advertisement
![Operating Sequence. Ohaus 7000 Series | Manualzz Operating Sequence. Ohaus 7000 Series | Manualzz](http://s3.manualzz.com/store/data/027218667_1-17284e08f64fd23de6be67c0a0fcbcc7-360x466.png)
7000 SERIES INDICATORS EN 61
Start Threshold
The Start Threshold appears in the menu tree only when Auto Start is Enabled. It defines the scale weight value above which the averaging process will begin after stability is reached.
Valid settings are from 0 to the full scale capacity. This value should be relatively high
– for example, 80% of the estimated weight of all animals on the scale. A very low number may cause the sampling period to start before all the animals are on the scale.
Auto Print
This Auto Print setting overrides the basic weighing Auto Print function, configured in setup at Scale > Log or Print
> Automatic when operating within the application.
When Auto Print is enabled, the processed weight value is displayed for the amount of time defined by the Print
Delay setting, and then a transaction print is automatically triggered.
This feature can be Enabled or Disabled. By default, it is Disabled.
Print Delay
Print Delay is only shown in the menu tree when Auto Print is enabled. It determines the delay between completion of the transaction and triggering the transaction print.
Valid settings are from 0 to 10 seconds in 1 second increments. The default value is 5.
Display
Line 2
The Line 2 assignment determines what data is displayed during and after a transaction. It is selected from a dropdown list. The selection list varies depending on the Mode selected:
Selection
Function
Mode 1
Disabled Line 2 is blank.
Mode 2
Average
ID
Not available
Line 2 shows the transaction ID
Line 2 shows Average weight per animal
Line 2 shows the transaction ID
The default value is Disabled.
4.2.4 Operating Sequence
The following sections describe the two modes of operation of the animal weighing application:
Mode 1 Determines the average total weight of a single animal or multiple
Mode 2 animals
Determines the average total weight of multiple animals, and calculates the average weight per animal
Mode 1 Operation
Begin with the scale empty and the terminal in the Animal Weighing application.
The display will prompt either Press ENTER to start. In normal operation or if Auto Start is enabled, the system will prompt Add weight > xxx (i.e., greater than xxx), where xxx is the programmed threshold weight.
Press ZERO to capture an accurate zero reference.
If required, a transactional ID may be entered via the ID key
Line 2 at the bottom of the display.
. If programmed in setup, the ID will be shown on
Add the desired number of animals to the scale and then press the ENTER key
to start the weighing cycle. If
Auto Start is enabled, the cycle will start automatically when the weight on the scale exceeds the programmed threshold and there is no-motion on the scale.
advertisement
Related manuals
advertisement
Table of contents
- 7 INTRODUCTION
- 11 COM2 Serial Port
- 11 Discrete I/O
- 11 Ethernet
- 12 SD Memory Option
- 18 NSTALLATION
- 18 Display Layout
- 18 Front Panel Keys
- 19 OPERATION: TERMINAL
- 19 Display Elements
- 20 Keypad Operation
- 22 Language Selection – F Codes
- 22 Menu Navigation
- 24 Alibi Memory
- 25 Adjust Contrast
- 25 Transaction Counter
- 25 Totals Memory
- 26 Expand x
- 26 Information Recall
- 27 Setup Access
- 30 Unit Switching
- 31 Expand By
- 31 Print
- 31 Information Recall
- 31 ID Entry
- 32 Time and Date
- 32 Totalization
- 32 Alibi Memory
- 33 Animal Weighing
- 33 Checkweighing
- 33 Counting
- 34 CONFIGURATION: TERMINAL
- 34 Navigation
- 35 Setup Page
- 37 Scale
- 45 Application
- 49 Terminal
- 54 Communication
- 60 Maintenance
- 65 APPLICATIONS: CONFIGURATION AND OPERATION
- 65 Overview
- 65 Operational Features
- 66 Configuration
- 67 Operating Sequence
- 68 Serial Input Commands
- 69 Print Formats
- 70 Overview
- 70 Operational Features
- 71 Configuration
- 74 Operating Sequence
- 78 Print Formats
- 79 Overview
- 79 Operational Features
- 80 Configuration
- 82 Operating Sequences
- 85 Print Formats
- 87 SERVICE AND MAINTENANCE
- 87 Blank Display
- 88 Power Test
- 88 Problem Diagnosis
- 88 Error Codes and Error Messages
- 89 Internal Diagnostics
- 92 Backup to SD Memory Card
- 93 Restore from SD Memory Card
- 95 COMPLIANCE
- 97 APPENDIX A DEFAULT TEMPLATES
- 99 APPENDIX B ALIBI MEMORY
- 102 APPENDIX C COMMUNICATIONS
- 128 APPENDIX D GEO CODES