ALEOS User Guide
Services
AMS (AirLink Management Services)
Table F-16: Services > AirLink Management Services Commands
Command Description
*AMS_ENABLE
Connect or disconnect the device remotely to AirLink Management Services.
•
n=0 : Disabled
•
n=1 : Enabled
Enter the server URL (e.g., http://na.m2mop.net/device/msci)
Indicate (in minutes) how often the device communicates to AirLink Management Services.
*AMS_SERVER
*AMS_INTERVAL
*AMS_ACCOUNT
*AMS_IDENTITY
*AMS_STATUS
*AMSCHECKIN
Enter the registered company name in AirLink Management Services.
Report the identity of the device name on AirLink Management Services.
Display the last known status of the AirLink Management Services connection.
Prompts the device to send a heartbeat message to AirLink Management Services. Once
AirLink Management Services receives the heartbeat message, it can respond and send an
AT Command to the device.
262 4112515
Low Power
Table F-17: Services > Low Power Commands
Command Description
VLTG
PTMR
SISE
Set or query the voltage level at which the device goes into low power mode.
•
n=0 : Ignore voltage for power control.
•
n=threshhold in tenths of volts
Example: ATVLTG=130 would place the device in a low power use, standby state if the voltage goes below 13.0V.
Number of minutes after the VTLG power down event happens until the device enters the low power mode. If VLTG is 0 (zero), this setting does nothing.
•
n=0–255 minutes
Note: There is always a minimum of 1 minute between power down event and actual shutdown (to give the device time to prepare); entering zero will not power down the device immediately.
Standby Ignition Sense Enable: the AirLink device will monitor the ignition sense on the power connector and enter the low power consumption stand-by mode when the ignition is turned-on (Enabled).
•
n=0 : Disabled (default)
•
n=1 : Enabled
Rev. 6 May.13
263
ALEOS User Guide
Dynamic DNS
Table F-18: Services > Dynamic DNS Commands
Command Description
*dyndns
*MODEMNAME
Configures the Dynamic DNS service.
•
n=0 : Disable (default)
•
n=2 : dyndns.org
•
n=5 : noip.org
•
n=6 : ods.org
•
n=8 : regfish.com
•
n=9 : tzo.org
•
n=10 : IP manager
Name of the device (up to 20 characters long) to use when performing IP address change notifications to IP Manager. The value in *DOMAIN provides the domain zone to add to this name.
•
name=device name (for example, mydevice)
Example: If *deviceNAME=mydevice and *DOMAIN=eairlink.com, then the device's fully qualified domain name is mydevice.eairlink.com.
Automatically Generated Names:
•
#I3 — The ESN/IMEI will be used as the name.
•
#CCID — The CCID will be used as the name.
•
#NETPHONE — The phone number will be used as the name.
Tip:
Each device using IP Manager needs a unique name. I.e., two devices cannot both be called “mydevice”. One could be named “mydevice1” while the other could be named
“mydevice”.
*DOMAIN
*IPMANAGER1
*IPMANAGER2
Domain (or domain zone) of which the device is a part. This value is used during name resolutions if a fully qualified name is not provided and also for DNS updates. This value can be up to 20 characters long.
•
name=domain name (i.e. eairlink.com)
If *DOMAIN=eairlink.com, then when ATDT@remote1 is entered, the fully qualified name remote1.eairlink.com will be used to perform a DNS query to resolve the name to an IP address.
Tip:
Only letters, numbers, hyphens, and periods can be used in a domain name.
Sets a domain name or IP address to send IP change notifications to. Up to two independent IP Manager servers can be set, using either AT*IPMANAGER1 or
AT*IPMANAGER2. Updates to a server can be disabled by setting that entry to nothing (e. g., “AT*IPMANAGER1=”).
•
n=1 : First IP Manager server.
•
n=2 : Second IP Manager server.
264 4112515
Table F-18: Services > Dynamic DNS Commands (Continued)
Command Description
*IPMGRUPDATE1
*IPMGRUPDATE2
*IPMGRKEY1
*IPMGRKEY2
Sets the number of minutes to periodically send an IP update notification to the corresponding server. This will occur even if the IP address of the device does not change.
*IPMGRUPDATE1 is used to set the refresh rate to *IPMANAGER1, while
*IPMGRUPDATE2 is used with *IPMANAGER2. If the value is set to 0, then periodic updates will not be issued (i.e., IP change notifications will only be sent when the IP actually changes).
•
n=1 : First IP Manager server.
•
n=2 : Second IP Manager server.
•
m=0, 5–255 : Number of minutes to send an update.
Sets the 128-bit key to use to authenticate the IP update notifications. If the key's value is all zeros, a default key will be used. If all the bytes in the key are set to FF, then no key will be used (i.e., the IP change notifications will not be authenticated). AT*IPMGRKEY1 is used to set the key to use with AT*IPMANAGER1, while AT*IPMGRKEY2 is used to the key with
AT*IPMANAGER2.
•
n=1 : First IP Manager server.
•
n=2 : Second IP Manager server.
•
key=128-bit key in hexadecimal [32 hex characters]
Rev. 6 May.13
265
ALEOS User Guide
SMS
Table F-19: Services > SMS Commands
Command Description
*securemode
This AT command enables/disables Services.
