![](http://s1.manualzz.com/store/data/048868902_1-a5ce8e8268f849ab2955495800eac8c3-128x128.png)
advertisement
![DMS Go Operator' | Manualzz DMS Go Operator' | Manualzz](http://s1.manualzz.com/store/data/048868902_1-a5ce8e8268f849ab2955495800eac8c3-360x466.png)
Chapter 2. Instrument Setup
2.6 Using the Calibration Reminder Alarm (PROBE & CAL - CAL REMINDER)
The DMS Go incorporates a timed alarm feature that causes an icon to appear on user-defined input intervals. To use this alarm:
1.
In the
MAIN menu, scroll to the PROBE & CAL submenu using the joystick (
).
2.
Use the joystick ( ) to select the function titled CAL
REMINDER. The CALIBRATION REMINDER CONFIG window opens. Input the mode, or the parameter that will trigger the reminder (
TIME IN MINUTES, NUMBER OF READINGS, POWER ON, and OFF) and then the value the reminder alarm will trigger. Setting this value automatically resets the alarm to trigger on the specified intervals. This function also allows the alarm to be disabled (
OFF).
3.
Press the function toggle or move the joystick ( ) to change the alarm interval.
4.
Press F2 (
CONFIRM) to acknowledge the triggered alarm and reset it to resume normal operation or F 4 (EXIT) to close the window without changing the alarm setting.
Note: The selection of the VELOCITY function also resets the alarm.
70 DMS Go Operator’s Manual
Chapter 3. Creating Data Recorder Files
Chapter 3. Creating Data Recorder Files
The on-board data recorder option of the DMS Go is a flexible, powerful tool for managing ultrasonic thickness data. It can store, evaluate, display, and report on various types of measurement data. The Data Recorder (
DR) menu functions are shown in Figure 22 below.
DMS Go Operator’s Manual
Figure 22: The DR Menu
65
advertisement
Related manuals
advertisement
Table of contents
- 22 1.1 Supplying Power to the Instrument
- 24 1.2 Powering the Instrument ON and OFF
- 24 1.3 Using the Keypad
- 26 1.3.1 Instrument Orientation
- 27 1.3.2 Keypad Components
- 29 1.3.1 Joystick Functions
- 30 1.3.2 Multi-Key Functions
- 32 1.4 Using the Display
- 33 1.4.1 Portrait Mode
- 35 1.5 Display Icons
- 36 1.6 Using the SD Slot, USB Connector & I/O Connector
- 37 1.6.1 Removing the SD Card
- 37 1.6.2 Inserting the SD Card
- 38 1.6.3 Connecting the USB Port
- 39 1.6.4 Connecting the I/O Port
- 40 1.7 Typical DMS Go Operation
- 41 1.8 DMS Go Software Options
- 43 2.1 Display Screen and Keypad Features
- 46 2.2 The Menu System
- 48 2.3 Initial Setup
- 49 2.3.1 Language, Units of Measurement, Date, and Time
- 56 2.3.2 Screen Appearance
- 70 2.3.3 Setting Security Functions
- 78 2.4 Installing a Probe
- 78 2.4.1 Connecting the Probe
- 80 2.4.2 Configuring the Instrument
- 85 2.5 Calibration
- 86 2.5.1 1-Point Calibration (PROBE & CAL - CALIBRATION)
- 90 2.5.2 2-Point Calibration (PROBE & CAL - CALIBRATION)
- 91 2.5.3 Calibrating by Material Velocity (PROBE&CAL - VELOCITY)
- 92 2.5.4 Adjusting Temperature Compensation (PROBE & CAL - TEMP COMP)
- 94 2.6 Using the Calibration Reminder Alarm (PROBE & CAL - CAL REMINDER)
- 96 3.1 Creating a Data File (DR - EXPLORER - NEW)
- 108 3.2 Creating Master Comments for Addition to a File (DR - MASTER CMT)
