![](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-128x128.png)
advertisement
![Error Messages. Adcon Telemetry MQXA840 | Manualzz Error Messages. Adcon Telemetry MQXA840 | Manualzz](http://s2.manualzz.com/store/data/062985113_1-c0806289637698a68bec4c5457b60c17-360x466.png)
38 CHAPTER 3
Advanced Functions
D ESCRIPTION
P ARAMETERS
R ETURNS
R EMARKS
E XAMPLE
Error Messages
RSET
Issues remote SET commands, which set parameters in the RTUs.
Not all the RTUs support these commands, most notably the
A730MD devices don’t support it.
The ID of the remote, the set-command, and its parameters.
OK or an error message.
Currently only the A720 (series 2), A723 (series 3) addIT, and the
A733 addWAVE devices support this command. The following remote set commands are supported: ID, SLOT, PMP, FREQ, FDEV, and SST. Not all devices support all commands.
rset 11123 slot 600 10
OK
The emu3ap software might return any of several error messages.
Some are self-recoverable after a retry and others are simply warnings. These messages are returned instead of the OK prompt.
• 1 — Nonexistent command
• 2 — CLI buffer overflow
• 3 — Internal error
• 5 — Invalid or missing parameter
• 10 — Device not found
• 11 — Device already exists
• 13 — No more space for device descriptors
• 14 — No more records for the requested device
• 15 — Remote device currently unavailable (radio connection temporarily interrupted)
• 18 — Reserved device numbers (that is, 0)
• 20 — Incorrect time supplied, conversion not possible
• 30 — Error receiving a frame (cyclic redundancy check and others)
• 31 — An unexpected frame type was received
• 32 — False length (type does not fit its length)
• 35 — Radio timeout when receiving (no answer after a request
• 36 — RF channel in use
advertisement
Related manuals
advertisement
Table of contents
- 7 Chapter 1. Introduction
- 9 Chapter 2. System Setup
- 9 Package Contents
- 9 Installation
- 12 Installing the Outdoor Unit
- 13 Installing the Indoor Unit
- 14 Initializing the Base Station
- 15 LED Indicators
- 15 Linux Mode
- 15 LAN and ACT
- 15 USR and RUN
- 16 Hermit Mode
- 17 Chapter 3. Advanced Functions
- 17 Administrative Tasks at the System Level
- 18 Stopping and Starting the telemetry gateway
- 19 Changing Passwords
- 20 Losing a Password
- 21 Software Upgrades
- 21 Upgrading the bootloader
- 22 To upgrade the system
- 23 Operations at the Application Level
- 23 Commands Accepted by the emu3ap Emulator
- 24 Configuration Commands
- 24 INSERT
- 24 REPLACE
- 24 DELETE
- 25 ROUTE
- 26 MASTER
- 26 EXTEND
- 26 SET Commands
- 27 SET TIME
- 27 SET FREQ
- 28 SET OWNID
- 28 SET SLOT
- 28 SET DELAY
- 29 SET ECHO/NOECHO
- 29 Data Commands
- 29 GETBLOCK
- 31 Administrative Commands
- 31 INSPECT
- 32 UPTIME
- 32 Direct Radio Commands
- 34 REQUEST
- 35 RSETIO
- 36 ANALOG
- 37 RBLIST
- 38 Error Messages
- 39 Frame Types
- 39 The A730MD frames
- 42 The A720 (addIT) Frames
- 43 The A723 (addIT series 3) Frames
- 45 The A733 (addWAVE) Frames
- 48 Frame Parsing Example