Put the smoke detector into operation. Lupus Electronics LUPUSEC-XT1
Add to My manuals130 Pages
Lupus Electronics LUPUSEC-XT1 is an advanced security system designed to protect your home or business. With its intuitive interface and wide range of features, the LUPUSEC-XT1 makes it easy to keep your property safe and secure.
Some of the key features of the LUPUSEC-XT1 include:
- Easy to use: The LUPUSEC-XT1 features a user-friendly interface that makes it easy to set up and operate.
- Remote access: You can arm and disarm your system, view live video, and receive alerts from anywhere with the LUPUSEC app.
- Expandable: The LUPUSEC-XT1 can be expanded to include a variety of sensors, detectors, and cameras, so you can customize your system to meet your specific needs.
advertisement
5.
Mounting bracket
6.
Attachment hook
Put the smoke detector into operation
1.
After you inserted the batteries, two brief signals sound. The LED starts flashing.
You have six minutes (warm-up phase) to add the smoke detector to the control unit.
2.
Open the configuration page of the control unit and start the login process in the
Sensors menu.
3.
Press the Test button at the smoke detector. Two brief signal tones sound.
4.
If the control unit detects the device, it emits a signal tone for confirmation.
5.
Now add the smoke detector to the control unit.
Note:
The calibration starts after the six minutes warm-up phase of the smoke detector.
A short beep sounds every 100 seconds during these six minutes. The calibration takes about 2 to 16 minutes and is completed at the end with two successful signals. If the calibration failed after 16 minutes, a constant beep will sound. In that case, remove the batteries and restart with step 1.
You cannot integrate the smoke detector during the calibration; this is possible only before or after the calibration process.
6.
Perform an optional range test.
For this purpose, open the menu Sensors Range and click on Start. Take the smoke detector to the place of installation and press the Test button of the smoke detector. The test menu of the control unit indicates the signal strength of the radio transmission. The higher the value the better the radio signal (1-9).
Mounting of smoke detector:
1. Use the bracket (5) as a template to drill the holes.
2. Mount the bracket so that the two hooks (6) face down.
3. Press the installation notches (4) onto the attachment hooks (6) and lock it with pressure and a clockwise turn, making sure that the line located at the side of the smoke detector is directly below one of the hooks.
In case of alarm:
If the smoke concentration exceeds the threshold, the detector will immediately report this to the XT1 and additionally emit a loud signal tone for ten seconds. If the smoke concentration measured after these ten seconds is still high, a signal tone is emitted again for ten seconds, until there is no more smoke in the measuring chamber. If you press the Test button in case of an alarm, the smoke detector will be deactivated for ten minutes. After these ten minutes, the smoke detector will sound two signal tones and return to its normal operating mode .
Place of installation of smoke detector:
Install the smoke detector always at the highest point and with minimum distance
84
of 60 cm to the wall.
Do not install the smoke detector in kitchens or bathrooms or other moist rooms to avoid false alarms and to increase the service life.
Do not install the smoke detector close to air conditioning systems or fans.
Cleaning:
Check the smoke detector regularly for proper function (TEST button) and clean it, if it is soiled.
In that case, carefully suction clean or blow clean it.
Do not use any liquids for cleaning.
Water must not enter the inside of the device.
Note:
In case of an alarm, the control unit and the smoke detector will alert. Additionally installed smoke detectors will not trigger alarms.
Even if the smoke detector has lost contact to the control unit (radio interference, control unit off, large distance), it will always react to smoke and alert you with its own siren!
Replace the smoke detector after ten years at the latest for your own safety.
85
advertisement
Key Features
- Easy to use interface
- Remote access with LUPUSEC app
- Expandable system with a variety of sensors and cameras
- Motion detection
- Door/window sensors
- Smoke and heat detectors
- Panic button
- Built-in siren
- Tamper protection
- Battery backup
Related manuals
Frequently Answers and Questions
How do I set up the LUPUSEC-XT1?
Can I add additional sensors or detectors to my LUPUSEC-XT1?
What is the range of the LUPUSEC-XT1's wireless sensors?
advertisement
Table of contents
- 4 Introduction
- 4 Disclaimer
- 6 Important safety information
- 6 If you detect defects
- 7 Intended use
- 8 Hardware description
- 9 Scope of delivery
- 10 Put the LUPUSEC-XT1 into operation
- 10 Control unit
- 10 Place of installation
- 11 Install the control unit
- 11 Connect the control unit
- 13 Access to the main interface of the LUPUSEC-XT
- 15 Menu description
- 15 Home menu
- 15 Overview
- 17 History
- 18 Captured events
- 19 Time frame
- 19 PIN codes
- 21 Control unit menu
- 21 Status
- 22 Settings
- 25 Siren
- 26 Date & Time
- 27 Sensors menu
- 28 Sensors settings
- 31 Range
- 31 Bypass
- 32 Devices
- 34 Wireless sockets (PSS)
- 35 Network menu
- 35 Settings
- 38 Cameras
- 40 Settings menu
- 40 Contact ID
- 41 Contact ID Syntax
- 42 Special codes
- 43 Text message report
- 47 E-mail
- 49 Upload
- 50 Automation
- 52 System menu
- 52 Admin
- 53 Firmware
- 53 Default settings
- 54 Log files
- 55 Remote access via the internet
- 57 Create Dynamic DNS account
- 62 Access via the LUPUSEC app (Android + iOS)
- 63 Profile list
- 64 Main menu
- 65 Navigation within the app
- 66 Mobile phone access via the mobile web interface
- 68 The user interface of the LUPUSEC-XT1 mobile app
- 71 Description of sensors and controls
- 72 XT Keypad
- 73 Put the keypad into operation
- 75 Window/door contact
- 76 Put the window/door contact into operation
- 77 Wireless indoor siren
- 77 Put the wireless indoor siren into operation
- 80 Wireless outdoor siren
- 80 Put the wireless outdoor siren into operation
- 83 Smoke detector
- 84 Put the smoke detector into operation
- 86 PIR motion detector
- 86 Put the PIR motion detector into operation
- 88 Water detector
- 88 Put the water detector into operation
- 89 Remote control
- 89 Put the remote control into operation
- 90 Medical emergency controller
- 90 Put the medical emergency controller into operation
- 91 Wireless sockets (PSS)
- 91 Put the wireless socket (with electric meter) into operation
- 92 Put the wireless socket (without electric meter) into operation
- 93 Glass breakage detector
- 93 Put the glass breakage detector into operation
- 95 PIR network camera
- 95 Put the PIR network camera into operation
- 98 Temperature sensor
- 98 Put the temperature sensor into operation
- 99 Wireless relay
- 99 Put the wireless relay into operation
- 101 Magnetic locking device
- 102 Install the magnetic locking device to the door and put it into operation
- 103 Mechanical locking device
- 104 Install the mechanical locking device to the door and put it into operation
- 106 Panic button
- 106 Put the panic button into operation
- 107 Wireless repeater
- 108 Connect the wireless repeater to the control unit
- 110 CO detector
- 110 Put the CO detector into operation
- 111 Heat detector
- 111 Put the heat detector into operation
- 113 Wireless sensor input
- 114 Put the wireless sensor input into operation
- 116 Wireless lock contact
- 116 Install the wireless lock contact to the door and put it into operation
- 118 In-wall relay with electric meter
- 118 Put the in-wall relay with electric meter into operation
- 119 In-wall relay without electric meter
- 119 Put the in-wall relay without electric meter into operation
- 121 Tag reader
- 122 Put the tag reader into operation
- 124 Two-way motion detector
- 126 Put the PIR/microwave motion detector into operation