DataBar Expanded Enable. Magellan 2300HS, 2200VS

DataBar Expanded Enable

Enables/disables the ability of the scanner to decode DataBar Expanded labels.

This value-added feature is a factory-programmed option. Contact your dealer for information about upgrading your system to include this advanced capability.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

DataBar Expanded = DISABLE

5-278

DataBar Expanded = ENABLE

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

DataBar Expanded Enable

DataBar Expanded EAN-128 Emulation

Enables/disables EAN-128 emulation for DataBar Expanded.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

DataBar Expanded/EAN-128 EMULATION = DISABLE

Product Reference Guide

DataBar Expanded/EAN-128 EMULATION = ENABLE

5-279

DataBar Expanded Label ID

This feature specifies an DataBar Expanded label ID to be added to bar code data.

The programming feature, Label ID Control, designates whether the

Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code, SET DataBar Expanded LABEL ID below. You’ll

need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired Label ID characters; entered as two hex pairs. A

table containing the ASCII Character Set and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

5-280

SET DataBar Expanded LABEL ID

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

DataBar Expanded Enable

DataBar Expanded Length Control

This feature specifies either variable-length or fixed-length decoding for

DataBar Expanded.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

You must now set the features DataBar Expanded Length 1

and

DataBar Expanded Length 2 .

NOTE

DataBar Expanded LENGTH CONTROL = VARIABLE-LENGTH

Product Reference Guide

DataBar Expanded LENGTH CONTROL = FIXED-LENGTH

5-281

DataBar Expanded Length 1

Length 1 is the minimum label length if in variable length mode, or the first fixed length if in fixed length mode (see

DataBar Expanded Length

Control )

. Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET DataBar Expanded LENGTH 1

below.

You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired label length. The selectable range for this option is

01 to 74. Pad all single digit numbers with a leading zero to yield a two-digit entry (01-74).

4. Complete the programming sequence by scanning the SWITCH bar code.

5-282

SET DataBar Expanded LENGTH 1

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

DataBar Expanded Enable

DataBar Expanded Length 2

Length 2 is the maximum label length if in variable length mode, or the

second fixed length if in fixed length mode (see DataBar Expanded

Length Control )

. Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET DataBar Expanded LENGTH 2

below.

You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired label length. A setting of 00 will ignore this length

(only one fixed length), otherwise, the selectable range for this option is 01 to 74. Pad all single digit numbers with a leading zero to yield a two-digit entry (01-74).

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET DataBar Expanded LENGTH 2

5-283

DataBar Expanded Minimum Reads

Specifies the minimum number of consecutive times an DataBar

Expanded label must be decoded before it is accepted as a good read.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

DataBar Expanded MINIMUM READS = 1

5-284

DataBar Expanded MINIMUM READS = 2

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

DataBar Expanded Enable

DataBar Expanded Minimum Reads — continued

Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

DataBar Expanded MINIMUM READS = 3

Product Reference Guide

DataBar Expanded MINIMUM READS = 4

5-285