advertisement
![Tensioning Table Height Chain. Woodstock W1742W | Manualzz Tensioning Table Height Chain. Woodstock W1742W | Manualzz](http://s3.manualzz.com/store/data/063851537_1-b22a250a5d9dfe0df59abea28854d75e-360x466.png)
W1742W, W1742SW, W1754W, W1754SW (Mfd. Since 05/16)
3.
Remove front cabinet cover to access motor, as shown in Figure.40
.
4.
If V-belts need to be replaced, raise motor to release belt tension (see next step for instructions), roll them off pulleys, then replace with a matched set of three belts.
5.
To adjust V-belt tension, loosen both top motor mount hex nuts (see Figure.40
), then adjust bottom hex nuts to raise or lower motor.
Note:.
V-belts are correctly tensioned when there is approximately 3 ⁄
4
" of deflection when moderate pressure is applied to them midway between pulleys, as illustrated in Figure 41 .
6.
After V-belts are correctly tensioned, tighten top motor mount hex nuts, then re-install cabinet cover and belt cover.
Motor Mount
Hex Nuts
Figure.40.
Front cabinet cover removed to access motor.
Approximately
3⁄4" Deflection
Cutterhead
Pulley
Tensioning.Table.Height.
Chain
The table height chain transfers movement from the elevation handwheel to the columns that control table height. The chain drive can be adjusted to remove slack if the chain stretches over time or is loosened during table leveling procedures.
Tools.Needed.
Qty
Phillips Screwdriver #2 .........................................1
Hex Wrench 6mm ...............................................1
To.adjust.table.height.chain.tension,.do.these.steps:
1.
DISCONNECT MACHINE FROM POWER!
2.
Remove front and rear cabinet covers to access table height to chain (see Figure.42
).
3.
Loosen cap screws, then push idler sprocket against chain with moderate pressure. While maintaining pressure on idler sprocket, re-tighten cap screws
(see Figure.42
).
4.
Clean and lubricate chain and sprockets (refer to
Table.Height.Chain.&.Sprockets.
on Page.34
for detailed instructions), then re-install front and rear cabinet covers.
Motor
Pulley
Figure.41.
Belt deflection when V-belts are correctly tensioned.
Idler
Sprocket
Cap Screws
Figure.42.
Table height chain adjustment
(shown without stand for purpose of illustration).
DO. NOT. let. chain. fall. off. sprockets.. It.
can. be. very. difficult. to. return. chain.
to. its. proper. location. on. sprockets.
without.changing.table.adjustments.
-36-
advertisement
Related manuals
advertisement
Table of contents
- 4 INTRODUCTION
- 4 Contact Info
- 4 Machine Differences
- 4 Manual Accuracy
- 5 Machine Specifications
- 7 Identification
- 8 Controls & Components
- 9 Internal Components
- 10 SAFETY
- 10 Standard Machinery Safety Instructions
- 12 Additional Safety for Planers
- 13 ELECTRICAL
- 13 Circuit Requirements
- 14 Grounding Requirements
- 14 Extension Cords
- 15 SETUP
- 15 Unpacking
- 15 Items Needed for Setup
- 16 Inventory
- 17 Cleaning Machine
- 18 Machine Placement
- 19 Lifting & Moving
- 20 Assembly
- 21 Dust Collection
- 22 Checking Gearbox Oil Level
- 23 Test Run
- 24 OPERATIONS
- 24 General
- 25 Workpiece Inspection
- 25 Wood Types
- 26 Planing Tips
- 26 Cutting Problems
- 28 Depth of Cut
- 29 Bed Roller Height
- 30 Setting Feed Rate
- 30 (W1742W & W1754W)
- 30 Adjusting/Replacing Knives
- 32 (W1742SW & W1754SW)
- 33 ACCESSORIES
- 33 Planer Accessories
- 34 MAINTENANCE
- 34 Schedule
- 34 Cleaning & Protecting
- 34 Lubrication
- 37 SERVICE
- 37 General
- 37 Tensioning/Replacing V-Belts
- 38 Tensioning Table Height Chain
- 39 Pressure Bar Heights
- 43 Adjusting Roller Spring Tension
- 44 Positioning Chip Deflector
- 45 Calibrating Table Height Scale
- 45 Anti-Kickback Fingers
- 46 Pulley Alignment
- 47 Troubleshooting
- 49 Electrical Safety Instructions
- 50 W1742W & W1742SW Wiring Diagram
- 51 W1754W & W1754SW Wiring Diagram
- 52 PARTS:.W1742W.&.W1742SW
- 52 Headstock
- 54 Table
- 56 Gearbox
- 57 Feed Gearing
- 58 Cabinet Stand
- 60 PARTS:.W1754W.&.W1754SW
- 60 Headstock
- 62 Table
- 64 Gearbox
- 65 Feed Gearing
- 66 Cabinet Stand
- 68 PARTS:.LABELS.&.COSMETICS
- 71 WARRANTY