Installation Available Ports
3.8
Available Ports
The OpenCom 100 has the following ports (see also Positions of the Ports starting on page 37):
3.8.1 OpenCom 130
The listed interfaces and ports are located on the basic module of the
OpenCom 130. Further interfaces and ports can be added by installing the
expansion set and additional interface cards (see Installing an Expansion Set
starting on page 26 and Installing Interface Cards starting on page 29).
■ One S
0
port to connect to an external S
0
bus (usually the NTBA), designed as an
RJ45 jack (S
0
1)
■ One switchable S
0
port (S
0
2), which can be connected as either an internal or external S
0
bus. The internal connection is via a pressure terminal and the external connection via an RJ45 jack.
■ Three U pn
ports, designed as pressure terminals (U pn
1 to U pn
3)
■ Four analogue a/b ports, designed as pressure terminals (a/b1 to a/b4)
■ One slot to incorporate a doorstation equipment interface card. The following ports can be used with such a card: two actor ports for connection to a door opener and the intercom of doorstation equipment. These are designed as pressure terminals (actor1 to activate a door opener and actor2 to activate doorstation equipment); three sensor ports for connection to the bell keys of doorstation equipment, designed as pressure terminals (sensor 1 to sensor 3)
■ One slot to incorporate a V.24 interface card. The following port can be used with the V.24 add-on card: one COM port to connect to a PC to configure and transmit connection data, designed as an RJ45 jack
■ One port to the LAN (10BaseT), designed as an RJ45 jack
34
Installation Available Ports
■ One CompactFlash “base” to incorporate a type I or type II CompactFlash memory card. These cards are necessary to operate the OpenVoice and Open-
Attendant program packages. Only use high speed memory cards which are recommended by DeTeWe. Other memory cards or “Microdrive” type memory cards may not be able to maintain the required access speed.
Tip: For the stored voice announcements and a recording time of one hour a memory card with 32 Mbyte is required.
■ One port jack to connect the plug-in power supply to power the basic module.
Only use the original OpenCom 130 plug-in power supply provided in the supply scope to power the basic module.
3.8.2 OpenCom 131
■ One S
0
port to connect to an external S
0
bus (usually the NTBA), designed as an
RJ45 jack (S
0
1)
■ One switchable S
0
port (S
0
2), which can be connected as either an internal or external S
0
bus. The internal connection is via a pressure terminal and the external connection via an RJ45 jack.
■ Three U pn
ports, designed as pressure terminals (U pn
1 to U pn
3)
■ Eight analogue a/b ports, designed as pressure terminals (a/b1 to a/b8)
■ One slot to incorporate a doorstation equipment interface card. The following ports can be used with such a card: two actor ports for connection to a door opener and the intercom of doorstation equipment. These are designed as pressure terminals (actor1 to activate a door opener and actor2 to activate doorstation equipment); three sensor ports for connection to the bell keys of doorstation equipment, designed as pressure terminals (sensor 1 to sensor 3)
■ One slot to incorporate a V.24 interface card. The following port can be used with the V.24 add-on card:
35
Installation Available Ports one COM port to connect to a PC to configure and transmit connection data, designed as an RJ45 jack
■ One port to the LAN (10BaseT), designed as an RJ45 jack
■ One CompactFlash “base” to incorporate a type I or type II CompactFlash memory card. These cards are necessary to operate the OpenVoice and Open-
Attendant program packages. Only use high speed memory cards which are recommended by DeTeWe. Other memory cards or “Microdrive” type memory cards may not be able to maintain the required access speed.
Tip: For the stored voice announcements and a recording time of one hour a memory card with 32 Mbyte is required.
■ One port jack to connect the plug-in power supply. Only use the original
OpenCom 131 plug-in power supply provided in the supply scope.
3.8.3 OpenCom 150
The listed interfaces and ports are located on the main module or on the connection module of the OpenCom 150. Further interfaces and ports can be added
by installing additional interface cards (see Installing Interface Cards starting on page 29).
■ One slot to incorporate a double doorstation equipment interface card. The following ports can be used with such a card:
Four actor ports for connection to a door opener and the intercom of doorstation equipment. These are designed as pressure terminals (actor1 and actor3 to activate door openers, actor2 and actor4 to activate doorstation equipment)
Four sensor ports for connection to the bell keys of doorstation equipment, designed as pressure terminals (sensor 1 to sensor 4)
■ One slot to incorporate a V.24 add-on card. The following port can be used with the V.24 add-on card: one COM port to connect to a PC to configure and transmit connection data, designed as an RJ45 jack
36
