Mirror Drive Verification. BusLogic BT-XlO A
The BT-XlO A IDE caching controller is a high-performance solution for boosting the performance of IDE hard drives. Designed for “plug-and-play” installation and operation, the BT-XlO A also provides tools to further configure the controller and drives attached to it. The BT-XlO A supports up to four IDE drives. Two controller cards can be installed, for a total per system support of eight drives. The BT-XlO A offers driver support for: MS-DOS or PC-DOS, Windows, OS/2, NetWare, SC0 UNIX. Depending on the product purchased, not all drivers listed are included.
Advertisement
Advertisement
you see a mirroring problem. All of these could cause inconsistency between the two drives. Refer to this screen to check which drive is damaged.
Select the mirror drive for initialization or repair
Status
IDE BUS1 Drive0 - Maxtor 7213AT
0
IDE BUS2 Drive0 - ALPS ELECTRIC Co., LTD. DR312C
D
Source
Target
To restore the mirror pair after the problem has been resolved, you must set the drive marked as D to Target and the one marked as 0 to Source. The beeping alarm will stop right after the mirror repair is completed.
M
I R R O R
D
R I V E
V
E R I F I C A T I O N
This module performs a disk comparison between the two drives of the same mirror pair. You may need tore-do the mirror initialization if incorrect data is found in one of the drives. This module is not available unless the mirroring attribute has been set.
Select the mirror drive for Verification
Status
IDE BUS1 Drive0 - Maxtor 7213AT
0
IDE BUS2 Drive0 - ALPS ELECTRIC Co., LTD. DR312C 0
Source
Target
D
ISK
I
M A G E
C
O P Y
This module copies the data from the source disk to the target disk on a drive-to-drive basis. Select the desired drive using the Up and Down Arrow keys and press <Enter> to execute the copy.
I
D
ISK
I
M A G E
C
O M P A R E
Select source and target disks for image copy
IDE BUS1 Drive0 - Maxtor 7213AT
IDE BUS2 Drive0 - ALPS ELECTRIC Co., LTD. DR312C
Source
Target
This module compares the data of the source disk with that of the target disk on a drive-to-drive basis. Select the desired drive using the Up and Down
Arrow keys and press <Enter> to execute the compare.
Select source and target disks for image compare
IDE BUS2 Drive0 - ALPS ELECTRIC Co., LTD. DR312C
4-14 I ET-XlOA IDE Caching Controller
The AutolDE Utility I 4-15
NETWARE 4.0X
The subdirectory IDENV40X.DSK, contains the NETWARE V4.OX device driver. The following describes the key procedures during driver installation:
After seeing a message block showing “Scanning for available drivers . ..” during the installation, you’ll find a list of default supported drivers.
Press <Ins> key to install the driver, IDENV40.DSK, from drive A:.
Press <F3> key to specify the path: >A:\NETWARE.40. Select
IDENV4O.DSK and press <Enter> to load this driver.
Press <Return> again to set the I/O port address and IRQ.
NETWARE 3.1X
The subdirectory IDENV31X.DSK, contains the NETWARE V3.1X device driver. The installation procedures are the same for NETWARE V3.1 below, except the driver loaded here is IDENV31X.DSK.
NETWARE 3.1
The subdirectory IDENV31.DSK, contains the NETWARE V3.1 device driver. The installation procedures follow:
For one card installation
1. Install the BT-XlOA:
A) Remove other add-on cards that may conflict with BT-XlOA’s
ROM space
B) Select this card as primary
C) Select the ROM space for the BT-XlOA
D) Enable the floppy diskette
2. Plug another add-on card if necessary
3. Boot DOS
5-2 I ET-XlOA IDE Caching Controller
4.
5.
6.
7.
Copy the BusLogic NETWARE driver, IDENW31X.DSK, from the
BusLogic driver diskette to either the NETWARE boot floppy or the
NETWARE subdirectory on your hard drive
Load NETWARE. When the NETWARE server prompt “:” appears
Load IDENV31
Using the NETWARE Install utility, save the NCF files to reflect your new configuration.
