![](http://s1.manualzz.com/store/data/004229910_1-492389d67a924fc062aee9373cef609b-128x128.png)
advertisement
![Operating and Installation Manual | Manualzz Operating and Installation Manual | Manualzz](http://s1.manualzz.com/store/data/004229910_1-492389d67a924fc062aee9373cef609b-360x466.png)
Proceeding
1. The time recorder is switched on.
" R" and "E" simultaneously and keep these keys pressed for 1 second.
→ Column pointer moves to the park position right of the card funnel.
3. Press the locking straps on the left and right side of the card funnel slightly towards the recorder and swing out the programming panel.
4. Lift up and remove the ribbon cassette.
Warning!
Depending on use, the printer head may be very hot.
Touching the printer head could cause burns.
5. Insert new ribbon cassette and push slightly down.
Tighten the new ribbon by winding the red ribbon tightening knob in the direction indicated by the arrow on the cassette. Position the free guide of the ribbon in the direction of the printer head.
Make sure that the ribbon guide is inserted in front of the printer head and that the ribbon is not twisted or creased.
The ribbon cassette must engage into the left and right locking straps.
6. Check that the ribbon fits between the printer head and the ribbon guide.
Tighten the ribbon again.
7. Swing in the programming panel.
Press "R" and "E" once again, see step 2.
→ The column pointer moves back to initial position.
8. Close the time recorder.
Cleaning the Time Recorder
The main problem is dust on electronic components.
In order to maintain the physical appearance of the time recorder, the cover must be occasionally cleaned.
The cleaning intervals depend on the operating conditions and the location.
When cleaning the time recorder with cloths, please observe the following recommendations:
• Use only rags moistened with water or a soap-free detergent.
• Do not use any detergent spray or wet rags.
• Use only soft detergents without solvents of any kind.
• Make sure to thoroughly dry all components after cleaning.
40 Cleaning the Time Recorder
advertisement
Related manuals
advertisement
Table of contents
- 1 PERFECT 2020
- 3 Impressum
- 5 Safety instructions
- 7 Table of Contents
- 8 Product Overview
- 9 Time Recorder Specifications
- 10 Contents
- 11 Selecting a Location
- 11 General Conditions
- 11 Specific Conditions for the Time Recorder
- 12 Time Recorder Installation
- 12 Installation for Table Operation
- 13 Wall Mounting
- 14 Open the Recorder
- 15 Close the Recorder
- 15 Remove the Metal Back Plate
- 16 Wall Mounting
- 16 Connect the Power Supply
- 18 Connect Optional Features
- 20 Getting Started
- 20 Switch on the Unit
- 21 Programming Panel
- 24 Setting the Time and Date
- 26 Showing or Setting the Time of the Internal Quartz Clock
- 27 Synchronizing the Analogue Clock
- 27 Setting the Date
- 28 Programming
- 28 Calling up the Programming Routine
- 29 Daylight Saving Time Change-over
- 31 Column Change Timing
- 33 Card Lift / Line Change timing
- 34 Ribbon Color Change
- 36 Signal Operation
- 38 Signal out-programming
- 39 Check of individuals (Option)
- 40 Punching at the Recorder
- 41 Punching with Standard Time Cards
- 41 Standby Operation (Option)
- 42 Change of Fuse for Signal Output
- 43 Error messages
- 44 Adjustment Routine
- 44 Card lift / Line change
- 44 Column change
- 45 Changing the Ribbon
- 46 Cleaning the Time Recorder
- 47 Technical Specifications
- 48 Local Sales and Service Dealer