- Computers & electronics
- Computer components
- System components
- Server/workstation motherboards
- HP (Hewlett-Packard)
- PCI-9111DG/HR
- User's Guide
_9111_AD_INT_Status. HP (Hewlett-Packard) NuDAQ PCI-9111HR, PCI-9111DG/HR
Add to My manuals83 Pages
advertisement
5.41 _9111_AD_INT_Status
@ Description
This function is used to check the status of interrupt operation. The
_9111_AD_INT_Start() is executed on background, therefore you can issue this function to check the status of interrupt operation. While all the specified counts of data are acquired, the interrupt status will be changed to “AD_INT_STOP”.
@ Syntax
C/C++ (DOS)
U16 _9111_AD_INT_Status (U16 cardNo, U16 *status, U16 *count)
C/C++ (Windows 95)
U16 W_9111_AD_INT_Status (U16 cardNo, U16 *status, U16 *count)
Visual Basic (Windows 95)
W_9111_AD_INT_Status (ByVal cardNo As Integer, status As
Integer, count As Integer) As Integer
@ Argument cardNo: the card number of PCI-9111 card initialized. status: the status of the INT data transfer, the valid status code are the following:
AD_INT_RUN count:
AD_INT_STOP the A/D conversion count number performed currently
@ Return Code
ERR_NoError
5.42 _9111_AD_FFHF_INT_Status
@ Description
This function is used to check the status of interrupt operation using AD
FIFO Half Full Interrupt Transfer Mode. The _9111_AD_FFHF_INT_Start is executed on background, therefore you can issue this function to check the status of interrupt operation. While all the specified blocks of data are acquired, the interrupt status will be changed to
“AD_FFHF_BLOCK_FULL”.
@ Syntax
C/C++ (DOS)
U16 _9111_AD_FFHF_INT_Status (U16 cardNo, U16 *status, U16
*blockNo)
62 • C/C++ Library
advertisement
Related manuals
advertisement
Table of contents
- 11 Features
- 12 Applications
- 12 Specifications
- 14 Software Supporting
- 14 Programming Library
- 15 Driver
- 15 PCIS-VEE: HP-VEE Driver
- 15 : ActiveX Controls
- 15 driver
- 16 Driver
- 16 PCIS-OPC: OPC Server
- 17 What You Have
- 17 Unpacking
- 18 PCI-9111's Layout
- 19 Jumper Descriptions
- 19 Hardware Installation Outline
- 20 Device Installation for Windows Systems
- 20 Connectors Pin Assignment
- 22 Daughter Board Connection
- 22 Connect with ACLD
- 22 Connect with ACLD-9138 and ACLD
- 23 PCI PnP Registers
- 24 I/O Address Map
- 24 A/D Data Registers
- 25 A/D Channel Control Register
- 26 A/D Channel Read Back Register
- 26 A/D Input Signal Range Control Register
- 27 A/D Range and Status Readback Register
- 27 A/D Trigger Mode Control Register
- 28 Software Trigger Register
- 28 Interrupt Control Register
- 29 Hardware Interrupt Clear Register
- 29 A/D Mode & Interrupt Control Read Back Register
- 30 Extended I/O Ports
- 30 Digital I/O register
- 31 D/A Output Register
- 31 Timer/Counter Register
- 32 A/D Conversion
- 33 A/D Conversion Procedure
- 33 A/D Signal Source Control
- 35 A/D Trigger Source Control
- 36 A/D Data Transfer Modes
- 38 Pre-Trigger Control
- 40 A/D Data Format
- 41 Interrupt Control
- 41 System Architecture
- 41 IRQ Level Setting
- 41 Dual Interrupt System
- 42 Interrupt Source Control
- 42 Extended Digital I/O Port
- 43 D/A Conversion
- 44 Digital Input and Output
- 44 Timer/Counter Operation
- 44 Introduction
- 45 Pacer Trigger Source
- 45 Pre-Trigger Counter
- 45 I/O Address
- 46 Libraries Installation
- 47 Programming Guide
- 47 Naming Convention
- 47 Data Types
- 48 _9111_Initial
- 48 _9111_DO
- 49 _9111_DO_Channel
- 49 _9111_DI
- 50 _9111_DI_Channel
- 50 _9111_EDI
- 51 _9111_EDO
- 51 _9111_EDO_Read_Back
- 52 _9111_Set_EDO_Function
- 53 _9111_DA
- 53 _9111_AD_Read_Data
- 54 _9111_AD_Read_Data_Repeat
- 54 _9111_AD_Set_Channel
- 55 _9111_AD_Get_Channel
- 56 _9111_AD_Set_Range
- 57 _9111_AD_Get_Range
- 57 _9111_AD_Get_Status
- 58 _9111_AD_Set_Mode
- 59 _9111_AD_Get_Mode
- 59 _9111_INT_Set_Reg
- 60 _9111_INT_Get_Reg
- 60 _9111_Reset_FIFO
- 61 _9111_AD_Soft_Trigger
- 61 _9111_Set
- 62 _9111_Get
- 62 _9111_AD_Timer
- 63 _9111_Counter_Start
- 63 _9111_Counter_Read
- 64 _9111_Counter_Stop
- 65 _9111_INT_Source_Control
- 66 _9111_CLR_IRQ
- 66 _9111_Get_IRQ_Channel
- 67 _9111_Get_IRQ_Status
- 67 _9111_AD_FFHF_Polling
- 68 _9111_AD_Aquire
- 68 _9111_AD_HR_Aquire
- 69 _9111_AD_INT_Start
- 70 _9111_AD_FFHF_INT_Start
- 72 _9111_AD_INT_Status
- 72 _9111_AD_FFHF_INT_Status
- 73 _9111_AD_FFHF_INT_Restart
- 74 _9111_AD_INT_Stop
- 75 What do you need
- 76 VR Assignment
- 76 A/D Adjustment
- 77 D/A Adjustment
- 77 Unipolar Analog Output
- 77 Bipolar Analog Output
- 78 9111util
- 78 Running 9111util.exe
- 79 System Configuration
- 80 Calibration
- 81 Functional Testing
- 82 I_EEPROM