advertisement
Standard 2 of 5 (Std 2 of 5) Enable
Enables/disables the ability of the scanner to decode Standard 2 of 5 labels.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH bar code.
STANDARD 2 OF 5 = DISABLE
5-328
STANDARD 2 OF 5 = ENABLE
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
Standard 2 of 5 (Std 2 of 5) Enable
Standard 2 of 5 Check Character Calculation
Enables/disables calculation and verification of an optional Standard 2 of
5 check character.
If check character calculation is disabled, the risk is increased that a misread can occur. When disabled, any check characters in a bar code are treated as data characters.
NOTE
To set this feature:
1. Scan the SWITCH bar code.
2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH bar code.
STANDARD 2 of 5 CHECK CHARACTER CALCULATION = DISABLE
Product Reference Guide
STANDARD 2 of 5 CHECK CHARACTER CALCULATION = ENABLE
5-329
Standard 2 of 5 Check Character Transmission
Enables/disables transmission of an optional Standard 2 of 5 check character.
This feature applies only when Standard 2 of 5 Check Character
is enabled.
NOTE
To set this feature:
1. Scan the SWITCH bar code.
2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH bar code.
STANDARD 2 of 5 CHECK CHARACTER TRANSMISSION = DISABLE
5-330
STANDARD 2 of 5 CHECK CHARACTER TRANSMISSION = ENABLE
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
Standard 2 of 5 (Std 2 of 5) Enable
Standard 2 of 5 Label ID
This feature specifies a Standard 2 of 5 label ID to be added to bar code data..
The programming feature, Label ID Control, designates whether the
Label ID is transmitted as a prefix or suffix or if Label ID is disabled.
NOTE
To set this feature:
1. Scan the SWITCH bar code.
2. Scan the bar code,
below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.
3. Scan the appropriate digits from the keypad in
resent the desired Label ID characters; entered as two hex pairs. A
table containing the ASCII Character Set and their corresponding
Hex Values is available in the inside back cover of this manual.
ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.
The selectable range for this option is any hex value from 00 to FF.
4. Complete the programming sequence by scanning the SWITCH bar code.
Product Reference Guide
SET STANDARD 2 of 5 LABEL ID
5-331
Standard 2 of 5 Length Control
This feature specifies whether variable-length or fixed-length decoding will be set for Standard 2 of 5.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH bar code.
You must now set
and
.
NOTE
STANDARD 2 OF 5 LENGTH CONTROL = VARIABLE-LENGTH
5-332
STANDARD 2 OF 5 LENGTH CONTROL = FIXED-LENGTH
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
Standard 2 of 5 (Std 2 of 5) Enable
Standard 2 of 5 Length 1
Length 1 is the minimum label length if in variable length mode, or the first fixed length if in fixed length mode (see
Standard 2 of 5 Length Control )
. Length includes the barcode’s check and data characters.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan the bar code,
below.
You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Scan the appropriate digits from the keypad in
resent the desired label length. The selectable range for this option is
01 to 50. Pad all single digit numbers with a leading zero to yield a two-digit entry (01-50).
4. Complete the programming sequence by scanning the SWITCH bar code.
Product Reference Guide
SET STANDARD 2 OF 5 LENGTH 1
5-333
Standard 2 of 5 Length 2
Length 2 is the maximum label length if in variable length mode, or the
second fixed length if in fixed length mode (see Standard 2 of 5 Length
. Length includes the barcode’s check and data characters.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan the bar code,
below.
You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Scan the appropriate digits from the keypad in
resent the desired label length. A setting of 00 will ignore this length
(only one fixed length), otherwise, the selectable range for this option is 01 to 50. Pad all single digit numbers with aleading zero to yield a two-digit entry (01-50).
4. Complete the programming sequence by scanning the SWITCH bar code.
5-334
SET STANDARD 2 OF 5 LENGTH 2
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
Standard 2 of 5 (Std 2 of 5) Enable
Standard 2 of 5 Correlation
This feature enables/disables character correlation for Standard 2 of 5.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Complete the programming sequence by scanning the SWITCH bar code.
STANDARD 2 of 5 CORRELATION = DISABLE
Product Reference Guide
STANDARD 2 of 5 CORRELATION = ENABLE
5-335
Standard 2 of 5 Stitching
Enables/disables stitching for Standard 2 of 5 labels. When parts of a Standard 2 of 5 bar code are presented to the scanner with this feature enabled, the bar code parts will be assembled by the scanner’s software, and the data will be decoded if all bar code proofing requirements are met.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
3. Complete the programming sequence by scanning the SWITCH bar code.
Standard 2 of 5 Stitching operates using fixed lengths ONLY. Standard
2 of 5 Length 1 and/or Standard 2 of 5 Length 2 must be properly con-
figured for stitching to work.
NOTE
I 2 OF 5 STITCHING = DISABLE
5-336
I 2 OF 5 STITCHING = ENABLE
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
Standard 2 of 5 (Std 2 of 5) Enable
Standard 2 of 5 Minimum Reads
Specifies the minimum number of consecutive times a Standard 2 of 5 label must be decoded before it is accepted as a good read.
To set this feature:
1. Scan the SWITCH bar code.
2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.
Complete the programming sequence by scanning the SWITCH bar code.
STANDARD 2 of 5 MINIMUM READS = 1
Product Reference Guide
STANDARD 2 of 5 MINIMUM READS = 2
5-337
Standard 2 of 5 Minimum Reads — continued
Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
STANDARD 2 of 5 MINIMUM READS = 3
5-338
STANDARD 2 of 5 MINIMUM READS = 4
Magellan
TM
2200VS/2200VS and 2300HS/2300HS
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project