6.
7.
8.
3.
4.
5.
Where duplexing is required:
1.
2.
Install the secondary BT-XlOA first:
A) Remove other add-on cards that may conflict with BT-XlOA’s
ROM space
B) Select this card as secondary
C) Select the ROM space for the BT-XlOA
D) Disable the floppy diskette
Install the primary BT-XlOA:
A) Select this card as primary
B) Select the ROM space for the BT-XlOA
C) Enable the floppy diskette
Plug another add-on card if necessary
Boot DOS
Copy the BusLogic NETWARE driver, IDENW31X.DSK, from the
BusLogic driver diskette to either the NETWARE boot floppy or the
NETWARE subdirectory on your hard drive
Load NETWARE. When the NETWARE server prompt ‘I:” appears
Load IDENV31
Using the NETWARE Install utility, save the NCF files to reflect your new configuration.
Driver Installations
I
5-3
NETWARE 2.Xx
This diskette is also labeled as DSK_DRV_003 and two files IDENV215.DSK
and IDENV215.0BJ in the root directory are used as the hard disk device driver for NETWARE V2.15. Follow the NETWARE V2.15’~ installation guide to install the server.
OS/2 v2.x
To install this driver:
1.
2.
3.
Insert the BusLogic driver diskette into the floppy drive
Under OS/2 V2.X, install the driver by keying the following command:
[C:\]
ddinstal
Set the source drive letter to reflect the floppy drive containing the driver diskette
This command copies the file, OS2_32.ADD, from the driver diskette to C:\OS2 directory and replaces the file IBMlS506.ADD in it. The old IBMlS506.ADD will be re-named as IBMlS506.1, which also resides in the C:\OS2 directory.
4. Re-boot the system
To remove the driver:
1. Copy the file, IBMlS506.1, to replace the file, IBMlS506.ADD. Both files are in the same directory, C:\OS2:
[C:\OS2] COPY lBMlS506.1 IBMlS506.ADD
2.
Re-boot the system.
UNIX
For installation in some UNIX environments, cache must be disabled.
Cache must be disabled on the BT-XlOA before you install the SC0 UNIX operating system. For further details, refer to the README file supplied with the product and the UNIX operating system documentation.
5-4 m
BT-XIOA IDE Caching Controller
AT H
ARD
D
RIVE
T
Y P E S
TYP
9
10
11
12
13
14
7
8
5
6
15
1
2
3
4
The first fifteen drive types were defined by IBM in the original AT. Since
then,
additional types have been defined, so the table in your machine may vary.
In the following table, these abbreviations are used:
TYP
CYl
Hds
CmP
Zon
Set
Mb
Drive type number
Number of cylinders
Number of heads
Pre-compensation
Landing zone
Number of sectors
Approximate number of megabytes
CYl
462
733
900
820
855
855
306
733
0
306
615
615
940
940
615
Hds
0
8
7
5
7
15
3
8
5
6
4
6
8
4
4
Zon
511
733
901
820
855
855
305
615
615
940
940
615
319
733
0
Cmp
-1
-1
256
-1
-1
-1
128
-1
0
128
300
300
512
512
-1
Set
17
17
17
17
17
17
17
17
17
17
17
17
0
17
17
AT Hard Drive Types m A-l
M b
20
40
0
30
30
110
20
35
50
10
20
32
64
48
20
Hds
5
7
5
4
5
7
7
4
7
9
7
4
4
7
4
7
5
5
2
8
10
4
4
4
7
6
4
8
3
7
9
8
5
2
7
11
15
7
11
10
A-2 I BT-XlOA IDE Caching Controller
TYP
35
36
37
38
39
40
41
42
28
29
30
31
32
33
34
22
23
24
25
26
27
16
17
18
19
20
2 1
48
49
50
5 1
43
44
45
46
47
52
53
54
55
CYl
977
981
830
830
612
306
1024
612
1024
1024
615
987
987
820
612
698
976
306
611
732
1023
306
1024
733
306
925
925
754
754
699
823
918
1024
1024
612
977
977
1024
733
733
0
0
0
-1
-1
0
0
305
300
488
0
306
300
-1
-1
512
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
