advertisement
e. The appliance must always be activated paying attention that there are no obstacles for air suction and output.
f. Do not use the appliance in places used as laundry rooms.
g. The appliance must only be installed in dry places.
h. The cooler must not be started in presence of dangerous materials, steams or liquids.
i. Clean the air filters at least once a week.
2.3 - ELECTRICAL CONNECTION
The appliance is fitted with a power cable with plug.
Before connecting the cooler ensure that:
• The voltage and power frequency values match those specified on the appliance plate data.
• The power line is equipped with an ef fective earth connection and is correctly sized for maximum power consumption of the cooler.
3 - USE OF THE APPLIANCE
The appliance operating modes can be selected either using the remote control supplied or the control panel.
The reception of the selected function is confirmed by the emission of a
“beep” by the buzzer.
EN - 12
PELER TOWER
3.1 - CONTROL PANEL AND REMOTE CONTROL (Fig.1)
1 A2 A7
A5
A3
A4
A6
B2 B3 B4 B5 z z h c
A1
B10
B1
A1
A6
A2
B6 B7 B8 B9
A1.
ON / OFF key
A2.
Cooler/Humidifier and ionizing function key
A3.
Air speed key
A4.
Timer key
A5.
Appliance rotation key
A6.
Mode key
A7.
Cooler/Humidifier and ionizing function key
A8.
Display
EN - 13
B1.
Room temperature detected (°C)
B2.
“Normal” mode LED
B3.
“Natural” mode LED
B4.
“Rest” mode LED
B5.
Cooling/Humidifier LED
B6.
Low speed LED
B7.
Medium speed LED
B8.
High speed LED
B9.
“Ionizing” function mode LED
B10.
Timer set (h)
A3
A5
A4
A8
3.2 - USE OF THE REMOTE CONTROL
The remote control supplied with the appliance is the instrument that will allow you to use the appliance in the most comfortable way possible.
It should be handled with care and in particular:
• Keep it dry (do not clean it with water or leave it outdoors in bad weather).
• Avoid dropping or bumping it.
• Keep it out of direct sunlight.
• The remote control operates by means of an infrared beam.
• Avoid obstacles between the remote control and the appliance during use.
• If other appliances in the room have remote controls (TV, stereo, etc...), there may be interference.
• Electronic and fluorescent lights may interfere with the transmissions between remote control and appliance.
• Remove the batteries in case of prolonged disuse of the remote control.
3.2.a - Introduction of the battery (fig. E - F)
The power supply battery is included.
The battery is already installed in the remote control. Replace it, if necessary: a . Press the tab (14a) and extract the battery support (14b).
b . Insert the DL2025 type battery into the support with the “+” sign at the top.
c . Re-position the battery support (14b) in the remote control.
Scrupulously respect the polarities.
3.2.b - Replacement of the battery
The battery must be replaced when you no longer hear a beep from the appliance when pressing any key on the remote control.
EN - 14
PELER TOWER
Always use new batteries.
The use of old batteries could generate malfunctioning of the remote control.
Once discharged, the battery must be replaced and eliminated in the relevant collection centres or as envisioned by local regulations.
• If the remote control is not used for several weeks or longer, remove the battery.
Any leaks from the battery could damage the remote control.
Do not re-charge or disassemble the battery. Do not throw the battery into the fire.
It could burn or explode.
If the battery liquid falls onto the skin or clothes, wash well with clean water. Do not use the remote control with batteries that have leaked.
The chemical products contained in the batteries can cause burns or other risks to health.
3.2.c - Location of the remote control
Keep the remote control in a position from which the signal can reach the receiver of the appliance (maximum distance is approx. 6 metres - with charged batteries) (figure D).
The presence of obstacles (furniture, curtains, walls, etc.) between the remote control and the appliance reduces the remote control range.
3.3 - USE OF THE APPLIANCE
Work as follows in order to use the appliance.
EN - 15
3.3.a - Preliminary operations
• Place the appliance on a stable and not inclined base, at least 15 cm. from the wall or from any other object, in order to ensure the correct air circulation. Place it on a water-resistant surface since the possible water leakage could damage furniture or the floor.
• Do not place the appliance directly on carpets, towels, blankets or other absorbent surfaces.
• Insert the plug in the power socket; the appliance beeps and the display shows room temperature in °C.
Before electrically connecting the appliance, make sure the plate data correspond to those of the electricity distribution network.
3.3.b - Filling (fig. G)
It is necessary to add water in the tank before the cooling/humidifier function is activated.
