Speed Dialing. Samsung SCH-N391

Add to My manuals
76 Pages

advertisement

Speed Dialing. Samsung SCH-N391 | Manualzz

ettttiin Stta

Low Battery Indicator

You can easily tell if your battery needs to be recharged by checking the Battery Status icon ( ) at the upper-right corner of your phone’s display. The presence of all three bars indicates a full charge, two bars indicates a smaller charge, and one bar indicates an even smaller charge.

When the battery charge level becomes low, the battery sensor blinks an empty Battery Status icon

( ) and sounds a warning tone. If the battery level becomes too low, the phone automatically turns off.

When this happens, you lose whatever you are doing and your phone call cuts off. Watch the Battery Status icon and make sure that your battery is adequately charged.

20

Switching the Phone On or Off

1. Press and hold the key until the power-on image displays to switch the phone on.

The service light on the phone flashes and an alert sounds. When the system locates services, the greeting message displays along with the date and time. You can now place and receive calls.

If the phone is out of service, the No Service icon

( ) appears on the display. In this case, you cannot make and receive calls. You can try again later when service is available.

ettttiin g S

2. When you wish to switch the phone off, hold the key down more than two seconds.

WARNING!

Do not switch the phone on when mobile phone use is prohibited or when it may cause interference or danger.

Note: As with any other radio-transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects the call quality and may cause the phone to operate at a higher power level than otherwise needed.

Your Phone’s Modes

Standby Mode

Standby is the most basic state of your phone. The phone goes into Standby mode after you turn it on or whenever you briefly press the key. When your phone is in Standby mode, you will typically see the greeting message and the current date and time. If you enter a phone number, you can press the key to dial it or press the OK key to save it in the internal

Phonebook.

Press the key at any time to return to Standby mode. Be careful; if you are on a call when you press the key, the call disconnects and the phone returns to Standby mode.

21

ettttiin Stta

Talk Mode

You can place and answer calls only when your phone is turned on. During a call, the phone is in Talk mode.

While you are in Talk mode, pressing the MENU key gives you a list of options. See page 36 for details.

Power Save Mode

Your phone comes with a Power Save feature that is automatically activated if your phone is unable to find a signal after 15 minutes of searching. While this feature is active, the phone’s battery charge is conserved. The phone automatically rechecks for a signal periodically. To manually force the phone to recheck for a signal, press any key.

Lock Mode

When you lock your phone using the Lock Phone menu (MENU 9-8-1), you cannot use the phone. In

Lock mode, you can receive messages and calls, but you cannot place an outgoing call until you unlock the phone. To unlock the phone, you need to enter the lock code.

For details about locking and unlocking your phone, see page 111.

Silent Mode

Silent mode disables all of the sounds on the phone.

This feature is best used in situations where the phone might disturb others, such as in a meeting, at a library or in a theater. You can switch your phone to Silent mode with one touch of a key.

22 ettttiin g S

In Standby mode, press and hold until “Entering

Silent Mode” and the Vibration indicator ( ) display.

To exit and reactivate the previous sound settings, press and hold again until “Exiting Silent Mode” appears. The Vibration indicator no longer displays.

Locking or Unlocking the Keypad

You can make the keypad lock manually by pressing and holding in standy mode. You can prevent accidental key pressing with this key guard mode.

To lock the keypad automatically, use the Auto Key

Lock menu(Menu-9-3). See page 111.

To unlock your keypad, press and then .

Note: When the alram or schedular occurs or the call is received, the Key Lock mode is disabled.

23

advertisement

Related manuals