Using the AUX port. Toyota Tacoma, 2015, Tacoma 2015, 2015 Tacoma
Advertisement
Advertisement
3-2. Using the multimedia system
■ About iPod
● “Made for iPod”, “Made for iPhone” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards.
● Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone or iPad may affect wireless performance.
● iPad, iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. Lightning is a trademark of Apple Inc.
■ iPod cover art
● Depending on the iPod and songs in the iPod, iPod cover art may be displayed.
● This function can be changed to on/off. (
● It may take time to display iPod cover art, and the iPod may not be operated while the cover art display is in process.
● Only iPod cover art that is saved in JPEG format can be displayed.
3
271
3-2. Using the multimedia system
■ iPod functions
● When an iPod is connected and the audio source is changed to iPod mode, the iPod will resume play from the same point in which it was last used.
● Depending on the iPod that is connected to the system, certain functions may not be available. If a function is unavailable due to a malfunction (as opposed to a system specification), disconnecting the device and reconnecting it may resolve the problem.
● While connected to the system, the iPod cannot be operated with its own controls. It is necessary to use the controls of the vehicle’s multimedia system instead.
● When the battery level of an iPod is very low, the iPod may not operate. If so, charge the iPod before use.
● Compatible models (
P. 274)
■ iPod problems
To resolve most problems encountered when using your iPod, disconnect your iPod from the vehicle iPod connection and reset it. For instructions on how to reset your iPod, refer to your iPod Owner’s Manual.
272
3-2. Using the multimedia system
■ Error messages
Message
“Connection error.
Please consult your
Owner’s Manual for instructions on how to connect the iPod.”
“No music files found.”
“There are no songs available for playback.
Please add compatible files to your iPod.”
“Please check the iPod firmware version.”
“iPod authorization unsuccessful.”
Cause/Correction procedures
This indicates a problem in the iPod or its connection.
This indicates that there is no music data in the iPod.
This indicates that songs are not found in a selected playlist.
3
This indicates that the software version is not compatible.
Please check the compatible models.
(
P. 274)
This indicates that the display multimedia system failed to authorize the iPod.
Please check your iPod.
273
3-2. Using the multimedia system
■ Compatible models
The following iPod
®
, iPod nano
®
, iPod classic
®
, iPod touch
®
and iPhone
® devices can be used with this system.
● Made for
• iPod touch (5th generation)
• iPod touch (4th generation)
• iPod touch (3rd generation)
• iPod touch (2nd generation)
• iPod touch (1st generation)
• iPod classic
• iPod with video
• iPod nano (7th generation)
• iPod nano (6th generation)
• iPod nano (5th generation)
• iPod nano (4th generation)
• iPod nano (3rd generation)
• iPod nano (2nd generation)
• iPod nano (1st generation)
• iPhone 5
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
Depending on differences between models or software versions etc., some models might be incompatible with this system.
CAUTION
■ While driving
Do not connect an iPod or operate the controls.
274
3-2. Using the multimedia system
NOTICE
■ To prevent damage to the iPod or its terminals
● Do not leave the iPod in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the iPod.
● Do not push down on or apply unnecessary pressure to the iPod while it is connected.
● Do not insert foreign objects into the port.
3
275
3-2. Using the multimedia system
Listening to a USB memory device
Connecting a USB memory device enables you to enjoy music from the vehicle speakers.
Select “USB” on the “Select Audio Source” screen.
Connecting a USB memory device
Audio control screen
“Select Audio Source” screen appears
Displaying the folder list
(
P. 258)
Random playback
Repeat play
Pause
Select to resume playback
Setting the sound (
276
3-2. Using the multimedia system
■ USB memory functions
● Depending on the USB memory device that is connected to the system, the device itself may not be operable and certain functions may not be available. If the device is inoperable or a function is unavailable due to a malfunction (as opposed to a system specification), disconnecting the device and reconnecting it may resolve the problem.
● If the USB memory device still does not begin operation after being disconnected and reconnected, format the memory.
■ Error messages for USB memory
Message
“Connection error. Please consult your Owner’s
Manual for instructions on how to connect the USB device.”
Cause/Correction procedures
This indicates a problem with the USB memory device or its connection.
“There are no file available for playback. Please add compatible file to your USB device.”
This indicates that no MP3/WMA/AAC files are included on the USB memory device.
■ USB memory
● Compatible devices
USB memory device that can be used for MP3, WMA and AAC playback.
● Compatible device formats
The following device format can be used:
• USB communication format: USB2.0 FS (12 Mbps), USB2.0 HS (480
Mbps)
• File system format: FAT16/32 (Windows)
• Correspondence class: Mass storage class
MP3, WMA and AAC files written to a device with any format other than those listed above may not play correctly, and their file names and folder names may not be displayed correctly.
