2.1.3 Injector Rear Panel. Planet POE-2400, POE-1200, POE-2400P4, POE-1200P2
Add to My manuals45 Pages
advertisement
2.1.3 Injector Rear Panel
The rear panel of the PoE Injector Hub indicates an AC inlet power socket, which accepts input power from 100 to 240V AC,
50/60Hz. Figure 2-6 & 2-7 shows rear panel of the PoE Injector Hub.
Figure 2-6
POE-1200 / POE-1200P2 Rear Panel
Figure 2-7
POE-2400 / POE-2400P4 Rear Panel
Power
Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your device from being damaged by unregulated surge or current to the PoE Injector Hub or the power adapter.
2.2 Installing the PoE Injector Hub
This section describes how to install your PoE Injector Hub and make connections to the PoE Injector Hub. Please read the following topics and perform the procedures in the order being presented. PLANET PoE Injector Hub do not need software configuration. To install the PoE Injector Hub on a desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install a PoE Injector Hub on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the PoE Injector Hub.
Step2: Place the PoE Injector Hub on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the PoE Injector Hub and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter
1, Section 5, in Specification.
Step4:
Connect your PoE Injector Hub to network 802.3af powered devices (PD) and Switch.
A. Connect one end of a standard network cable to the upper stack 10/100 RJ-45 ports on the front of the PoE
Injector Hub.
B. Connect the other end of the cable to the 802.3 powered devices (PD) such as IP phone, wireless access point,
IP camera, splitter, or switch…etc.
C. Connect the one end of a standard network cable to the relative lower stack 10/100 RJ-45 port on the front of the
PoE Injector Hub.
D. Connect the other end of the cable to the port of switch.
7
advertisement
Related manuals
advertisement
Table of contents
- 4 1. INTRODUCTION
- 8 2. INSTALLATION
- 8 2.1.1 Injector Front Panel
- 9 2.1.2 LED Indicators
- 10 2.1.3 Injector Rear Panel
- 10 2.2.1 Desktop Installation
- 11 2.2.2 Rack Mounting
- 12 2.2.3 Network Application Installation
- 13 2.2.4 Power over Ethernet Powered Device
- 14 3 MANAGEMENT
- 14 3.3.1 Web Management
- 16 3.3.2 PLANET Smart Discovery Utility
- 18 4 WEB CONFIGURATION
- 20 4.3.1 System Information
- 21 4.3.2 IP Configuration
- 22 4.3.3 Password Setting
- 26 4.5.1 Firmware Upgrade
- 28 4.5.2 Configuration Setting
- 30 4.5.3 Configuration Backup
- 34 4.5.4 Alert Trap Configuration
- 35 4.5.5 System Reboot
- 36 5. POWER OVER ETHERNET OVERVIEW
- 38 6. THE POE PROVISION PROCESS
- 40 7 TROUBLESHOOTING
- 41 APPENDIX A
- 43 APPENDIX B