First Time Setup. Advantech EKI-7710G-2CI, EKI-7710E-2C, EKI-7710G-2CPI, EKI-7710G-2CP
Add to My manuals156 Pages
advertisement
3.1
First Time Setup
3.1.1
Overview
The Industrial Ethernet Managed Switch is a configurable device that facilitates the interconnection of Ethernet devices on an Ethernet network. This includes computers, operator interfaces, I/O, controllers, RTUs, PLCs, other switches/hubs or any device that supports the standard IEEE 802.3 protocol.
This switch has all the capabilities of a store and forward Ethernet switch plus advanced management features such as SNMP, RSTP and port mirroring. This manual details how to configure the various management parameters in this easy to use switch.
3.1.2
Introduction
To take full advantage of all the features and resources available from the switch, it must be configured for your network.
The switch implements Rapid Spanning Tree Protocol (RSTP) and Simple Network
Management Protocol (SNMP) to provide most of the services offered by the switch.
Rapid Spanning Tree Protocol allows managed switches to communicate with each other to ensure that there exists only one active route between each pair of network nodes and provides automatic failover to the next available redundant route. A brief explanation of how RSTP works is given in the Spanning Tree section.
The switch is capable of communicating with other SNMP capable devices on the network to exchange management information. This statistical/derived information from the network is saved in the Management Information Base (MIB) of the switch.
The MIB is divided into several different information storage groups. These groups will be elaborated in detail in the Management and SNMP information section of this document. The switch implements Internet Group Management Protocol (IGMP) to optimize the flow of multicast traffic on your network.
The switch supports both port-based and tag-based Virtual LANs for flexible integration with VLAN-aware networks with support for VLAN-unaware devices.
3.1.3
Administrative Interface Access
There are several administrative interfaces to the switch:
1.
A graphical web interface accessible via the switch's built-in web server. Both
HTTP and secure HTTPS with SSL are supported.
Note!
This is the recommended method for managing the switch.
2.
A terminal interface via the RS232/USB port or over the network using telnet or
Secure Shell (SSH).
3.
An SNMP interface can be used to read/write many settings.
4.
Command Line Interface (CLI) can be used to read/write most settings. Initial setup must be done using an Ethernet connection (recommended) or the serial port.
28 EKI-7710 Series User Manual
advertisement
Related manuals
advertisement
Table of contents
- 15 Supported Models
- 15 Specifications
- 17 Hardware Views
- 17 1.3.1 Front View
- 21 1.3.2 Rear View
- 22 1.3.3 Top View
- 24 Installation Guidelines
- 24 2.1.1 Connecting Hardware
- 24 Verifying Switch Operation
- 25 Installing the Switch
- 25 2.3.1 DIN Rail Mounting
- 26 2.3.2 Wall-Mounting
- 29 Installing and Removing SFP Modules
- 29 2.4.1 Installing SFP Modules
- 31 2.4.2 Removing SFP Modules
- 32 Connecting the Switch to Ethernet Ports
- 32 2.5.1 RJ45 Ethernet Cable Wiring
- 33 Connecting the Switch to Console Port
- 34 Power Supply Installation
- 34 2.7.1 Overview
- 34 2.7.2 Considerations
- 35 2.7.3 Grounding the Device
- 36 2.7.4 Wiring a Relay Contact
- 37 2.7.5 Wiring the Power Inputs
- 39 Reset Button
- 41 First Time Setup
- 41 3.1.1 Overview
- 41 3.1.2 Introduction
- 41 3.1.3 Administrative Interface Access
- 42 3.1.4 Using the Graphical (Web) Interface
- 42 3.1.5 Configuring the Switch for Network Access
- 43 3.1.6 Configuring the Ethernet Ports
- 43 Command Line Interface Configuration
- 43 3.2.1 Introduction to Command-Line Interface (CLI)
- 44 3.2.2 Accessing the CLI
- 44 Web Browser Configuration
- 44 3.3.1 Preparing for Web Configuration
- 44 3.3.2 System Login
- 47 Log In
- 47 Recommended Practices
- 47 4.2.1 Changing Default Password
- 48 Monitoring
- 48 4.3.1 Device Information
- 49 4.3.2 Logging Message
- 50 4.3.3 Port Monitoring
- 51 4.3.4 Link Aggregation
- 51 4.3.5 LLDP Statistics
- 52 4.3.6 IGMP Statistics
- 53 System
- 53 4.4.1 IP Settings
- 54 4.4.2 DHCP Client Option
- 55 4.4.3 DHCP Auto Provision
- 55 4.4.4 IPv6 Settings
- 56 4.4.5 Management VLAN
- 57 4.4.6 System Time
- 58 L2 Switching
- 58 4.5.1 Port Configuration
- 59 4.5.2 Port Mirror
- 59 4.5.3 Link Aggregation
- 62 4.5.4 802.1Q VLAN
- 66 4.5.5 Q-in-Q
- 67 4.5.6 GARP
- 68 4.5.7 802.3az EEE
- 69 4.5.8 Multicast
- 74 4.5.9 Jumbo Frame
- 74 4.5.10 Spanning Tree
- 79 4.5.11 X-Ring Elite
- 80 4.5.12 X-Ring Pro
- 81 4.5.13 Loopback Detection
- 82 MAC Address Table
- 82 4.6.1 Static MAC
- 83 4.6.2 MAC Aging Time
- 84 4.6.3 Dynamic Forwarding Table
- 84 Security
- 84 4.7.1 Storm Control
- 86 4.7.2 Port Security
- 87 4.7.3 Protected Ports
- 87 4.7.4 DoS Prevention
- 90 4.7.5 Applications
- 92 4.7.6 802.1x
- 93 4.7.7 IP Security
- 94 4.8.1 General
- 99 4.8.2 QoS Basic Mode
- 100 4.8.3 Rate Limit
- 102 Management
- 102 4.9.1 LLDP
- 106 4.9.2 SNMP
- 109 4.9.3 Power Over Ethernet
- 110 4.9.4 TCP Modbus
- 111 4.9.5 DHCP Server
- 115 4.9.6 SMTP Client
- 117 4.9.7 RMON
- 120 Diagnostics
- 120 4.10.1 Cable Diagnostics
- 121 4.10.2 Ping Test
- 122 4.10.3 IPv6 Ping Test
- 123 4.10.4 System Log
- 125 4.10.5 DDM
- 126 Tools
- 126 4.11.1 IXM
- 127 4.11.2 Backup Manager
- 128 4.11.3 Upgrade Manager
- 128 4.11.4 Dual Image
- 129 4.11.5 Save Configuration
- 129 4.11.6 User Account
- 130 4.11.7 Reset System
- 130 4.11.8 Reboot Device
- 130 Modbus/TCP Mapping
- 130 4.12.1 Modbus/TCP Mapping Table
- 155 Troubleshooting