advertisement
![17.8.4 Selecting Temp Module. Mindray VS9 Operator's Manual | Manualzz 17.8.4 Selecting Temp Module. Mindray VS9 Operator's Manual | Manualzz](http://s1.manualzz.com/store/data/067700425_1-0a7a5f7ca753834b1ab9c639289712cc-360x466.png)
2.
Select the Module tab → CO2 tab.
3.
From the bottom left corner of the dialog select Zero .
17.8.3
Hiding the Invalid Display after Zeroing the CO
2
Module
After the zero calibration is completed, the CO
2
module reacquires the CO
2
readings.
During the reacquisition period, “ Zero Recovering ” is displayed in the CO
2
numeric area. Valid data will reappear 30 seconds after the zero calibration is started.
To hide the display of the “ Zero Recovering ” message, follow this procedure:
1.
Select the Main Menu quick key → from the System column select Maintenance
→ input the required password → select .
2.
Select the Module tab
→
CO2 tab.
3.
Switch off Zero Recovery For 30s .
Selecting Defaults from the bottom of the dialog can restore this setting to the factory default.
17.8.4
Selecting Temp Module
To select the type of Temp module of the monitor, follow this procedure:
1.
Select the Main Menu quick key → from the System column select Maintenance
→ input the required password → select .
2.
Select the Module tab
→
Temp tab.
3.
Select the Temp module based on the configuration of the monitor.
17.8.5
Setting Temp Measurement Sites
You can set the measurement sites based on the Temp type of the monitor. To do so, follow this procedure:
1.
Select the Main Menu quick key → from the System column select Maintenance
→ input the required password → select .
2.
Select the Module tab
→
Temp tab.
3.
Select the measurement sites as needed.
17.8.6
Adding a New Manual Parameter
If you need to add custom manual parameters to the Manual Input list, follow this procedure:
1.
Select the Main Menu quick key → from the System column select Maintenance
→ input the required password → select .
2.
Select Module
→
Manual Input tab, and then select Add .
3.
Select Name and input the name of the new parameter with the on-screen keyboard.
VS 9 Vital Signs Monitor Operator’s Manual
17 - 17
advertisement
Related manuals
advertisement
Table of contents
- 153 17 Password-protected User Settings
- 153 17.1 Setting the Device Location
- 153 17.1.1 Setting Monitor Information
- 153 17.1.2 Setting Monitor Location
- 153 17.1.3 Enabling the Auto Obtain Bed Number Function
- 154 17.2 Changing Patient Management Settings
- 154 17.2.1 Selecting Displayed Patient Information
- 154 17.2.2 Selecting Query Criteria for Searching Patients in ADT Server
- 155 17.2.3 Auto Discharging a Patient after Monitor Power Off
- 155 17.2.4 Auto Deleting Patient Data after Discharging a Patient
- 155 17.2.5 Clearing All Patient Data
- 156 17.2.6 Setting Patient Location Options for the Standby Screen
- 156 17.3 Changing the Authorization Settings
- 156 17.3.1 Setting Clinician Login
- 156 17.3.2 Selecting Password for User Maintenance
- 157 17.3.3 Selecting Password for Changing Alarm settings
- 157 17.3.4 Selecting Password for Viewing Discharged Patient Data
- 158 17.4 Changing Settings about Saving and Sending Data
- 158 17.4.1 Setting Items about Saving Data
- 159 17.4.2 Setting Items about Sending Data
- 160 17.5 Changing the Alarm Settings
- 160 17.5.1 Setting Alarm Tone Properties
- 161 17.5.2 Setting Alarm Pausing and Resetting Properties
- 163 17.5.3 Latching Physiological Alarms
- 163 17.5.4 Selecting Alarms to be Sent to the Nurse Call System
- 164 17.5.5 Changing Alarm Priority Settings
- 165 17.5.6 Setting the Alarm Delay Time
- 166 17.6 Changing the Standby Settings
- 166 17.6.1 Setting Prompt Message on Standby Screen
- 166 17.6.2 Setting Auto Standby
- 166 17.6.3 Enabling Black Standby Screen
- 167 17.7 Changing CAA Settings
- 167 17.7.1 Selecting the Default Scoring Tool
- 167 17.7.2 Managing the Scoring Tools
- 167 17.7.3 Setting GCS Threshold for Each Consciousness Level
- 168 17.8 Changing Module Settings
- 168 17.8.1 Selecting NIBP Measurement Algorithm
- 168 Module
- 169 17.8.4 Selecting Temp Module
- 169 17.8.5 Setting Temp Measurement Sites
- 169 17.8.6 Adding a New Manual Parameter
- 170 17.8.7 Managing Pain Score
- 171 17.8.8 Setting Parameter Measurement Timeout
- 171 17.8.9 Enabling Outline Font for Suspected Values
- 171 17.9 Setting Parameter Units
- 208 21.3 Temp Accessories
- 208 21.3.1 SmarTemp Temp Probes Available for Purchase
- 208 21.3.2 SmarTemp Temp Probe Wells Available for Purchase
- 208 21.3.3 SmarTemp Probe Covers Available for Purchase
- 208 21.3.4 Exergen Temp Probe Available for Purchase
- 209 Accessories
- 209 Accessory Available for Purchase
- 209 Accessories Also Compatible