advertisement
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 05/16)
Lifting.&.Moving
The planer is equipped with four lifting bars that extend in order to lift and place the planer, as shown in
Figure.11
.
The rear wheels and front feet mount to the bottom of the machine. Therefore, the best time to assemble these components is while the machine is elevated safely by the forklift.
When. installing. rear. wheels. and. front. feet. in. Steps.
2–3,. machine. MUST. be. fully. supported. by. forklift.
to. prevent. machine. from. falling,. causing. serious.
crushing. injury. or. death.. If. machine. can. not. be.
sufficiently.supported.during.the.next.two.steps,.we.
recommend.temporarily.setting.machine.on..supports.
such.as.4.x.4.blocks.to.raise.it.off.the.ground.
HEAVY LIFT!
Straining or crushing injury may occur from improperly lifting machine or some of its parts. To reduce this risk, get help from other people and use a forklift (or other lifting equipment) rated for weight of this machine.
Lifting
Bar
(1 of 4)
To.lift.and.place.machine,.do.these.steps:
1..
Use forklift to lift machine off pallet (see
Figure.11
).
.
Tip:.
When positioning lift forks, place shop rags or cardboard between forks and cabinet stand to avoid scratching paint.
2..
While machine is elevated, install rear wheels using (2) M8-1.25 X 60 cap screws and (2) 8mm lock washers (see .Figure.12
).
Figure.11.
Lifting planer with forklift.
x 2
Rear Wheel
(1 of 2)
Figure.12.
Rear wheels installed with machine elevated by forklift.
3.
Install both front feet (see Figure.13
).
4.
Set machine down in suitable location.
Front Foot
(1 of 2)
Figure.13.
Front feet installed with machine elevated by forklift.
-17-
advertisement
Related manuals
advertisement
Table of contents
- 4 INTRODUCTION
- 4 Contact Info
- 4 Machine Differences
- 4 Manual Accuracy
- 5 Machine Specifications
- 7 Identification
- 8 Controls & Components
- 9 Internal Components
- 10 SAFETY
- 10 Standard Machinery Safety Instructions
- 12 Additional Safety for Planers
- 13 ELECTRICAL
- 13 Circuit Requirements
- 14 Grounding Requirements
- 14 Extension Cords
- 15 SETUP
- 15 Unpacking
- 15 Items Needed for Setup
- 16 Inventory
- 17 Cleaning Machine
- 18 Machine Placement
- 19 Lifting & Moving
- 20 Assembly
- 21 Dust Collection
- 22 Checking Gearbox Oil Level
- 23 Test Run
- 24 OPERATIONS
- 24 General
- 25 Workpiece Inspection
- 25 Wood Types
- 26 Planing Tips
- 26 Cutting Problems
- 28 Depth of Cut
- 29 Bed Roller Height
- 30 Setting Feed Rate
- 30 (W1742W & W1754W)
- 30 Adjusting/Replacing Knives
- 32 (W1742SW & W1754SW)
- 33 ACCESSORIES
- 33 Planer Accessories
- 34 MAINTENANCE
- 34 Schedule
- 34 Cleaning & Protecting
- 34 Lubrication
- 37 SERVICE
- 37 General
- 37 Tensioning/Replacing V-Belts
- 38 Tensioning Table Height Chain
- 39 Pressure Bar Heights
- 43 Adjusting Roller Spring Tension
- 44 Positioning Chip Deflector
- 45 Calibrating Table Height Scale
- 45 Anti-Kickback Fingers
- 46 Pulley Alignment
- 47 Troubleshooting
- 49 Electrical Safety Instructions
- 50 W1742W & W1742SW Wiring Diagram
- 51 W1754W & W1754SW Wiring Diagram
- 52 PARTS:.W1742W.&.W1742SW
- 52 Headstock
- 54 Table
- 56 Gearbox
- 57 Feed Gearing
- 58 Cabinet Stand
- 60 PARTS:.W1754W.&.W1754SW
- 60 Headstock
- 62 Table
- 64 Gearbox
- 65 Feed Gearing
- 66 Cabinet Stand
- 68 PARTS:.LABELS.&.COSMETICS
- 71 WARRANTY