advertisement
![Catalytic enamel surfaces. Miele H 5061 B, H 5361 B, H 5461 B, H 5051 B | Manualzz Catalytic enamel surfaces. Miele H 5061 B, H 5361 B, H 5461 B, H 5051 B | Manualzz](http://s3.manualzz.com/store/data/059523987_1-aa70ef8a6cbc94a5a0c272ab17af3c88-360x466.png)
Cleaning and care
Catalytic enamel surfaces
The back panel and roof liner are coated with dark grey catalytic enamel.
Soiling from oil and fat is burnt off these surfaces when very high temperatures are used in the oven. The higher the temperature, the more effective the process.
^ Select Fan plus U .
^
Set the highest temperature setting.
Run the oven for approx. 1 hour. The length of time will depend on the level of soiling.
The timer can also be used to set the finish time.
The catalytic coating becomes ineffective through using
–
–
– abrasive cleaning agents, hard brushes or abrasive sponges, oven sprays.
Remove the catalytic back panel and roof liner from the oven before cleaning the PerfectClean oven surfaces with oven spray.
Note that deposits of spices, syrups and similar substances are not removed from the catalytic coating by this process. These should be removed by hand whilst still fresh, using a mild solution of hot water and washing-up liquid applied with a soft sponge or brush. Remove the panels from the oven to do this.
Soiling caused by oil and grease splashes are removed from catalytic coated surfaces when the oven is heated to a high temperature. To do this:
^ Take all accessories out of the oven.
^ Wipe large deposits of soiling from the oven interior and the inside of the door before starting the cleaning process to avoid them baking onto
PerfectClean surfaces and becoming impossible to remove.
If the catalytic coated panels are very heavily soiled with oil and grease, a film will develop on the oven surface during the cleaning process which can be wiped off with warm water and a little washing-up liquid once cool.
^
Finally, clean the PerfectClean surfaces and the inside of the door.
Any remaining soiling will gradually disappear with each subsequent use of the oven at high temperatures.
Should the catalytic coating on the back panel or roof liner become ineffective through improper use or heavy soiling, a replacement can be obtained from your Miele dealer or the Miele Spare Parts Department.
51
advertisement
Related manuals
advertisement
Table of contents
- 12 H 5051 B, H 5061 B
- 13 Oven controls
- 13 Safety features
- 13 System lock
- 13 Safety switch-off
- 13 Cooling system
- 13 Vented oven door
- 14 Energy saving features
- 15 User instructions
- 15 Moisture plus
- 15 "Moisture plus" recipe booklet
- 15 PerfectClean treated surfaces
- 15 Catalytic enamelled surfaces
- 16 Energy efficiency rating according to EN
- 16 Accessories
- 16 Baking tray, universal tray and rack with non-tip notches
- 17 Anti-splash insert (depending on model)
- 17 Handle (depending on model)
- 17 Food probe
- 17 Descaling tablets, plastic tube with clip
- 18 Function selector
- 19 Temperature selector
- 19 Sensors
- 19 Keypad tone
- 20 Display
- 28 To select a function
- 28 Selecting a temperature
- 28 Recommended temperatures
- 28 To change the temperature
- 29 Heating-up phase
- 29 Pre-heating the oven
- 30 Entering the Duration, a Start time or Finish time
- 30 To enter the time
- 31 To use Automatic switch-off
- 31 Delaying the start with Automatic switch-off
- 32 Sequence of the cooking programme when using Automatic switch-off
- 32 Changing or deleting an entered cooking time
- 33 Activating moisture reduction
- 34 Automatic programmes
- 35 Number of bursts of steam and when they are injected
- 37 Evaporate residual moisture
- 37 The residual moisture evaporation process
- 37 To start the residual moisture evaporation process
- 38 To cancel the residual moisture evaporation process
- 38 Descaling
- 41 Display
- 41 Clock format
- 41 To set the time of day
- 42 Lighting
- 42 Catalyser
- 42 Cooling fan run-on
- 43 Heating phase
- 43 Recommended temperatures
- 43 Display
- 43 Contrast
- 43 Brightness
- 43 Volume
- 43 Buzzer tones
- 44 Keypad tone
- 44 Frequency
- 44 Safety
- 44 To switch off the safety lock for one cooking programme
- 45 Temperature format
- 45 Showroom programme
- 45 To switch the demo programme off
- 45 Factory default
- 46 Appliance front
- 47 Accessories
- 47 Baking tray, universal tray, anti-splash insert (if applicable)
- 47 Rack, runners
- 47 Food probe
- 47 Oven interior
- 48 Seal and inside of the oven door
- 49 PerfectClean
- 51 Catalytic enamel surfaces
- 52 To remove the oven door
- 53 To dismantle the oven door
- 56 To refit the door
- 57 To remove the runners
- 57 To remove the catalytic enamelled back panel and roof liner
- 57 Back panel
- 58 Roof liner
- 59 When to run the descaling programme
- 59 Descaling process (overview)
- 60 Preparation
- 69 Appliance dimensions and unit cut-out
- 70 Front dimensions