advertisement
Chapter 6. Working with Recorded Data
6.3.2
Modifying Data Entry (DR-PROPERTIES-RECORD)
In the
RECORD submenu, you can also modify the way in which the DMS Go enters data into the file.When operating in the MEASURE menu, a user stores thickness measurement in the active data file location by pressing F 2
(SEND) . Then, the instrument typically advances automatically, making the next point in the data file active. However, you can modify the AUTO-ADVANCE feature to suit specific measurement applications. For instance, when recording measurements into a large grid type file, the physical measurement site may dictate that it’s best to advance by column. Thus, the active data point would automatically move horizontally across the file window, and all the way through the last column before moving down to the next point or row in the file.
Once the AUTO-ADVANCE feature has moved through a column of data, it will then move on the next column or point, and move through all of the rows in that column of data. If AUTO REVERSE is turned ON, when data is recorded in the last row, the next position will be at the last position of the next column. If AUTO REVERSE is OFF (the default position), the next position will be at the first position of the next column.
To change how the DMS Go enters data:
1.
From the
RECORD submenu, use the joystick to scroll to SEND FUNCTION. You can choose from three selections: Thickness,
Thickness + ASCAN, and Thickness/Thickness + ASCAN.
2.
Scroll to
ADVANCE TIME. You can select a time at which the file will automatically advance from 0.0 to 3.0 sec (in 0.5 sec increments).
3.
Scroll to
1st ADVANCE BY. Depending on your file type, the selections can include Row, Column, Location, Point, and Elevation.Set the first advance value to the file component you wish to auto-advance through first.
4.
Scroll to
1st ADVANCE DIR.The options are the FORWARD and BACKWARD directions, which determine whether the auto-advance moves in the direction of increasing (+) or decreasing (-). Set the desired direction.
DMS Go Operator’s Manual 115
Chapter 6. Working with Recorded Data
6.3.2
Modifying Data Entry (DR-PROPERTIES-RECORD) (cont.)
5.
Scroll to
AUTO REVERSE (shown in Figure 32 below). Select ON or OFF.
116
Figure 32: Data Entry in the Grid
DMS Go Operator’s Manual
advertisement
Related manuals
advertisement
Table of contents
- 22 1.1 Supplying Power to the Instrument
- 24 1.2 Powering the Instrument ON and OFF
- 24 1.3 Using the Keypad
- 26 1.3.1 Instrument Orientation
- 27 1.3.2 Keypad Components
- 29 1.3.1 Joystick Functions
- 30 1.3.2 Multi-Key Functions
- 32 1.4 Using the Display
- 33 1.4.1 Portrait Mode
- 35 1.5 Display Icons
- 36 1.6 Using the SD Slot, USB Connector & I/O Connector
- 37 1.6.1 Removing the SD Card
- 37 1.6.2 Inserting the SD Card
- 38 1.6.3 Connecting the USB Port
- 39 1.6.4 Connecting the I/O Port
- 40 1.7 Typical DMS Go Operation
- 41 1.8 DMS Go Software Options
- 43 2.1 Display Screen and Keypad Features
- 46 2.2 The Menu System
- 48 2.3 Initial Setup
- 49 2.3.1 Language, Units of Measurement, Date, and Time
- 56 2.3.2 Screen Appearance
- 70 2.3.3 Setting Security Functions
- 78 2.4 Installing a Probe
- 78 2.4.1 Connecting the Probe
- 80 2.4.2 Configuring the Instrument
- 85 2.5 Calibration
- 86 2.5.1 1-Point Calibration (PROBE & CAL - CALIBRATION)
- 90 2.5.2 2-Point Calibration (PROBE & CAL - CALIBRATION)
- 91 2.5.3 Calibrating by Material Velocity (PROBE&CAL - VELOCITY)
