Interleaved 2 of 5 (I 2 of 5) Enable. Magellan 2300HS, 2200VS

Interleaved 2 of 5 (I 2 of 5) Enable

Interleaved 2 of 5 (I 2 of 5) Enable

Enables/disables the ability of the scanner to decode Interleaved 2 of 5 labels.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 OF 5 = DISABLE

Product Reference Guide

I 2 OF 5 = ENABLE

5-317

I 2 of 5 Check Character Calculation

Enables/disables calculation and verification of an optional Interleaved 2 of 5 check character.

If check character calculation is disabled, the risk is increased that a misread can occur. When disabled, any check characters in a bar code are treated as data characters.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CHECK CHARACTER CALCULATION = DISABLE

5-318

I 2 of 5 CHECK CHARACTER CALCULATION = ENABLE

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Check Character Transmission

Enables/disables transmission of an optional Interleaved 2 of 5 check character.

This feature applies only when I 2 of 5 Check Character Calculation

is enabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CHECK CHARACTER TRANSMISSION = DISABLE

Product Reference Guide

I 2 of 5 CHECK CHARACTER TRANSMISSION = ENABLE

5-319

I 2 of 5 Label ID

This feature specifies an I 2 of 5 label ID to be added to bar code data..

The programming feature, Label ID Control, designates whether the

Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LABEL ID below. You’ll need to

cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired Label ID characters; entered as two hex pairs. A

table containing the ASCII Character Set and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

5-320

SET I 2 of 5 LABEL ID

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Length Control

This feature specifies whether variable-length or fixed-length decoding will be set for I 2 of 5.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

You must now set the features I 2 of 5 Length 1

and

I 2 of 5 Length

2

.

NOTE

I 2 OF 5 LENGTH CONTROL = VARIABLE-LENGTH

Product Reference Guide

I 2 OF 5 LENGTH CONTROL = FIXED-LENGTH

5-321

I 2 of 5 Length 1

Length 1 is the minimum label length if in variable length mode, or the first fixed length if in fixed length mode (see

I 2 of 5 Length Control )

.

Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LENGTH 1

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired label length. The selectable range for this option is

02 to 50, even numbers only. Pad all single digit numbers with a leading zero to yield a two-digit entry (02-50).

4. Complete the programming sequence by scanning the SWITCH bar code.

5-322

SET I 2 of 5 LENGTH 1

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Length 2

Length 2 is the maximum label length if in variable length mode, or the

second fixed length if in fixed length mode (see I 2 of 5 Length Control )

.

Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LENGTH 2

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that rep-

resent the desired label length. A setting of 00 will ignore this length

(only one fixed length), otherwise, the selectable range for this option is 02 to 50, even numbers only. Pad all single digit numbers with a leading zero to yield a two-digit entry (02-50).

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET I 2 of 5 LENGTH 2

5-323

I 2 of 5 Correlation

This feature enables/disables character correlation for I 2 of 5.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CORRELATION = DISABLE

5-324

I 2 of 5 CORRELATION = ENABLE

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Stitching

Enables/disables stitching for I 2 of 5 labels. When parts of an I 2 of 5 bar code are presented to the scanner with this feature enabled, the bar code parts will be assembled by the scanner’s software, and the data will be decoded if all bar code proofing requirements are met.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 Stitching operates using fixed lengths ONLY.

I 2 of 5 Length 1

and/or

I 2 of 5 Length 2

must be properly configured for stitching to work.

NOTE

I 2 OF 5 STITCHING = DISABLE

Product Reference Guide

I 2 OF 5 STITCHING = ENABLE

5-325

I 2 of 5 Minimum Reads

Specifies the minimum number of consecutive times an I 2 of 5 label must be decoded before it is accepted as a good read.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 MINIMUM READS = 1

5-326

I 2 of 5 MINIMUM READS = 2

Magellan

TM

2200VS/2200VS and 2300HS/2300HS

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Minimum Reads — continued

Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

I 2 of 5 MINIMUM READS = 3

Product Reference Guide

I 2 of 5 MINIMUM READS = 4

5-327