3
277
3-2. Using the multimedia system
Items related to standards and limitations are as follows:
• Maximum directory hierarchy: 8 levels
• Maximum number of folders in a device: 3000 (including the root)
• Maximum number of files in a device: 9999
• Maximum number of files per folder: 255
● MP3, WMA and AAC files
MP3 (MPEG Audio LAYER 3) is a standard audio compression format.
Files can be compressed to approximately 1/10 of their original size using
MP3 compression.
WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format.
AAC is short for Advanced Audio Coding and refers to an audio compression technology standard used with MPEG2 and MPEG4.
MP3, WMA and AAC file and media/formats compatibility are limited.
● MP3 file compatibility
• Compatible standards
MP3 (MPEG1 AUDIO LAYER3, MPEG2 AUDIO LAYER3)
• Compatible sampling frequencies
MPEG1 AUDIO LAYER3: 32, 44.1, 48 (kHz)
MPEG2 AUDIO LAYER3: 16, 22.05, 24 (kHz)
• Compatible bit rates (compatible with VBR)
MPEG1 AUDIO LAYER3: 32-320 (kbps)
MPEG2 AUDIO LAYER3: 8-160 (kbps)
• Compatible channel modes: stereo, joint stereo, dual channel and monaural
● WMA file compatibility
• Compatible standards
WMA Ver. 7, 8, 9
• Compatible sampling frequencies
HIGH PROFILE 32, 44.1, 48 (kHz)
• Compatible bit rates
HIGH PROFILE 48-320 (kbps, VBR)
278
3-2. Using the multimedia system
● AAC file compatibility
• Compatible standards
MPEG4/AAC-LC
• Compatible sampling frequencies
11.025/12/16/22.05/24/32/44.1/48 (kHz)
• Compatible bit rates
16-320 (kbps)
• Compatible channel modes: 1 ch and 2 ch
● File names
The only files that can be recognized as MP3/WMA/AAC and played are those with the extension .mp3 or .wma.
● ID3, WMA and AAC tags
ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc.
The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags.
(The number of characters is based on ID3 Ver. 1.0 and 1.1.)
WMA tags can be added to WMA files, making it possible to record the track title and artist name in the same way as with ID3 tags.
AAC tags can be added to AAC files, making it possible to record the track title and artist name in the same way as with ID3 tags.
● MP3, WMA and AAC playback
• When a device containing MP3, WMA and AAC files is connected, all files in the USB memory device are checked. Once the file check is finished, the first MP3, WMA and AAC file is played. To make the file check finish more quickly, we recommend that you do not include any files other than MP3, WMA and AAC files or create any unnecessary folders.
• When a USB memory device is connected and the audio source is changed to USB memory mode, the USB memory device will start playing the first file in the first folder. If the same device is removed and reconnected (and the contents have not been changed), the USB memory device will resume play from the same point in which it was last used.
● Extensions
If the file extensions .mp3, .wma and .m4a are used for files other than
MP3, WMA and AAC files, they will be skipped (not played).
3
279
3-2. Using the multimedia system
● Playback
• To play MP3 files with steady sound quality, we recommend a fixed bit rate of at least 128 kbps and a sampling frequency of 44.1 kHz.
• There is a wide variety of freeware and other encoding software for
MP3, WMA and AAC files on the market, and depending on the status of the encoding and the file format, poor sound quality or noise at the start of playback may result. In some cases, playback may not be possible at all.
• Microsoft, Windows, and Windows Media are the registered trademarks of Microsoft Corporation in the U.S.A. and other countries.
CAUTION
■ While driving
Do not connect a USB memory device or operate the device controls.
NOTICE
■ To prevent damage to the USB memory device or its terminals
● Do not leave the USB memory device in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the USB memory device.
● Do not push down on or apply unnecessary pressure to the USB memory device while it is connected.
● Do not insert foreign objects into the port.
280
3-2. Using the multimedia system
Using the AUX port
To use the AUX port, connect a portable player, then select “AUX” on the “Select Audio Source” screen.
Connecting a portable audio player
■
Operating portable audio players connected to the multimedia system
The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio player itself.
■
When using a portable audio player connected to the power outlet
Noise may occur during playback. Use the power source of the portable audio player.
3
CAUTION
■
While driving
Do not connect a portable audio player or operate the device controls.
281
3-2. Using the multimedia system
Connecting Bluetooth
®
The following can be performed using Bluetooth
®
wireless communication:
■
A portable audio player can be operated and listened to via multimedia system
■
Hands-free phone calls can be made via a cellular phone
In order to use wireless communication, register and connect a
Bluetooth
®
device by performing the following procedures.