300
300
0
0
300
-1
512
300
Set
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
Zon
615
987
987
820
977
981
830
823
918
1024
1024
1024
611
1024
1024
336
925
925
754
754
699
663
977
977
1023
732
733
733
830
663
340
670
732
977
340
663
732
1023
305
1024
Mb
40
24
57
40
42
10
76
68
43
68
40
68
53
93
127
40
10
20
42
42
5
68
IO
20
40
32
32
48
68
20
20
40
56
60
30
42
30
10
53
70
E
RROR
M
ESSAGES AND
G
ENERAL
T
ROUBLESHOOTING
T
IPS
Error codes may be generated at various stages in the Model BT-XlOA’s
BIOS initialization procedure. If an error occurs, the BIOS will display a message accompanied by one of several error codes, which are listed below.
Code Message Description
1 Controller Failure!
2 Controller Failure!
3 Cache Operation Failure!
4 Cache Operation Failure!
5 Cache Operation Failure!
6 Cache Operation Failure!
7 Controller Failure!
Extendedcommandenabled
Query controller information
Write back cache to drive and flush cache
Disable cache
Write cache DRAM
Read cache DRAM
Query controller information error during DRAM test
8 Cache RAM Error at Bank 0
9 Cache RAM Error at Bank 1
DRAM error at bank 0
DRAM error at bank 1
10 Cache RAM Error at Bank 2
DRAM error at bank 2
11 Cache RAM Error at Bank 3
DRAM error at bank 3
12 No Cache RAM Installed!
No DRAM installed
13 Controller Failure!
Read EEPROM
14 Controller Failure!
Write EEPROM
15 Controller EPROM Checksum Error! Controller EPROM checksum error
Error Messages and General Troubleshooting Tips
I
B-l
On powering up the system, if the Model BT-XlOA issues the message Error
Code = 1 with no further details, one of four possibilities exists: w Controller is not functional n
No Cache DRAM is installed n
TAG SRAM test failure n
Parity error on cache DRAM
Power off the system, wait a few moments and then power the system back on. Some versions of BIOS may issue a HDD Controller Failure message if no cache DRAM is installed.
General Troubleshooting Tips
Most controller errors are traceable to external factors, such as conflicts with other installed cards, bad or incorrectly configured drives, loose cables or other installation errors.
When a problem occurs in your system, you can always try to verify the possible causes by changing various components in your system, such as
I/O card, motherboard, DRAM SIMM, or CPU. The following are general guidelines for some specific error conditions.
1. The LED connected to JPl flashes some diagnostics right after power-up. The following shows the flash frequency of each fatal error condition: n n
One short flash: No Cache DRAM installed
Two short flashes: CPU error n
Three short flashes: SRAM error w Four short flashes: Timer error
2. No BIOS message from BT-XlOA, i.e., <Press F2 or F6 . ..>. appears on the screen: n
ROM address conflicting with other I/O card(s). Check the ROM addresses of all the I/O cards and make sure there are no conflicts.
B-2 I ET-XIOA IDE Caching Controller n
VGA card with “Fast Address Decode” option enabled. This may cause all I/O cards that employ &bit ROM BIOS, BT-XlOA included, not to be recognized. Disable this option, if available.
3. Missing operating system: n
Could be the parameters scanned by the BT-XlOA, directly from the drive itself, differ from drive supplier’s. Enter the CUSTOM-
IZED CONFIGURATION module of AutoIDE and key in the parameters provided by drive supplier manually.