"AT*securemode=value"
0 — Will be the default, and leave the modem in its normal open state.
1 — Will disable the Aleos Ports for OTA and Wi-Fi access
2 — Will disable the Aleos Ports for OTA and Local Access+ Wi-Fi (All)
3+ — All values larger than 2 will receive an error response.
*SMSM2M
*SMSM2M_8
*SMSM2M_u
*SMSM2M_T
The DHCP and the Telnet ports will not be blocked.
Responses to outgoing Aleos message that are sent OTA will be allowed into Aleos, so
GPS and DNS will work.
*SMSM2M is the command for ASCII text.
*SMSM2M_8 is the command for 8-bit data.
*SMSM2M_u is the command for unicode.
Format:
*smsm2m=”[phone][ascii message]”
*smsm2m_8=”[phone][hex message]”
*smsm2m_u=”[phone][hex message]”
*smsm2m_T=”[phone][address type] message”
[address type] is 2 digits. The first is the address type, the second is the address plan. See
SMS Address Type and Address Numbering Plan on page 107 for details.
Note: The phone number can only consist of numbers (NO spaces or other characters).
The phone number should be as it appears in the Last Incoming Phone Number field.
• Example 1 (US): 14085551212 (including leading 1 and area code)
• Example 2 (US): 4085551212 (ignore leading 1, include area code)
• Example 3 (UK): 447786111717 (remove leading 0 and add country code)
Command Examples:
*smsm2m=”18005551212 THIS IS A TEST” sends in ASCII.
*smsm2m_8="17604053757 5448495320495320412054455354" sends the message “THIS IS A TEST” as 8-bit data.
*smsm2m_u="17604053757
000102030405060708090a0b0c0d0e0f808182838485868788898A8b8c8d8e8f" sends the bytes:
00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f
80 81 82 83 84 85 86 87 88 89 8a 8b 8c 8d 8e 8f
Note: Not all cellular carriers support 8-bit or unicode SMS messages.
*SMS_PASSWORD
*CGSMS=n
This AT command adds password security to SMS. The password can be both set and queried.
This AT command allows you to change the radio module configuration to enable SMS.
“AT*CGSMS=n” n values are 0, 1, 2, or 3.
266 4112515
Telnet/SSH
Table F-20: Services > Telnet/SSH Commands
Command Description
*TSSH
*TPORT
*TELNETTIMEOUT
E
*SNMPPORT
*SNMPSECLVL
*SNMPTRAPDEST
*SNMPCOMMUNITY
.AT command access mode. Telnet is the default.
Sets or queries the port used for the AT Telnet server. If 0 is specified, the AT Telnet server will be disabled. The default value is 2332.
•
n=0 : Disabled.
•
n=1–65535
Many networks have the ports below 1024 blocked. It is recommended to use a higher numbered port.
Telnet port inactivity time out. By default, this value is set to close the AT telnet connection if no data is received for 2 minutes.
•
n=minutes
Toggle AT command echo mode.
•
n=0 : Echo Off.
•
n=1 : Echo On.
With more than one connection types (serial, and Telnet, and USB) the echo command can be set differently on each interface.
This controls which port the SNMP Agent listens on.
•
n=0 : SNMP is disabled
•
n=1–65535
Selects the security level requirements for SNMP communications.
•
n=0 : No security required. SNMPv2c and SNMPv3 communications are allowed.
•
n=1 : Authentication equivalent to “authNoPriv” setting in SNMPv3. SNMPv3 is required to do authentication, SNMPv2c transmissions will be silently discarded.
•
n=2 : Authentication and encryption equivalent to “authPriv”' setting in SNMPv3.
SNMPv3 is required to do authentication and encryption, SNMPv2c and SNMPv3 authNoPriv transmissions will be silently discarded. Messages are both authenticated and encrypted to prevent a hacker from viewing its contents.
Controls destination for SNMP Trap messages. If the port is 0 or the host is empty, traps are disabled. Traps are sent out according to the SNMP security level (i.e., if the security level is
2, traps will be authenticated and encrypted). Currently, the only trap that can be generated is linkup.
•
host=IP address
•
port=TCP port
The SNMP Community String acts like a password to limit access to the device’s SNMP data.
•
string =string of no more than 20 characters (default = public).
Rev. 6 May.13
267
ALEOS User Guide
Email (SMTP)
Table F-21: Services > Email (SMTP) Commands
Command Description
*SMTPRADDR
*SMTPFROM
*SMTPUSER
Specify the IP address or Fully Qualified Domain Name (FQDN) of the SMTP server to use.
•
d.d.d.d=IP Address
•
name=domain name (maximum: 40 characters).
Sets the email address from which the SMTP message is being sent.
•
email=email address (maximum: 30 characters).
The email account username to authenticate with the SMTP server (*SMTPADDR) for sending email.
•
user=username (maximum: 40 characters).
*SMTPPW
Note: Not required to use SMTP settings but may be required by your cellular carrier.
Sets the password to use when authenticating the email account (*SMTPFROM) with the server (*SMTPADDR).
•
pw= password
Note: Not required to use SMTP settings but may be required by your cellular carrier.
*SMTPSUBJ
Allows configuration of the default Subject to use if one isn't specified in the message by providing a “Subject: xxx” line as the initial message line.
•
subject=message subject
268 4112515
