2.7.4 Wiring a Relay Contact. Advantech EKI-7710G-2CI, EKI-7710E-2C, EKI-7710G-2CPI, EKI-7710G-2CP
Add to My manuals156 Pages
advertisement
Electromagnetic Interference (EMI) affects the transmission performance of a device.
By properly grounding the device to earth ground through a drain wire, you can setup the best possible noise immunity and emissions.
Connection to
Grounding Point
Drain Wire with Lug
Figure 2.16 Grounding Connection
By connecting the ground terminal by drain wire to earth ground the switch and chassis can be ground.
Note!
Before applying power to the grounded switch, it is advisable to use a volt meter to ensure there is no voltage difference between the power supply’s negative output terminal and the grounding point on the switch.
2.7.4
Wiring a Relay Contact
The following section details the wiring of the relay output. The terminal block on the
EKI-7710 Series is wired and then installed onto the terminal receptor located on the
EKI-7710 Series.
V2+V2V1+V1DC12-48V
1A@24V
PWR2 P-Fail PWR1
Figure 2.17 Terminal Receptor: Relay Contact for Non PoE models
V2+V2V1+V1DC24-48V
1A@24V
PWR2 P-Fail PWR1
Figure 2.18 Terminal Receptor: Relay Contact for PoE models
The terminal receptor includes a total of six pins: two for PWR1, two for PWR2 and two for a fault circuit.
EKI-7710 Series User Manual 23
advertisement
Related manuals
advertisement
Table of contents
- 15 Supported Models
- 15 Specifications
- 17 Hardware Views
- 17 1.3.1 Front View
- 21 1.3.2 Rear View
- 22 1.3.3 Top View
- 24 Installation Guidelines
- 24 2.1.1 Connecting Hardware
- 24 Verifying Switch Operation
- 25 Installing the Switch
- 25 2.3.1 DIN Rail Mounting
- 26 2.3.2 Wall-Mounting
- 29 Installing and Removing SFP Modules
- 29 2.4.1 Installing SFP Modules
- 31 2.4.2 Removing SFP Modules
- 32 Connecting the Switch to Ethernet Ports
- 32 2.5.1 RJ45 Ethernet Cable Wiring
- 33 Connecting the Switch to Console Port
- 34 Power Supply Installation
- 34 2.7.1 Overview
- 34 2.7.2 Considerations
- 35 2.7.3 Grounding the Device
- 36 2.7.4 Wiring a Relay Contact
- 37 2.7.5 Wiring the Power Inputs
- 39 Reset Button
- 41 First Time Setup
- 41 3.1.1 Overview
- 41 3.1.2 Introduction
- 41 3.1.3 Administrative Interface Access
- 42 3.1.4 Using the Graphical (Web) Interface
- 42 3.1.5 Configuring the Switch for Network Access
- 43 3.1.6 Configuring the Ethernet Ports
- 43 Command Line Interface Configuration
- 43 3.2.1 Introduction to Command-Line Interface (CLI)
- 44 3.2.2 Accessing the CLI
- 44 Web Browser Configuration
- 44 3.3.1 Preparing for Web Configuration
- 44 3.3.2 System Login
- 47 Log In
- 47 Recommended Practices
- 47 4.2.1 Changing Default Password
- 48 Monitoring
- 48 4.3.1 Device Information
- 49 4.3.2 Logging Message
- 50 4.3.3 Port Monitoring
- 51 4.3.4 Link Aggregation
- 51 4.3.5 LLDP Statistics
- 52 4.3.6 IGMP Statistics
- 53 System
- 53 4.4.1 IP Settings
- 54 4.4.2 DHCP Client Option
- 55 4.4.3 DHCP Auto Provision
- 55 4.4.4 IPv6 Settings
- 56 4.4.5 Management VLAN
- 57 4.4.6 System Time
- 58 L2 Switching
- 58 4.5.1 Port Configuration
- 59 4.5.2 Port Mirror
- 59 4.5.3 Link Aggregation
- 62 4.5.4 802.1Q VLAN
- 66 4.5.5 Q-in-Q
- 67 4.5.6 GARP
- 68 4.5.7 802.3az EEE
- 69 4.5.8 Multicast
- 74 4.5.9 Jumbo Frame
- 74 4.5.10 Spanning Tree
- 79 4.5.11 X-Ring Elite
- 80 4.5.12 X-Ring Pro
- 81 4.5.13 Loopback Detection
- 82 MAC Address Table
- 82 4.6.1 Static MAC
- 83 4.6.2 MAC Aging Time
- 84 4.6.3 Dynamic Forwarding Table
- 84 Security
- 84 4.7.1 Storm Control
- 86 4.7.2 Port Security
- 87 4.7.3 Protected Ports
- 87 4.7.4 DoS Prevention
- 90 4.7.5 Applications
- 92 4.7.6 802.1x
- 93 4.7.7 IP Security
- 94 4.8.1 General
- 99 4.8.2 QoS Basic Mode
- 100 4.8.3 Rate Limit
- 102 Management
- 102 4.9.1 LLDP
- 106 4.9.2 SNMP
- 109 4.9.3 Power Over Ethernet
- 110 4.9.4 TCP Modbus
- 111 4.9.5 DHCP Server
- 115 4.9.6 SMTP Client
- 117 4.9.7 RMON
- 120 Diagnostics
- 120 4.10.1 Cable Diagnostics
- 121 4.10.2 Ping Test
- 122 4.10.3 IPv6 Ping Test
- 123 4.10.4 System Log
- 125 4.10.5 DDM
- 126 Tools
- 126 4.11.1 IXM
- 127 4.11.2 Backup Manager
- 128 4.11.3 Upgrade Manager
- 128 4.11.4 Dual Image
- 129 4.11.5 Save Configuration
- 129 4.11.6 User Account
- 130 4.11.7 Reset System
- 130 4.11.8 Reboot Device
- 130 Modbus/TCP Mapping
- 130 4.12.1 Modbus/TCP Mapping Table
- 155 Troubleshooting