4. System hangs after running for a while: n n
ROM BIOS might be “shadowed” by motherboard. Check the setup of your motherboard and disable the “shadow” option on
BT-XlOA’s ROM address.
Cabling (error condition varies). Could try DIAGNOSTIC module of AutoIDE to check if the cabling is O.K.
5. FDC error: n
Could be more than one FDC enabled: make sure only one FDC is enabled.
6. Cannot access HDD: n
Check if the HDD type in your system’s CMOS is set to “1.”
7. Cannot recognize the HDD’s parameters or cannot save them correctly: n
Try to place the jumper cap over JDRO, i.e., short, if the HDD is connected to the FIRST IDE BUS. If connected to SECOND IDE
BUS, then short JDRl.
8. Possible incompatible conditions for default option (CTRL BIOS moved to RAM) of INT 13 BIOS: n
The default option gains the optimal performance. Due to its nature of occupying 1KB (639KB-640KB), some software programs
Error Messages and General Troubleshooting Tips I B-3
may issue false alarms, such as virus-protection software. The above problems can be avoided by choosing another option
“Motherboard BIOS.”
Due to the same nature of 1KB occupancy, the default option may have a conflict when executing the OS/2. Since the OS/2 would only employ its disk I/O routines, the above problem can also be avoided by choosing another option “Motherboard BIOS” without degrading any performance.
Since the CTRL BIOS options are for DOS (Windows) and not related to UNIX, it is recommended that you choose the
“Motherboard BIOS” to operate under these environments.
9. Not able to run with Windows 32-bit driver: n
Change the INT13 BIOS/Customized Configuration option to
“Motherboard BIOS” and install the Windows 32-bit driver during setup.
P
R O D U C T
S
U P P O R T
R
E C O R D
The information on this page should be compiled and provided to your supplier in writing to obtain technical support assistance. This will enable your supplier to respond more rapidly and more appropriately to your problem.
About BusLogic Product:
BusLogic Product No:
Serial Number:
Date of Purchase:
Firmware Version Number:
BIOS Version Number:
Purchased From:
Company:
Address:
Purchased By:
Name/Title:
Company:
Address:
Telephone #:
About System Hardware Configuration:
System Manufacturer:
System Model and Speed:
System BIOS Manufacturer:
Memory in System:
Hard Drives on System:
About System Software Configuration:
Operating System/Version:
Application Program/Version:
Detailed Description of Problem:
B-4 I ET-XIOA IDE Caching Controller
S
TANDARD
W
A R R A N T Y
BusLogic warrants that subject to the terms of this policy the Products shall be free from defects due to faulty material or workmanship on the part of BusLogic for a period of one year from the date of delivery.
This warranty shall not apply if the Products have been subject to misuse by Customer or any other party; if any material alteration, addition, amendment, or modification shall have been carried out without the prior written consent of BusLogic; failure to install or operate the Products in accordance to BusLogic’s Product reference manual; or failure caused by improper or inadequate maintenance of users.
BusLogic will make good by repair or at its option by replacement any
Products which become defective within the warranty period. Repairs will be warranted for 90 days. Products or parts replaced under this provision shall become the property of BusLogic.
BEFORE RETURNING A PRODUCT FOR REPAIR, BUYER MUST RE-
QUEST A RETURN MATERIAL AUTHORlZATlON (RMA) NUMBER FROM
BUSLOGIC.
All Products under warranty returned to BusLogic for repair shall be returned to Customer at BusLogic’s expense. Shipping costs for all Products returned to BusLogic for repair which are out of the warranty period shall be at Customer’s expense both to and from BusLogic.
Customer is expressly prohibited from issuing Debit Memos for material returned under the provisions of this warranty.
BusLogic shall notify Customer in the event that the Products returned for repair are not, in BusLogic’s sole opinion, within this Warranty condition and, unless disposition instructions are given for such Products within thirty (30) days of such notification, the Products will be returned to
Customer freight collect.
