advertisement
326
325
301
302
327
333
REF PART # DESCRIPTION
301 X1742W301 GEARBOX
302 X1742W302 OIL SEAL 25 X 40 X 7
303 X1742W303 BALL BEARING 6204ZZ
304 X1742W304 GEAR 15T
305 X1742W305 CAP SCREW M6-1 X 25 LH
306 X1742W306 FENDER WASHER 6MM
307 X1742W307 FLANGE BOLT M6-1 X 12
308 X1742W308 BALL BEARING 6201ZZ
309 X1742W309 GEAR 47T
310 X1742W310 GEARED SHAFT 18T
311 X1742W311 KEY 5 X 5 X 12
312 X1742W312 GEAR 71T
313 X1742W313 KEY 5 X 5 X 10
314 X1742W314 COMBO GEAR 22T/18T
315 X1742W315 O-RING 11.8 X 2.65
316 X1742W316 FLAT WASHER 6MM
317 X1742W317 COMBO GEAR 92T/96T
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 05/16)
308
Gearbox
309
311
307
306
303
308
304
319
A
310
332
313
305
312
308
308
314
A
B
303
C
328
D
320
323
318
321
324
C
334
317
322
330
315
308
329
307
332
316
REF PART # DESCRIPTION
318 X1742W318 GEARBOX COVER GASKET
319 X1742W319 GEARBOX COVER
320 X1742W320 KEY 5 X 5 X 40
321 X1742W321 STEEL BALL 6MM
322 X1742W322 COMPRESSION SPRING 0.5 X 5 X 20.2
323 X1742W323 SHAFT
324 X1742W324 OIL SEAL 25 X 47 X 7
325 X1742W325 LOCK WASHER 8MM
326 X1742W326 CAP SCREW M8-1.25 X 45
327 X1742W327 DRAIN PLUG M12-1.25 X 16
328 X1742W328 CAP SCREW M6-1 X 25
329 X1742W329 SHIFTING FORK
330 X1742W330 SHIFTING SHAFT
332 X1742W332 LOCK WASHER 6MM
333 X1742W333 O-RING 9 X 1.8
334 X1742W334 ROLL PIN 5 X 25
-54-
advertisement
Related manuals
advertisement
Table of contents
- 4 INTRODUCTION
- 4 Contact Info
- 4 Machine Differences
- 4 Manual Accuracy
- 5 Machine Specifications
- 7 Identification
- 8 Controls & Components
- 9 Internal Components
- 10 SAFETY
- 10 Standard Machinery Safety Instructions
- 12 Additional Safety for Planers
- 13 ELECTRICAL
- 13 Circuit Requirements
- 14 Grounding Requirements
- 14 Extension Cords
- 15 SETUP
- 15 Unpacking
- 15 Items Needed for Setup
- 16 Inventory
- 17 Cleaning Machine
- 18 Machine Placement
- 19 Lifting & Moving
- 20 Assembly
- 21 Dust Collection
- 22 Checking Gearbox Oil Level
- 23 Test Run
- 24 OPERATIONS
- 24 General
- 25 Workpiece Inspection
- 25 Wood Types
- 26 Planing Tips
- 26 Cutting Problems
- 28 Depth of Cut
- 29 Bed Roller Height
- 30 Setting Feed Rate
- 30 (W1742W & W1754W)
- 30 Adjusting/Replacing Knives
- 32 (W1742SW & W1754SW)
- 33 ACCESSORIES
- 33 Planer Accessories
- 34 MAINTENANCE
- 34 Schedule
- 34 Cleaning & Protecting
- 34 Lubrication
- 37 SERVICE
- 37 General
- 37 Tensioning/Replacing V-Belts
- 38 Tensioning Table Height Chain
- 39 Pressure Bar Heights
- 43 Adjusting Roller Spring Tension
- 44 Positioning Chip Deflector
- 45 Calibrating Table Height Scale
- 45 Anti-Kickback Fingers
- 46 Pulley Alignment
- 47 Troubleshooting
- 49 Electrical Safety Instructions
- 50 W1742W & W1742SW Wiring Diagram
- 51 W1754W & W1754SW Wiring Diagram
- 52 PARTS:.W1742W.&.W1742SW
- 52 Headstock
- 54 Table
- 56 Gearbox
- 57 Feed Gearing
- 58 Cabinet Stand
- 60 PARTS:.W1754W.&.W1754SW
- 60 Headstock
- 62 Table
- 64 Gearbox
- 65 Feed Gearing
- 66 Cabinet Stand
- 68 PARTS:.LABELS.&.COSMETICS
- 71 WARRANTY