![](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-128x128.png)
advertisement
![RBLIST. Adcon Telemetry MQXA840 | Manualzz RBLIST. Adcon Telemetry MQXA840 | Manualzz](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-360x466.png)
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
CHAPTER 3
Operations at the Application Level
37
From 2646: incoming RF 188, outgoing RF 141
From 9474: incoming RF 255, outgoing RF 255
From 2419: incoming RF 255, outgoing RF 254
From 2464: incoming RF 255, outgoing RF 255
From 10843: incoming RF 255, outgoing RF 255
OK
RB
Forces the specified remote device to issue a broadcast request frame that forces all listening devices to answer. By subsequently using the RBLIST command, a list of all the stations heard from can be retrieved.
The ID of the remote.
OK or error.
Currently only the A723 addIT and the A733 addWAVE devices support this command. At least 12 seconds must elapse between the time you issue the RB and RBLIST commands.
rb 9473
Error level: 0
OK
RBLIST
Returns a list of all the stations heard from after a broadcast request.
The ID of the remote.
A list of the stations heard from.
Currently only the A723 addIT and the A733 addWAVE devices support this command. At least 12 seconds must elapse between the time you issue the RB and RBLIST commands.
rblist 9473
Dev 9473: incoming RF 255, outgoing RF 255
Last Broadcast: Mon Jun 19 12:50:31 2000
201: 255
4446: 255
2622: 255
6127: 255
10820: 255
11127: 255
2646: 255
2008: 255
OK
advertisement
Related manuals
advertisement
Table of contents
- 7 Chapter 1. Introduction
- 9 Chapter 2. System Setup
- 9 Package Contents
- 9 Installation
- 12 Installing the Outdoor Unit
- 13 Installing the Indoor Unit
- 14 Initializing the Base Station
- 15 LED Indicators
- 15 Linux Mode
- 15 LAN and ACT
- 15 USR and RUN
- 16 Hermit Mode
- 17 Chapter 3. Advanced Functions
- 17 Administrative Tasks at the System Level
- 18 Stopping and Starting the telemetry gateway
- 19 Changing Passwords
- 20 Losing a Password
- 21 Software Upgrades
- 21 Upgrading the bootloader
- 22 To upgrade the system
- 23 Operations at the Application Level
- 23 Commands Accepted by the emu3ap Emulator
- 24 Configuration Commands
- 24 INSERT
- 24 REPLACE
- 24 DELETE
- 25 ROUTE
- 26 MASTER
- 26 EXTEND
- 26 SET Commands
- 27 SET TIME
- 27 SET FREQ
- 28 SET OWNID
- 28 SET SLOT
- 28 SET DELAY
- 29 SET ECHO/NOECHO
- 29 Data Commands
- 29 GETBLOCK
- 31 Administrative Commands
- 31 INSPECT
- 32 UPTIME
- 32 Direct Radio Commands
- 34 REQUEST
- 35 RSETIO
- 36 ANALOG
- 37 RBLIST
- 38 Error Messages
- 39 Frame Types
- 39 The A730MD frames
- 42 The A720 (addIT) Frames
- 43 The A723 (addIT series 3) Frames
- 45 The A733 (addWAVE) Frames
- 48 Frame Parsing Example