advertisement
Settings
Temperature format
– °C
(Factory default)
– °F
Showroom programme
This programme is for dealers who want to demonstrate the appliance without the heater elements working.
Do not activate this setting for domestic use!
– Off
(Factory default)
– Demo programme
Follow the prompts in the display to switch the demo programme on.
Factory default
– All settings
Any settings that you have altered will be reset to the factory default setting.
– Recommended temperatures
Only those recommended temperatures which have been changed will be reset to the factory default settings.
To switch the demo programme off
If you have switched on the demo programme inadvertently, follow the steps below to switch it off again:
^ Select " % Settings".
^ Select the "Showroom prog." option and confirm your selection with OK.
^
Select the "Off" option and confirm your selection with OK.
^ Touch the OK sensor for 4 seconds.
^
Confirm the closing prompt with OK.
45
advertisement
Related manuals
advertisement
Table of contents
- 12 H 5051 B, H 5061 B
- 13 Oven controls
- 13 Safety features
- 13 System lock
- 13 Safety switch-off
- 13 Cooling system
- 13 Vented oven door
- 14 Energy saving features
- 15 User instructions
- 15 Moisture plus
- 15 "Moisture plus" recipe booklet
- 15 PerfectClean treated surfaces
- 15 Catalytic enamelled surfaces
- 16 Energy efficiency rating according to EN
- 16 Accessories
- 16 Baking tray, universal tray and rack with non-tip notches
- 17 Anti-splash insert (depending on model)
- 17 Handle (depending on model)
- 17 Food probe
- 17 Descaling tablets, plastic tube with clip
- 18 Function selector
- 19 Temperature selector
- 19 Sensors
- 19 Keypad tone
- 20 Display
- 28 To select a function
- 28 Selecting a temperature
- 28 Recommended temperatures
- 28 To change the temperature
- 29 Heating-up phase
- 29 Pre-heating the oven
- 30 Entering the Duration, a Start time or Finish time
- 30 To enter the time
- 31 To use Automatic switch-off
- 31 Delaying the start with Automatic switch-off
- 32 Sequence of the cooking programme when using Automatic switch-off
- 32 Changing or deleting an entered cooking time
- 33 Activating moisture reduction
- 34 Automatic programmes
- 35 Number of bursts of steam and when they are injected
- 37 Evaporate residual moisture
- 37 The residual moisture evaporation process
- 37 To start the residual moisture evaporation process
- 38 To cancel the residual moisture evaporation process
- 38 Descaling
- 41 Display
- 41 Clock format
- 41 To set the time of day
- 42 Lighting
- 42 Catalyser
- 42 Cooling fan run-on
- 43 Heating phase
- 43 Recommended temperatures
- 43 Display
- 43 Contrast
- 43 Brightness
- 43 Volume
- 43 Buzzer tones
- 44 Keypad tone
- 44 Frequency
- 44 Safety
- 44 To switch off the safety lock for one cooking programme
- 45 Temperature format
- 45 Showroom programme
- 45 To switch the demo programme off
- 45 Factory default
- 46 Appliance front
- 47 Accessories
- 47 Baking tray, universal tray, anti-splash insert (if applicable)
- 47 Rack, runners
- 47 Food probe
- 47 Oven interior
- 48 Seal and inside of the oven door
- 49 PerfectClean
- 51 Catalytic enamel surfaces
- 52 To remove the oven door
- 53 To dismantle the oven door
- 56 To refit the door
- 57 To remove the runners
- 57 To remove the catalytic enamelled back panel and roof liner
- 57 Back panel
- 58 Roof liner
- 59 When to run the descaling programme
- 59 Descaling process (overview)
- 60 Preparation
- 69 Appliance dimensions and unit cut-out
- 70 Front dimensions