MAC Address Table. Advantech EKI-7710G-2CI, EKI-7710E-2C, EKI-7710G-2CPI, EKI-7710G-2CP
Add to My manuals156 Pages
advertisement
The following table describes the items in the previous figure.
Item Description
State
Interval
Recover Time
Select
Enabled
or
Disabled
to setup the loopback mode.
Enter the variable in seconds (1 to 32767) to set the interval at which frames are transmitted.
Enter the variable in seconds (60 to 1000000) to define the delay before recovery.
Click
Apply
to save the values and update the screen.
Apply
The ensuing table for
Loopback Detection Global Information
settings are informational only: State, Interval and Recover Time.
4.5.13.2
Port Settings
The Port Settings page allows you to select ports that are detected by the loopback detection function and configure their status (enabled or disabled).
To access this page, click
L2 Switching
>
Loopback Detection
>
Port Settings
.
Figure 4.51 L2 Switching > Loopback Detection > Port Settings
The following table describes the items in the previous figure.
Item Description
Port Select
Enabled
Enter the port to define the local loopback detection setting.
Select
Enabled
or
Disabled
to setup the Loopback Detection function.
Click
Apply
to save the values and update the screen.
Apply
The ensuing table for
Loopback Detection Port Information
settings are informational only: Port, Enable State and Loop Status.
4.6
MAC Address Table
The MAC Address Table provides access to the Static MAC Settings, MAC Aging
Time, and Dynamic Forwarding.
4.6.1
Static MAC
The Static MAC page allows you to configure the address for forwarding of packets, the VLAN ID of the listed MAC address and the designated Port.
EKI-7710 Series User Manual 69
advertisement
Related manuals
advertisement
Table of contents
- 15 Supported Models
- 15 Specifications
- 17 Hardware Views
- 17 1.3.1 Front View
- 21 1.3.2 Rear View
- 22 1.3.3 Top View
- 24 Installation Guidelines
- 24 2.1.1 Connecting Hardware
- 24 Verifying Switch Operation
- 25 Installing the Switch
- 25 2.3.1 DIN Rail Mounting
- 26 2.3.2 Wall-Mounting
- 29 Installing and Removing SFP Modules
- 29 2.4.1 Installing SFP Modules
- 31 2.4.2 Removing SFP Modules
- 32 Connecting the Switch to Ethernet Ports
- 32 2.5.1 RJ45 Ethernet Cable Wiring
- 33 Connecting the Switch to Console Port
- 34 Power Supply Installation
- 34 2.7.1 Overview
- 34 2.7.2 Considerations
- 35 2.7.3 Grounding the Device
- 36 2.7.4 Wiring a Relay Contact
- 37 2.7.5 Wiring the Power Inputs
- 39 Reset Button
- 41 First Time Setup
- 41 3.1.1 Overview
- 41 3.1.2 Introduction
- 41 3.1.3 Administrative Interface Access
- 42 3.1.4 Using the Graphical (Web) Interface
- 42 3.1.5 Configuring the Switch for Network Access
- 43 3.1.6 Configuring the Ethernet Ports
- 43 Command Line Interface Configuration
- 43 3.2.1 Introduction to Command-Line Interface (CLI)
- 44 3.2.2 Accessing the CLI
- 44 Web Browser Configuration
- 44 3.3.1 Preparing for Web Configuration
- 44 3.3.2 System Login
- 47 Log In
- 47 Recommended Practices
- 47 4.2.1 Changing Default Password
- 48 Monitoring
- 48 4.3.1 Device Information
- 49 4.3.2 Logging Message
- 50 4.3.3 Port Monitoring
- 51 4.3.4 Link Aggregation
- 51 4.3.5 LLDP Statistics
- 52 4.3.6 IGMP Statistics
- 53 System
- 53 4.4.1 IP Settings
- 54 4.4.2 DHCP Client Option
- 55 4.4.3 DHCP Auto Provision
- 55 4.4.4 IPv6 Settings
- 56 4.4.5 Management VLAN
- 57 4.4.6 System Time
- 58 L2 Switching
- 58 4.5.1 Port Configuration
- 59 4.5.2 Port Mirror
- 59 4.5.3 Link Aggregation
- 62 4.5.4 802.1Q VLAN
- 66 4.5.5 Q-in-Q
- 67 4.5.6 GARP
- 68 4.5.7 802.3az EEE
- 69 4.5.8 Multicast
- 74 4.5.9 Jumbo Frame
- 74 4.5.10 Spanning Tree
- 79 4.5.11 X-Ring Elite
- 80 4.5.12 X-Ring Pro
- 81 4.5.13 Loopback Detection
- 82 MAC Address Table
- 82 4.6.1 Static MAC
- 83 4.6.2 MAC Aging Time
- 84 4.6.3 Dynamic Forwarding Table
- 84 Security
- 84 4.7.1 Storm Control
- 86 4.7.2 Port Security
- 87 4.7.3 Protected Ports
- 87 4.7.4 DoS Prevention
- 90 4.7.5 Applications
- 92 4.7.6 802.1x
- 93 4.7.7 IP Security
- 94 4.8.1 General
- 99 4.8.2 QoS Basic Mode
- 100 4.8.3 Rate Limit
- 102 Management
- 102 4.9.1 LLDP
- 106 4.9.2 SNMP
- 109 4.9.3 Power Over Ethernet
- 110 4.9.4 TCP Modbus
- 111 4.9.5 DHCP Server
- 115 4.9.6 SMTP Client
- 117 4.9.7 RMON
- 120 Diagnostics
- 120 4.10.1 Cable Diagnostics
- 121 4.10.2 Ping Test
- 122 4.10.3 IPv6 Ping Test
- 123 4.10.4 System Log
- 125 4.10.5 DDM
- 126 Tools
- 126 4.11.1 IXM
- 127 4.11.2 Backup Manager
- 128 4.11.3 Upgrade Manager
- 128 4.11.4 Dual Image
- 129 4.11.5 Save Configuration
- 129 4.11.6 User Account
- 130 4.11.7 Reset System
- 130 4.11.8 Reboot Device
- 130 Modbus/TCP Mapping
- 130 4.12.1 Modbus/TCP Mapping Table
- 155 Troubleshooting