- 92 2.5.4 Adjusting Temperature Compensation (PROBE & CAL - TEMP COMP)
- 94 2.6 Using the Calibration Reminder Alarm (PROBE & CAL - CAL REMINDER)
- 96 3.1 Creating a Data File (DR - EXPLORER - NEW)
- 108 3.2 Creating Master Comments for Addition to a File (DR - MASTER CMT)
- 110 3.3 Setting Up the Meter to Overwrite Data (DR-OVERWRITE)
- 111 3.4 Accessing the Data Recorder File
- 111 3.4.1 Selecting a Data File (DR - EXPLORER)
- 112 3.5 Making and Recording Measurements
- 113 4.1 Setting up Data Measurements
- 113 4.1.1 Positioning Gate A and Gate B
- 117 4.1.2 Selecting the Measurement Method (MEASURE - MODE)
- 119 4.1.1 Setting up a Dual Element Transducer (MEASURE - DUAL MULTI)
- 120 4.2 Adjusting the Display
- 120 4.2.1 Setting the Display Range (MEASURE - DISPLAY RANGE)
- 123 4.2.2 Setting the Display Delay (MEASURE-DISPLAY DELAY)
- 124 4.2.3 Setting the Freeze (MEASURE - FREEZE)
- 125 4.2.4 Setting the MAX GAIN MODE (MEASURE - MAX GAIN MODE)
- 127 4.2.5 Setting Gate Alarms
- 130 4.3 Displaying Measured Results (MEASURE- RESULTS)
- 134 5.1 Loading a Stored PARAM File (PARAM-LOAD P-SET)
- 135 5.2 Saving a New Parameter File (PARAM-SAVE P-SET)
- 137 6.1 Selecting a Data File (DR - EXPLORER)
- 140 6.2 Viewing the Data Recorder File in a List or Spread Format (DR - VIEW)
- 142 6.3 Using Existing Data Recorder Files (DR - PROPERTIES)
- 144 6.3.1 Moving to a Specific Data Point (DR-PROPERTIES-RECORD)
- 145 6.3.2 Modifying Data Entry (DR-PROPERTIES-RECORD)
- 147 6.3.3 Viewing File Statistics (DR-PROPERTIES-STATS)
- 149 6.3.4 Editing the File Header (DR-PROPERTIES-HEADER)
- 150 6.3.5 Changing the Size of the Data Recorder File (DR - PROPERTIES - EDIT)
- 152 6.3.6 Adding or Modifying Comments (DR-PROPERTIES-COMMENT)
- 153 6.4 Adding a Comment to a Stored Value
- 154 6.5 Adding a Micro-Grid to a Stored Value
- 154 6.5.1 Creating and Navigating Within a Micro-Grid
- 155 6.6 Exporting the Active File (DR - EXPORT)
- 157 A.1 Display
- 157 A.1.1 Active Area
- 157 A.1.2 Size
- 157 A.1.3 Pixel Resolution
- 158 A.2 Environment
- 158 A.2.1 Languages
- 158 A.2.2 Size
- 158 A.2.3 Weight
- 158 A.2.4 Temperature Shock (Storage)
- 158 A.2.5 Vibration
- 159 A.2.6 Shock
- 159 A.2.7 Loose Cargo (In Shipping Container)
- 159 A.2.8 Transit Drop (Packaged for Shipment)
- 159 A.2.9 Operating Temperature Range
- 159 A.2.10 Storage Temperature Range
- 159 A.2.11 Dust Proof / Water Proof
- 160 A.2.12 Hazardous Atmosphere Operation
- 160 A.3 Compliance
- 160 A.3.1 EMC/EMI
- 160 A.3.2 Ultrasound
- 160 A.4 I/O Connectors
- 161 A.5 Power Supply
- 161 A.5.1 Battery Type
- 161 A.5.2 Operating Time
- 161 A.5.3 Charger
- 161 A.6 Measuring Range
- 162 A.7 Digital Display Resolution
- 162 A.8 Material Velocity Range
- 162 A.9 Units
- 162 A.10Measurement Techniques
- 162 A.10.1 DMS Go TC Only
- 163 A.11Measurement Display Modes
- 163 A.12Calibration
- 163 A.13Update Rate
- 163 A.14Receiver
- 164 A.15Pulser
- 164 A.16Memory
- 164 A.17Data Recorder
- 164 A.18File Formats
- 164 A.19Attachments
- 165 A.20Application Software
- 165 A.20.1 UltraMATE LITE
- 165 A.20.2 UltraMATE
- 165 A.20.3 Software Development Kit
- 168 B.1 Linear File
- 169 B.2 Custom Linear
- 170 B.2.1 Custom Linear File Example
- 171 B.3 Grid File
- 172 B.4 Custom Grid File
- 173 B.4.1 Grid File Flexibility
- 174 B.5 Boiler File
- 176 B.5.1 Boiler File Flexibility
- 177 B.5.2 Example of Boiler File
- 178 B.6 Custom Point File
- 180 B.6.1 Example of Custom Point File