advertisement
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 05/16)
Positioning.Chip.Deflector
Chip Deflector Gap Setting .................................
1 ⁄
4
"
When properly distanced from the cutterhead, the chip deflector directs the chips into the dust hood, and keeps them from falling onto the outfeed roller and being pressed into the workpiece.
Tools.Needed.
Qty
Phillips Screwdriver #2 .........................................1
Fine Ruler or Calipers ..........................................1
To.adjust.chip.deflector.gap,.do.these.steps:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove dust hood, top cover, and belt cover.
3.
Use cutterhead pulley to rotate cutterhead until a knife/insert reaches closest distance to chip deflector (see Figure.53
), then measure distance between knife/insert and chip deflector. The gap should be equal to 1 ⁄
4
".
—..
If distance measured in Step.3
is not equal to 1 ⁄
4
", then loosen flange screws that secure chip deflector and adjust gap to 1 ⁄
4
".
4.
Re-tighten flange screws, then replace belt cover, top cover, and dust hood.
Chip Deflector
Flange Screws
(1 of 3)
Figure.53.
Chip deflector and securing flange bolts.
-42-
advertisement
Related manuals
advertisement
Table of contents
- 4 INTRODUCTION
- 4 Contact Info
- 4 Machine Differences
- 4 Manual Accuracy
- 5 Machine Specifications
- 7 Identification
- 8 Controls & Components
- 9 Internal Components
- 10 SAFETY
- 10 Standard Machinery Safety Instructions
- 12 Additional Safety for Planers
- 13 ELECTRICAL
- 13 Circuit Requirements
- 14 Grounding Requirements
- 14 Extension Cords
- 15 SETUP
- 15 Unpacking
- 15 Items Needed for Setup
- 16 Inventory
- 17 Cleaning Machine
- 18 Machine Placement
- 19 Lifting & Moving
- 20 Assembly
- 21 Dust Collection
- 22 Checking Gearbox Oil Level
- 23 Test Run
- 24 OPERATIONS
- 24 General
- 25 Workpiece Inspection
- 25 Wood Types
- 26 Planing Tips
- 26 Cutting Problems
- 28 Depth of Cut
- 29 Bed Roller Height
- 30 Setting Feed Rate
- 30 (W1742W & W1754W)
- 30 Adjusting/Replacing Knives
- 32 (W1742SW & W1754SW)
- 33 ACCESSORIES
- 33 Planer Accessories
- 34 MAINTENANCE
- 34 Schedule
- 34 Cleaning & Protecting
- 34 Lubrication
- 37 SERVICE
- 37 General
- 37 Tensioning/Replacing V-Belts
- 38 Tensioning Table Height Chain
- 39 Pressure Bar Heights
- 43 Adjusting Roller Spring Tension
- 44 Positioning Chip Deflector
- 45 Calibrating Table Height Scale
- 45 Anti-Kickback Fingers
- 46 Pulley Alignment
- 47 Troubleshooting
- 49 Electrical Safety Instructions
- 50 W1742W & W1742SW Wiring Diagram
- 51 W1754W & W1754SW Wiring Diagram
- 52 PARTS:.W1742W.&.W1742SW
- 52 Headstock
- 54 Table
- 56 Gearbox
- 57 Feed Gearing
- 58 Cabinet Stand
- 60 PARTS:.W1754W.&.W1754SW
- 60 Headstock
- 62 Table
- 64 Gearbox
- 65 Feed Gearing
- 66 Cabinet Stand
- 68 PARTS:.LABELS.&.COSMETICS
- 71 WARRANTY