware Installation Outline
- 20 Device Installation for Windows Systems
- 20 Connectors Pin Assignment
- 22 Daughter Board Connection
- 22 Connect with ACLD
- 22 Connect with ACLD-9138 and ACLD
- 23 PCI PnP Registers
- 24 I/O Address Map
- 24 A/D Data Registers
- 25 A/D Channel Control Register
- 26 A/D Channel Read Back Register
- 26 A/D Input Signal Range Control Register
- 27 A/D Range and Status Readback Register
- 27 A/D Trigger Mode Control Register
- 28 Software Trigger Register
- 28 Interrupt Control Register
- 29 Hardware Interrupt Clear Register
- 29 A/D Mode & Interrupt Control Read Back Register
- 30 Extended I/O Ports
- 30 Digital I/O register
- 31 D/A Output Register
- 31 Timer/Counter Register
- 32 A/D Conversion
- 33 A/D Conversion Procedure
- 33 A/D Signal Source Control
- 35 A/D Trigger Source Control
- 36 A/D Data Transfer Modes
- 38 Pre-Trigger Control
- 40 A/D Data Format
- 41 Interrupt Control
- 41 System Architecture
- 41 IRQ Level Setting
- 41 Dual Interrupt System
- 42 Interrupt Source Control
- 42 Extended Digital I/O Port
- 43 D/A Conversion
- 44 Digital Input and Output
- 44 Timer/Counter Operation
- 44 Introduction
- 45 Pacer Trigger Source
- 45 Pre-Trigger Counter
- 45 I/O Address
- 46 Libraries Installation
- 47 Programming Guide
- 47 Naming Convention
- 47 Data Types
- 48 _9111_Initial
- 48 _9111_DO
- 49 _9111_DO_Channel
- 49 _9111_DI
- 50 _9111_DI_Channel
- 50 _9111_EDI
- 51 _9111_EDO
- 51 _9111_EDO_Read_Back
- 52 _9111_Set_EDO_Function
- 53 _9111_DA
- 53 _9111_AD_Read_Data
- 54 _9111_AD_Read_Data_Repeat
- 54 _9111_AD_Set_Channel
- 55 _9111_AD_Get_Channel
- 56 _9111_AD_Set_Range
- 57 _9111_AD_Get_Range
- 57 _9111_AD_Get_Status
- 58 _9111_AD_Set_Mode
- 59 _9111_AD_Get_Mode
- 59 _9111_INT_Set_Reg
- 60 _9111_INT_Get_Reg
- 60 _9111_Reset_FIFO
- 61 _9111_AD_Soft_Trigger
- 61 _9111_Set
- 62 _9111_Get
- 62 _9111_AD_Timer
- 63 _9111_Counter_Start
- 63 _9111_Counter_Read
- 64 _9111_Counter_Stop
- 65 _9111_INT_Source_Control
- 66 _9111_CLR_IRQ
- 66 _9111_Get_IRQ_Channel
- 67 _9111_Get_IRQ_Status
- 67 _9111_AD_FFHF_Polling
- 68 _9111_AD_Aquire
- 68 _9111_AD_HR_Aquire
- 69 _9111_AD_INT_Start
- 70 _9111_AD_FFHF_INT_Start
- 72 _9111_AD_INT_Status
- 72 _9111_AD_FFHF_INT_Status
- 73 _9111_AD_FFHF_INT_Restart
- 74 _9111_AD_INT_Stop
- 75 What do you need
- 76 VR Assignment
- 76 A/D Adjustment
- 77 D/A Adjustment
- 77 Unipolar Analog Output
- 77 Bipolar Analog Output
- 78 9111util
- 78 Running 9111util.exe
- 79 System Configuration
- 80 Calibration
- 81 Functional Testing
- 82 I_EEPROM