- Computers & electronics
- Computer components
- System components
- Audio cards
- AJA
- KONA LH/LHe
- User manual
advertisement
Chapter 3: Installation & Configuration
Installation Overview
The installation and set up of a KONA LHe is very simple. All of the steps of installation and configuration are documented in this chapter, summarized as follows:
1. Unpack the shipping box
2. If not previously installed on your Mac Pro, ensure that Final Cut Pro is installed as detailed in its user documentation. Final Cut Pro must be installed and have been run at least once prior to installing AJA KONA LHe software.
3. For Mac Pro and LHe:
Visit: http://www.aja.com/support/kona/kona-system-configuration.php
Locate your Mac model and install in the recommended slot.
For Model LHe and a G5:
Lay the PCIe PowerMac G5 on it’s on it’s side (motherboard facing up). Install the KONA
LHe capture card into one of the PCI Express slots in the PowerMac. The RAID controller card (SCSI or Fibre Channel) can go in any other available slot.
4. Install AJA KONA LHe software on your Mac from the supplied AJA CD-ROM
5. Cable the system audio and video sources, VTR, audio monitor, and video monitor. If you purchased the optional KL-box, then install it into an equipment rack or place it on a desk and connect its two cables to the KONA LHe card. If you’re instead using the standard cable set, then use those to connect equipment.
Each of these steps are explained in greater detail in the remaining pages of this chapter.
Unpacking
Shipping Box
Contents
KONA LHe is shipped with a CD containing system software and an Installation and User manual (a PDF on the CD), and a cable. If you purchased the optional KL-box breakout box, it ships with its own set of cables and instructions for connection to the KONA LHe card.
3
1 1
18
AJA KONA LH or
LHe Card
(KONA LH shown)
Installation Software CD
Read Me First Notice and Registration Sheets
Installation and Operation Manual in electronic form on the CD (PDF)
Standard Cable
KONA LH Breakout Cable
Contents, KONA LHe Shipping Box
As you unpack the shipping box(es), carefully examine the contents. Ensure you received everything and that nothing was damaged during shipment. If you find any damage, immediately notify the shipping service and supply them with a complete description of the damage. AJA will repair or replace damaged items. If you find shipping damage, contact your AJA dealer or distributor for details on how to have your KONA LHe repaired or replaced.
Note: Save packing materials and the shipping box. If you ever require service or move your system—use the packaging materials and box for safe shipment.
advertisement
Related manuals
advertisement
Table of contents
- 7 Table of Contents
- 7 Overview
- 7 Features
- 8 KONA LHe Audio
- 8 Software
- 8 What’s In The Box?
- 10 System Requirements
- 10 Minimum and Recommended System and Software Requirements
- 11 Understanding Disk Storage Methods
- 11 About RAIDs
- 12 Software For Striping
- 12 Storage capacity
- 13 Cable Connections
- 13 Using the Breakout Cable and 3 BNCs
- 13 Using KL-box
- 14 About BNC Connectors
- 14 Connector Descriptions—Cables and KL-box
- 14 SDI Input and Outputs
- 15 2 Channel Digital AES/EBU Audio Inputs And Outputs
- 15 Analog 2 Channel Balanced Audio
- 15 Analog 2 Channel Unbalanced Audio (KL-box only)
- 15 RS422 Machine Control
- 15 Analog Monitor Out (Component/Composite HD/SD)
- 15 Reference Video
- 16 In This Manual
- 17 Chapter 2: Getting Started—WorkflowKONA LHe And Your Workflow
- 18 Understanding Typical Workflows
- 18 PhotoJPEG
- 18 DV (DV25)
- 18 DVCPRO HD
- 20 Apple ProRes 422 and Apple ProRes 422 HQ (SD or HD)
- 20 Uncompressed 8-bit
- 20 Uncompressed 10-bit
- 21 Mixing and Matching Formats in Final Cut
- 23 Installation Overview
- 23 Unpacking
- 23 Shipping Box Contents
- 25 Installing the KONA LHe Card in a Mac Pro
- 26 Installing the KONA LHe Card in a G
- 27 Cabling the System
- 27 System Video/Audio Cable Connections
- 27 System Cabling When Using The Breakout Cable
- 28 Typical System
- 29 Installing KONA LHe Software
- 29 Software Installation Procedure
- 33 Genlock and Your System
- 35 Final Cut Pro
- 35 Using The KONA LHe Control Panel
- 35 Control Panel Basics
- 39 Control Tab Screen
- 39 Control Tab Screen Settings
- 41 Formats Tab Screen
- 42 Format Screen Settings
- 43 Input Select Tab Screen
- 43 Input Screen Settings
- 44 Proc Amp Screen
- 45 SDI Output Screen
- 45 SDI Output Screen Settings
- 46 Analog Out Screen
- 46 Analog Out Screen Settings
- 47 Video Setup Screen
- 47 Setup Screen Settings
- 48 Audio Setup Screen
- 48 Audio Setup Screen Settings
- 49 Conversion Tab Screen
- 49 Conversion Tab Screen Settings
- 51 DS Keyer Screen
- 51 DS Keyer Screen Settings
- 52 Timecode Screen
- 52 Timecode Screen Settings
- 53 Timelapse Tab Screen
- 54 Info Screen
- 55 Saving Your Control Panel Presets
- 55 Who is Controlling KONA LHe?
- 56 QuickTime Application—1st Priority
- 56 Mac Desktop Video—2nd Priority
- 57 KONA Control Panel—3rd Priority
- 57 Control Recommendations
- 58 Using Multiple AJA Products
- 58 Notes on using multiple AJA Products
- 59 Easy Setups for Typical Uses
- 59 Easy Setups Menu
- 61 Easy Setups For Use With KONA LHe
- 61 Audio/Video Settings Menu
- 62 To Create A New Easy Setup
- 63 The Sequence Presets Window
- 69 Checking the System with a Simple Test Project of Bars and Tone
- 72 Using 8-bit Versus 10-bit Video
- 73 If You Run Into Problems
- 74 Updating Software
- 74 Support
- 75 Apple Resources