Text message report. Lupus Electronics LUPUSEC-XT1

Text message report

In case of an active alarm, the LUPUSEC-XT1 is able to send a text message to an alarm center firm or to any private mobile phone.

Test message settings:

Enter the login data for your third-party provider. Currently the XT1 supports only

“smstrade.de”. Further providers will be supported in the future.

IMPORTANT LEGAL NOTICE:

Smstrade is a third-party provider. There are no legal or business relations between LUPUS-Electronics and smstrade. LUPUS-

Electronics does not assume any liability for the contents of the third-party website. LUPUS-Electronics does not check, control, or monitor the contents and services provided on the website, including the prices. LUPUS-Electronics does not assume any guarantee, warranty, or liability with regard to the services provided by third parties and their proper use in connection with the

LUPUSEC-XT1 as well as with regard to content, correctness, or legitimacy of the goods, services, and material provided by the third party and the third party website. The text message offers shown above are valid only at the time this manual was printed are may possibly not be up-to-date. The access to third party websites is made at your own risk. The use of third party websites and third party services is subject to the applicable terms and conditions of the respective third party provider, including the applicable privacy policies. You may use any other test message provider together with the LUPUSEC-XT1 at your own risk.

Please note that the time between sending and receiving a text message notification is subject to external technical conditions such as e.g. the mobile network utilization and may therefore vary greatly .



Service:



Enter the login data for your third-party provider. Currently the XT1 supports only “smstrade.de”. Further providers will be supported in the future.

43

Note:

To use the text message service, you need to set up an account free of charge on the website of www.smstrade.de.



Key:

Enter the key you assigned to you by smstrade.de (further explanations on the next pages).



Route:

U se only smstrade route “Gold” service, as the sender number does not change with “Gold”.

To use the text message service (via the internet), you need an account on the website of www.smstrade.de. The registration is free, but every sent text message is charged.

After you created your account, unlocked it via the confirmation e-mail and logged in, go to the top of the customer area and click “Interfaces”.

The following image including the important “Gateway Key” will be displayed:

44

Copy this Gateway Key into the field “Key” of the LUPUSEC-XT1:

The following is a table listing the most common response codes of Smstrade:

Response Description

10 Recipient number incorrect

20

30

31

40

50

60

70

71

80

Sender ID incorrect

Text message incorrect

Message type incorrect

Text route incorrect

Identification failed

Insufficient credit

Network not covered

Feature impossible

Delivery to SMS-C failed

Troubleshooting

Use correct format, e.g.

491701231231

Use a sender with a maximum of maximal 11 alphanumerical or 16 numerical characters

Use a maximum of 160 characters of text or parameter concat=1

Delete message type or use one of the following values: flash, unicode, binary, voice.

Available routes: basic, gold, direct

Check Gateway Key

Charge credit

Choose different route

Choose different route

Choose different route or contact support

100 Text received and sent

Text message gateway test

45



Recipient

Enter the mobile number to which you want to send a test text message.



Text:

Enter the text of the test message.

Report to alarm center (contact ID)

Recipient:

Enter the mobile or telephone number of the alarm center, which is then informed about every status message via Contact ID protocol. If the alarm center requires an

ID, enter the ID in front of the mobile number, followed by @, e.g.

1234@01791234567 an.

Refer to the end of this manual for the syntax of the Contact ID protocol.

Example of text message content: < 18340100014>

Recipient and message

Send in case of:



Alarm = Sends a text message only in case of an alarm



Status changes = Additionally sends a text message in case of arming/disarming



All events = Sends a text message whenever the status changes (not recommended)

Recipient:

Enter the mobile number to which you want to send a test text message. You can specify a maximum of two recipients.

Text:

Enter the text of the test message.

Note:

In most mobile phones like iPhone or Samsung Galaxy, you can set the ring tone for text messages, the volume as well as the number of repetitions of the alert sound to make sure that you do not miss any notification.

46