Water can be added by opening the reservoir door (6).
Make sure that the cap (fig. A - pos.15) is positioned correctly.
- Pour water into the compartment.
- Check the water level in the tank through the water level gauge (7)
(fig.L).
- Close the door (6) again.
• Do not fill the tank beyond the maximum indicated level.
• Always use clean water.
• The appliance could produce a slight smell or the water in the tank could be slightly coloured during first use; this events are normal and absolutely harmless for the user’s health.
EN - 16
PELER TOWER
3.4 - INSTRUCTIONS FOR OPERATION a.
Insert the plug in the power socket.
When the appliance is switched on for the first time, you will hear a beep and it will go into stand-by. All buttons will be disabled, with the exception of the ON/OFF one.
The functions can be enabled or modified either from the control panel or from the remote control.
b.
Press th ON/OFF key (A1) to switch the appliance on (a beep is heard).
c.
ON/OFF key (A1) again to switch the appliance off (a beeeep is heard).
A beep is heard every time a key is pressed.
d.
Manually lift the horizontal flaps as desired.
3.4.a - ON/OFF key (A1)
When the appliance is in stand-by, all buttons are disabled, with the exception of the ON/OFF button.
Press the ON/OFF button to turn the appliance on. The display will show room temperature in °C.
The default initial fan speed is “low” and the default operating mode is “normal”; the relative LEDs (B2 and B6) will light up. All functions are available.
3.4.b - Air speed key (A3)
Air speed can be changed according to this sequence:
Low ---> Medium ---> High ---> Low ---> ...
- According to the set speed, the display will show the relative LED.
LED B6 (Low)
LED B7 ( Medium )
LED B8 ( High )
EN - 17
3.4.c - Appliance rotation key (A5)
With the appliance running, by pressing the key (A5), the appliance body starts to swing.
By pressing the key again, the function switches off.
3.4.d - Mode key (A6)
When the appliance is switched on, “normal” mode is set by default.
Press this key and the mode changes according to this sequence:
Normal ---> Natural ---> Sleep (sleeping) ---> Normal ---> Natural ---> ...
The mode LED changes accordingly (the “natural” (B2) and “sleep” (B3) modes are not available at “silent” speed (B4)).
The various modes work as follows:
1 Normal (B2): the appliance works constantly at the set speed.
2 Natural (B3): the appliance works changing air speed continuously.
3 Sleep (B4): the appliance works changing air speed continuously, reducing it down to the minimum value.
3.4.e - Timer key (A4)
When the appliance is on, press this key and the timer changes according to this sequence:
0h (off) ---> 1h ---> 2h ---> 3h ---> .. 12h ---> 0h (off) ---> ..
3.4.f Cooler/humidifier key
• When the appliance is on, to start the cooling/humidification function:
- press the “A2” key on the appliance command panel once or press the
“A2” key on the remote control. LED “B5” switches on.
• To switch the function off:
- press the “A2” key on the appliance command panel three times or press the “A2” key on the remote control once. LED “B5” switches off.
EN - 18
PELER TOWER
Do not allow the pump (4) to operate without water in the reservoir in order to prevent damage to the same.
3.4.g - “Ionizing” function key
• When the appliance is on, to start the ionizing function:
- press the “A7” key on the appliance command panel twice or press the
“A7” key on the remote control. LED “B9” switches on.
• To switch the function off:
- press the “A7” key on the appliance command panel twice or press the
“A7” key on the remote control once. LED “B9” switches off.
The two “cooling/humidification” and “ionizing” functions can be used together by pressing the “A2” and “A7” keys on the remote control or by pressing the “A2/A7” key on the command panel three times. Both LEDs “B5” and “B9” must be on.
3.4.i - Use of ice box containers (16)
The appliance comes with two ice boxes (16) that can be used to cool down the air it emits.
The use of the “cooling” function with an ice box (16) placed in the water com partment quickly reduces the temperature of the air emitted by the appliance by
3° C approximately.
To use this function: a.
Put the ice boxes in the freezer and wait until they are frozen.
b.
Place a frozen ice box in the water reservoir or in the upper water compart ment (fig.M).
c.
Pour water (preferably cold) into the reservoir without exceeding the “ MAX ” level indicated.
d.
Start the appliance and select the function by pressing the relevant key; the
LED (B5) must be on.
To exploit the function as well as possible, keep an ice box in the freezer and use it to replace the one in use when no longer frozen.
EN - 19
advertisement