EXCEPT FOR THE ABOVE EXPRESS LIMITED WARRANTY, BUSLOGIC
MAKES NO WARRANTlES, EXPRESS, IMPLIED OR STATUTORY, AND
BUSLOGIC SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABlLlTY OR FlTNESS FOR A PARTICULAR PURPOSE.
The total liability of BusLogic for any claim or damage arising out of this
Agreement, and whether in contract or in tort, shall not exceed the price of the individual Product(s) whose defect or damage is the basis of the claim.
IN NO EVENT SHALL BUSLOGIC BE LIABLE FOR ANY LOSS OF PROFlTS
OF FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.
No action against BusLogic for breach of the warranty shall be commenced more than one (1) year after the accrual of the cause of action.
Customer also agrees to perform its duties and responsibilities under
BusLogic’s Warranty Policy, which shall be updated from time to time.
Addendum
The KT-XlOA family of IDE Caching Controllers now supports attachment of up to two (2) ATAPI compatible devices in addition to supporting up to four (4) hard disk drives. Other functionality of the controllers remain the same.
Connector CN4 (refer to Board Diagram) is used to attach ATAPI compliant devices such as CD-ROM and tape drives using a standard 40-pin AT data cable.
If you install two Xl OA Cache Controller in a single system, then you cannot use the ATAPI interface on either board. This is due to the fact that each board requires a primary or secondary port address. Jumper JP3 is used to control this.
With JP3 installed, the secondary port address 170h is used for the ATAPI connector. You must disable jumper JP3 (remove) if you install two XlOA cache controllers in a single system.
JP3 Installed
JP3 Removed
1
ATAPI
Supported
Disable ATAPI
Use second cache controller
Addendum
BusLogic supplies an interrupt bridge paddle board with the BT-9 1 OA to accommodate PC1 systems that can not route the IDE interrupt (INT 14 or
INT 15) to a PC1 slot. In most cases the BT-910A can be installed in your
PC1 system without the interrupt bridge paddle board. Please refer to BT-
X 1 OA User’s Guide chapter 2 for installation instructions. If your system does not boot after installing the BT-9 1 OA, follow these instructions to install the interrupt bridge paddle board and restart your system.
Remove the BT-9 1 OA from your system.
Remove the jumper on JP3-1.
Connect
CNl on the interrupt bridge paddle board to JP4 on the BT-
9
1 OA using the ribbon cable supplied (see diagram below)
Reinstall the BT-9 10A in a PC1 slot.
Insert the interrupt bridge board in the ISA or EISA slot nearest the PC1 slot containing your BT-910A.
/ INTERRUPT BRIDGE PADDLE BOARD
]
Pz Edge Connector J L
PI Edge Connecta
BT-41
OCD Board Diagram
The device driver diskette contains a Windows-based CD-ROM utility for audio and PhotoCD’s. Please refer to the README.CD file found in the <CD_APPS> directory of the driver diskette for installation instructions.
Acer CD625A
N E C MultiSpin_2Vi/CDR-260R
S o n y CDU55E
Mitsumi CRMC-FXOO lDE/FX400
Philips
CR-940
Wearnes CDD- 120
3
BT-91OA
J P 4
Download
Advertisement
Key features
High-speed caching
Up to four IDE drives supported
Onboard memory expandable from 512KB to 16MB
Supports disk mirroring
Supports linking of multiple drives
Power saving mode
AutoIDE configuration utility
Driver support for various operating systems
Easy installation
Frequently asked questions
The BT-XlO A supports up to four independent IDE drives.
The BT-XlO A offers driver support for: MS-DOS or PC-DOS, Windows, OS/2, NetWare, SC0 UNIX.
The BT-XlO A includes an onboard menu-driven AutoIDE configuration utility. You can use AutoIDE to configure drive arrangements, cache operations, and other settings.
Disk mirroring allows you to set up two drives so that both always contain identical information. If one drive fails, the other drive can take over without data loss.