Controller Option Select. BusLogic BT-XlO A
विज्ञापन
विज्ञापन
To properly set the attribute, you can boot from a different drive each time.
For example, you have two drives installed with different operating systems and will work with them from time to time. If you work with DOS at the beginning, the setting may look like this:
DRIVE C
DRIVE D
DRIVE E
DRIVE F
Attribute
[DOI
PI
P-4
P31
DOS drive
(no disk)
SC0 UNIX drive
(no disk)
System
C: ==> Boot Drive
D:
If you work with SC0 UNIX next time, the setting may change like the following. If you’re not able to change to the desired options, you can try to set the attribute(s) to [Non-installed] for some of them. This allows more options for the drive you want to work with.
DRIVE C
DRIVE D
DRIVE E
DRIVE F
Attribute
PI
PO1
PI
P31
SC0 UNIX drive
DOS drive
(no disk)
(no disk)
System
C: ==> Boot Drive
D:
I
If more than two drives, link/mirror pair treated as one, are installed, you have to enable the More Than 2 Drives option of the Controller Option
Select module.
Note: Once you have set the drive attributes for mirroring, you must initialize mirroring using the AutoIDE’s Mirror initialization or Repair module described later in this section.
Track-Remap
This
Track-Remapping function is disabled by default and should be enabled only when the capacity of the drive exceeds 528MB.
Note: The INT13 BIOS Selection option in the Controller Option Select module has to be set to Enhanced INT13 (Shadowed or not).
4-6 I BT-XlOA IDE Caching Controller
If installing a previously configured drive,
(1) maintain drive type as 1
Caution: Ifdrive type is not set to 2, all data on drive will be destroyed
(2) and drive cylinder number is >1024, Track Remapping should be disabled or perform a backup of the device before remapping.
installed Drive Information
The bottom portion of the Disk Parameter Setup screen indicates the physical bus connection of drive(s) controlled by the BT-XlOA. The following shows two drives connected to IDE BUS1 and IDE BUS2, respectively.
IDE BUS1 Drive 0 - Maxtor 7213 AT
IDE BUS1 Drive 1 -
IDE BUS2 Drive 0 - ALPS ELECTRIC Co., LTD. DR312C
IDE BUS2 Drive 1 -
C
O N T R O L L E R
O
P T I O N
S
E L E C T
The Controller Option Select screen gives you access to the advanced features supported by the BT-XlOA:
Controller Option Select
I
Cache Line Size
Cache Function
0.5K
Enabled
- Default
More Than 2 Drives Disabled
- Default
INTI 3 BIOS Selection - Enhanced INT13 Shadowed
- Default
- Default
Controller I/O Port
Primary
- Default
Floppy Controller
Enabled
- Default
ROM BIOS Address
C800H
- Default
Green Cache Mode
Disabled
- Default
The AutolDE Utility I 4-7
Cache Line Size
You can set the cache line size to one of the following:
0.5K
(default)
1K
2 K
4 K
8 K
While the default suits most applications, you can select other options for your specific needs. For example, you may want to choose 4K for NetWare system if the block size of its file system is also 4KB.
More Than 2 Drives
The More Than 2 Drives option allows support of up to eight logical drives-an individual drive, linking pair or mirroring pair-under DOS 5.0
and above, Windows and NetWare. Where two BT-XZOAs are installed, enable
this option on the one serving as the seconda y controller togain access to its drives.
Also note that: n n
The INT13 BIOS Selection option on this screen has to be set to
Enhanced INT13 (Shadowed or not).
To support the more than two drive function for other operating systems, you have to install their respective drivers.
INT13 BIOS Selection
INT 13 BIOS allows you to select the INT 13 handler, a DOS software interrupt used to control hard disk I/O (read/write operations). Three options exist: Enhanced INT13 shadowed to system RAM (default), Enhanced INT13 and Mainboard INT13.
EnhancedINT13Shadowed.Thisoptiontakes thatportionofthecontroller’s
ROM which normally handles INT 13, and remaps it to conventional memory (O-640KB), where it occupies 1KB (639KB-640KB). This option is provided, and enabled by default, to ensure compatibility with some early
4-8
I
ET-XIOA IDE Caching Controller versions of BIOS, which may otherwise experience timing problems with the BT-XlOA (and IDE drives generally).
Enhanced INT13: It functions like the previous option except it instructs the controller to handle INT 13 from its ROM address in reserved memory and does not occupy 1KB from the system memory.
Mainboard BIOS INT13: This
option assigns the handling of INT 13 to the system BIOS instead of the controller BIOS. Some versions of BIOS also support the remapping to conventional memory of the INT 13 BIOS handling routines; consult your system manual for details.
Note: Enhanced lNTl3 (Shadowed or not) option must be set to work with
(1) More than 2 drives environment and (2) DOS partition greater than 528MB per drive with Trk-Remap option enabled.
Cache Function
This function allows you to set the cache as Enabled or Disabled. The cache is Enabled by default, but you may find it necessary to temporarily disable the cache (e.g., when installing a new operating system or hardware). When cache status is disabled, data transfer requests and commands are passed directly to the drive itself.
Controller l/O Port
There are two options for the controller I/O port:
Primary
=> port address (lFO-lF7) --> defauZt
Secondary => port address (170-177)
The Seconda y option is useful when another IDE card is installed in the same system. Remember to enable the More Than 2 Drives option to gain access to the drive(s) controlled by the secondary controller. You are allowed to put two BT-XlOA controllers in the system and thus can control up to eight individual drives. (For operating systems other than DOS, device drivers are needed.)
Note: For BT-SlOA, besure thesettingforl’in-5JP3 is sameas theoption set here.
The AutolDE Utility I 4-9
डाउनलोड
विज्ञापन