- 110 3.3 Setting Up the Meter to Overwrite Data (DR-OVERWRITE)
- 111 3.4 Accessing the Data Recorder File
- 111 3.4.1 Selecting a Data File (DR - EXPLORER)
- 112 3.5 Making and Recording Measurements
- 113 4.1 Setting up Data Measurements
- 113 4.1.1 Positioning Gate A and Gate B
- 117 4.1.2 Selecting the Measurement Method (MEASURE - MODE)
- 119 4.1.1 Setting up a Dual Element Transducer (MEASURE - DUAL MULTI)
- 120 4.2 Adjusting the Display
- 120 4.2.1 Setting the Display Range (MEASURE - DISPLAY RANGE)
- 123 4.2.2 Setting the Display Delay (MEASURE-DISPLAY DELAY)
- 124 4.2.3 Setting the Freeze (MEASURE - FREEZE)
- 125 4.2.4 Setting the MAX GAIN MODE (MEASURE - MAX GAIN MODE)
- 127 4.2.5 Setting Gate Alarms
- 130 4.3 Displaying Measured Results (MEASURE- RESULTS)
- 134 5.1 Loading a Stored PARAM File (PARAM-LOAD P-SET)
- 135 5.2 Saving a New Parameter File (PARAM-SAVE P-SET)
- 137 6.1 Selecting a Data File (DR - EXPLORER)
- 140 6.2 Viewing the Data Recorder File in a List or Spread Format (DR - VIEW)
- 142 6.3 Using Existing Data Recorder Files (DR - PROPERTIES)
- 144 6.3.1 Moving to a Specific Data Point (DR-PROPERTIES-RECORD)
- 145 6.3.2 Modifying Data Entry (DR-PROPERTIES-RECORD)
- 147 6.3.3 Viewing File Statistics (DR-PROPERTIES-STATS)
- 149 6.3.4 Editing the File Header (DR-PROPERTIES-HEADER)
- 150 6.3.5 Changing the Size of the Data Recorder File (DR - PROPERTIES - EDIT)
- 152 6.3.6 Adding or Modifying Comments (DR-PROPERTIES-COMMENT)
- 153 6.4 Adding a Comment to a Stored Value
- 154 6.5 Adding a Micro-Grid to a Stored Value
- 154 6.5.1 Creating and Navigating Within a Micro-Grid
- 155 6.6 Exporting the Active File (DR - EXPORT)
- 157 A.1 Display
- 157 A.1.1 Active Area
- 157 A.1.2 Size
- 157 A.1.3 Pixel Resolution
- 158 A.2 Environment
- 158 A.2.1 Languages
- 158 A.2.2 Size
- 158 A.2.3 Weight
- 158 A.2.4 Temperature Shock (Storage)
- 158 A.2.5 Vibration
- 159 A.2.6 Shock
- 159 A.2.7 Loose Cargo (In Shipping Container)
- 159 A.2.8 Transit Drop (Packaged for Shipment)
- 159 A.2.9 Operating Temperature Range
- 159 A.2.10 Storage Temperature Range
- 159 A.2.11 Dust Proof / Water Proof
- 160 A.2.12 Hazardous Atmosphere Operation
- 160 A.3 Compliance
- 160 A.3.1 EMC/EMI
- 160 A.3.2 Ultrasound
- 160 A.4 I/O Connectors
- 161 A.5 Power Supply
- 161 A.5.1 Battery Type
- 161 A.5.2 Operating Time
- 161 A.5.3 Charger
- 161 A.6 Measuring Range
- 162 A.7 Digital Display Resolution
- 162 A.8 Material Velocity Range
- 162 A.9 Units
- 162 A.10Measurement Techniques
- 162 A.10.1 DMS Go TC Only
- 163 A.11Measurement Display Modes
- 163 A.12Calibration
- 163 A.13Update Rate
- 163 A.14Receiver
- 164 A.15Pulser
- 164 A.16Memory
- 164 A.17Data Recorder
- 164 A.18File Formats
- 164 A.19Attachments
- 165 A.20Application Software
- 165 A.20.1 UltraMATE LITE
- 165 A.20.2 UltraMATE
- 165 A.20.3 Software Development Kit
- 168 B.1 Linear File
- 169 B.2 Custom Linear
- 170 B.2.1 Custom Linear File Example
- 171 B.3 Grid File
- 172 B.4 Custom Grid File
- 173 B.4.1 Grid File Flexibility
- 174 B.5 Boiler File
- 176 B.5.1 Boiler File Flexibility
- 177 B.5.2 Example of Boiler File
- 178 B.6 Custom Point File
- 180 B.6.1 Example of Custom Point File