- Computers & electronics
- Computer components
- System components
- Processors
- Intel
- AT80571RG0601ML
- Data Sheet
<b>Boxed Processor Specifications</b>. Intel AT80571RG0601ML, AT80571RG0561ML
Add to My manuals100 Pages
advertisement
![<b>Boxed Processor Specifications</b>. Intel AT80571RG0601ML, AT80571RG0561ML | Manualzz <b>Boxed Processor Specifications</b>. Intel AT80571RG0601ML, AT80571RG0561ML | Manualzz](http://s1.manualzz.com/store/data/002641916_1-488dd57bc81289e14f221a02c423e2a1-360x466.png)
Boxed Processor Specifications
7 Boxed Processor Specifications
7.1
Introduction
The processor will also be offered as an Intel boxed processor. Intel boxed processors are intended for system integrators who build systems from baseboards and standard components. The boxed processor will be supplied with a cooling solution. This chapter documents baseboard and system requirements for the cooling solution that will be supplied with the boxed processor. This chapter is particularly important for OEMs that manufacture baseboards for system integrators.
Note: Unless otherwise noted, all figures in this chapter are dimensioned in millimeters and
inches [in brackets]. Figure 18
shows a mechanical representation of a boxed processor.
Note: Drawings in this section reflect only the specifications on the Intel boxed processor product. These dimensions should not be used as a generic keep-out zone for all cooling solutions. It is the system designers’ responsibility to consider their proprietary cooling solution when designing to the required keep-out zone on their system platforms and chassis. Refer to the appropriate Thermal and Mechanical Design
) for further guidance. Contact your local Intel Sales
Representative for this document.
Figure 18.
Mechanical Representation of the Boxed Processor
Datasheet
NOTE: The airflow of the fan heatsink is into the center and out of the sides of the fan heatsink.
91
advertisement
Key Features
- IntelĀ® CeleronĀ® E3200 2.4 GHz
- 1 MB L2 LGA 775 (Socket T)
- Processor cores: 2 45 nm 64-bit 65 W
Related manuals
advertisement
Table of contents
- 9 Introduction
- 9 Terminology
- 10 Processor Terminology Definitions
- 11 References
- 13 Electrical Specifications
- 13 Power and Ground Lands
- 13 Decoupling Guidelines
- 13 VCC Decoupling
- 13 VTT Decoupling
- 14 FSB Decoupling
- 14 Voltage Identification
- 16 Reserved, Unused, and TESTHI Signals
- 16 Power Segment Identifier (PSID)
- 17 Voltage and Current Specification
- 17 Absolute Maximum and Minimum Ratings
- 18 DC Voltage and Current Specification
- 20 VCC Overshoot
- 21 Die Voltage Validation
- 21 Signaling Specifications
- 22 FSB Signal Groups
- 23 CMOS and Open Drain Signals
- 24 Processor DC Specifications
- 25 Platform Environment Control Interface (PECI) DC Specifications
- 26 GTL+ Front Side Bus Specifications
- 27 Clock Specifications
- 27 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking
- 28 FSB Frequency Select Signals (BSEL[2:0])
- 29 Phase Lock Loop (PLL) and Filter
- 29 BCLK[1:0] Specifications
- 33 Package Mechanical Specifications
- 33 Package Mechanical Drawing
- 37 Processor Component Keep-Out Zones
- 37 Package Loading Specifications
- 37 Package Handling Guidelines
- 38 Package Insertion Specifications
- 38 Processor Mass Specification
- 38 Processor Materials
- 38 Processor Markings
- 39 Processor Land Coordinates
- 41 Land Listing and Signal Descriptions
- 41 Processor Land Assignments
- 64 Alphabetical Signals Reference
- 75 Thermal Specifications and Design Considerations
- 75 Processor Thermal Specifications
- 75 Thermal Specifications
- 78 Thermal Metrology
- 78 Processor Thermal Features
- 78 Thermal Monitor
- 80 On-Demand Mode
- 81 PROCHOT# Signal
- 81 THERMTRIP# Signal
- 82 Platform Environment Control Interface (PECI)
- 82 Introduction
- 82 TCONTROL and TCC activation on PECI-Based Systems
- 83 PECI Specifications
- 83 PECI Device Address
- 83 PECI Command Support
- 83 PECI Fault Handling Requirements
- 83 PECI GetTemp0() Error Code Support
- 85 Features
- 85 Power-On Configuration Options
- 85 Clock Control and Low Power States
- 86 Normal State
- 86 HALT and Extended HALT Powerdown States
- 86 HALT Powerdown State
- 87 Extended HALT Powerdown State
- 87 Stop Grant and Extended Stop Grant States
- 87 Stop-Grant State
- 88 Extended Stop Grant State
- 88 Stop Grant Snoop State, and Stop Grant Snoop State
- 88 HALT Snoop State, Stop Grant Snoop State
- 88 Extended HALT Snoop State, Extended Stop Grant Snoop State
- 88 Sleep State
- 89 Deep Sleep State
- 89 Deeper Sleep State
- 90 Technology
- 90 Processor Power Status Indicator (PSI) Signal
- 91 Boxed Processor Specifications
- 91 Introduction
- 92 Mechanical Specifications
- 92 Boxed Processor Cooling Solution Dimensions
- 93 Boxed Processor Fan Heatsink Weight
- 93 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly
- 93 Electrical Requirements
- 93 Fan Heatsink Power Supply
- 95 Thermal Specifications
- 95 Boxed Processor Cooling Requirements
- 97 Variable Speed Fan
- 99 Debug Tools Specifications
- 99 Logic Analyzer Interface (LAI)
- 99 Mechanical Considerations
- 99 Electrical Considerations