![](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-128x128.png)
advertisement
![ANALOG. Adcon Telemetry MQXA840 | Manualzz ANALOG. Adcon Telemetry MQXA840 | Manualzz](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-360x466.png)
36 CHAPTER 3
Advanced Functions
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
PORT
Acts upon the I/O ports of a remote device.
The RTU’s ID, the byte code, and parameters (for some forms of the command). All parameters are in decimal form (pay particular attention to the byte code because it must be translated to decimal).
Status result, depends on command.
This command is currently supported only by the A720 (series 2) and A723 (series 3) addITs and A733 addWAVE RTUs.
port 9473 0
Dev 9473: incoming RF 255, outgoing RF 255
Value: 255, Error level: 0
OK
ANALOG
Acts upon the analog input ports of a remote device.
The RTU’s ID, the byte code, and parameters (for some forms of the command). All parameters are in decimal form (pay particular attention to the byte code because it must be translated to decimal).
Status result, depends on command.
This command is currently supported only by the A723 (series 3) addITs and the A733 addWAVE RTUs.
analog 9473 0
Dev 9473: incoming RF 255, outgoing RF 255
Average method: 1 2 3 4 5 6 7 5 5 5 5 5 0 0 0 0
Error level: 0
OK
B
Issues a broadcast request frame that forces all listening devices to answer.
None.
A list of devices that answered.
None.
b
From 2003: incoming RF 255, outgoing RF 255
advertisement
Related manuals
advertisement
Table of contents
- 7 Chapter 1. Introduction
- 9 Chapter 2. System Setup
- 9 Package Contents
- 9 Installation
- 12 Installing the Outdoor Unit
- 13 Installing the Indoor Unit
- 14 Initializing the Base Station
- 15 LED Indicators
- 15 Linux Mode
- 15 LAN and ACT
- 15 USR and RUN
- 16 Hermit Mode
- 17 Chapter 3. Advanced Functions
- 17 Administrative Tasks at the System Level
- 18 Stopping and Starting the telemetry gateway
- 19 Changing Passwords
- 20 Losing a Password
- 21 Software Upgrades
- 21 Upgrading the bootloader
- 22 To upgrade the system
- 23 Operations at the Application Level
- 23 Commands Accepted by the emu3ap Emulator
- 24 Configuration Commands
- 24 INSERT
- 24 REPLACE
- 24 DELETE
- 25 ROUTE
- 26 MASTER
- 26 EXTEND
- 26 SET Commands
- 27 SET TIME
- 27 SET FREQ
- 28 SET OWNID
- 28 SET SLOT
- 28 SET DELAY
- 29 SET ECHO/NOECHO
- 29 Data Commands
- 29 GETBLOCK
- 31 Administrative Commands
- 31 INSPECT
- 32 UPTIME
- 32 Direct Radio Commands
- 34 REQUEST
- 35 RSETIO
- 36 ANALOG
- 37 RBLIST
- 38 Error Messages
- 39 Frame Types
- 39 The A730MD frames
- 42 The A720 (addIT) Frames
- 43 The A723 (addIT series 3) Frames
- 45 The A733 (addWAVE) Frames
- 48 Frame Parsing Example