282
3-2. Using the multimedia system
Device registration/connection flow
1. Register the Bluetooth
® system (
P. 285, 286)
device to be used with Multimedia
2. Connect the Bluetooth
®
device to be used
(
P. 288)
To be used for audio To be used for hands-free phone
3. Start Bluetooth
® connection (
P. 288)
3. Start Bluetooth
® connection (
P. 288)
3
4. Check connection status
(
P. 304)
4. Check connection status
(
P. 306)
5. Use Bluetooth
®
audio
(
P. 304)
5. Use Bluetooth
®
phone
(
P. 305)
283
3-2. Using the multimedia system
Registering and connecting from the “Bluetooth Setup” screen
To display the screen shown below, press the “SETUP” button and select “Bluetooth” on the “Setup” screen.
Select to connect the device to be used with multimedia system. (
P. 288)
Select to register a Bluetooth
® device to be used with multimedia system. (
P. 286)
Select to set detailed
Bluetooth
®
system settings.
(
P. 291)
Select to delete registered devices. (
P. 287)
284
3-2. Using the multimedia system
Registering a Bluetooth
®
audio player for the first time
To use the Bluetooth
®
Audio, it is necessary to register an audio player with the system.
Once the player has been registered, it is possible to use the
Bluetooth
®
Audio.
This operation cannot be performed while driving.
For details about registering a Bluetooth
®
device (
P. 286)
Turn the Bluetooth
®
connection setting of your audio player on.
This function is not available when the Bluetooth
®
connection setting of your audio player is set to off.
Press the “AUDIO” button.
Select “ Audio” on the “Select Audio Source” screen.
Select “Select Device”.
Follow the steps in “How to register a Bluetooth
®
device” from
“STEP 2”. (
P. 286)
3
Registering a Bluetooth
®
phone for the first time
To use the hands-free system, it is necessary to register a Bluetooth
® phone with the system.
Once the phone has been registered, it is possible to use the handsfree system.
For details about registering a Bluetooth
®
device (
P. 286)
Turn the Bluetooth
®
connection setting of your cellular phone on.
Press the button.
Select “OK” to register a phone.
Follow the steps in “How to register a Bluetooth
®
device” from
“STEP 2”. (
P. 286)
285
3-2. Using the multimedia system
Registering a Bluetooth
®
device
Bluetooth
®
compatible phones (HFP) and portable audio players
(AVP) can be registered simultaneously. You can register up to 5
Bluetooth
®
devices.
■
How to register a Bluetooth
®
device
Display the “Bluetooth Setup” screen. (
P. 284)
Select “Add”.
When this screen is displayed, search for the device name displayed on this screen on the screen of your Bluetooth
® device.
For details about operating the
Bluetooth
®
device, see the manual that comes with it.
To cancel the registration, select
“Cancel”.
Register the Bluetooth
®
device using your Bluetooth
®
device.
A PIN-code is not required for SSP (Secure Simple Pairing) compatible Bluetooth
®
devices. Depending on the type of Bluetooth
®
device being connected, a message confirming registration may be displayed on the Bluetooth
®
device’s screen. Respond and operate the
Bluetooth
®
device according to the confirmation message.
Check that this screen is displayed when registration is complete.
286
3-2. Using the multimedia system
Select “OK” when the connection status changes from “Connecting...” to “Connected”.
If an error message is displayed, follow the guidance on the screen to try again.
Registration can be performed from screens other than the
“Bluetooth Setup” screen.
■ When registering from the “Bluetooth Audio” screen
Display the “Bluetooth Audio” screen. (
P. 257)
Select “Select Device”.
Follow the steps in “How to register a Bluetooth
®
device” from
“STEP 2”. (
P. 286)
■ Deleting a Bluetooth
®
device
Display the “Bluetooth Setup” screen. (
P. 284)
Select “Remove”.
Select the desired device.
A confirmation message will be displayed, select “Yes” to delete the device.
Check that a confirmation screen is displayed when the operation is complete.
3
287
3-2. Using the multimedia system
Connecting a Bluetooth
®
device
Up to 5 Bluetooth
®
devices (Phones (HFP) and audio players (AVP)) can be registered.
If more than 1 Bluetooth
®
device has been registered, select which device to connect to.
Press the “SETUP” button.
Select “Bluetooth” on the “Setup” screen.
Select the device to be connected.
Supported profile icons will be displayed.
Phone
Audio player
Supported profile icons for currently connected devices will illuminate.
Dimmed icons can be selected to connect to the function directly.
■ Auto connection
To turn auto connection mode on, set “Bluetooth Power” to on.
(
P. 291)
When you register a phone, auto connection will be activated.
Always set it to this mode and leave the Bluetooth
®
phone in a place where a connection can be established.
When the engine switch is turned to the “ACC” or “ON” position, the system will search for a nearby cellular phone you have registered.
Next, the system automatically connects with the most recent of the phones connected to in the past. Then, the connection result is displayed.
288
3-2. Using the multimedia system
■
Manual connection
When auto connection has failed or “Bluetooth Power” is turned off, you must connect the Bluetooth
®
device manually.
Follow the steps in “Connecting a Bluetooth
®
device” from
“STEP 1”. (
■
Connecting a Bluetooth
®
audio player
Registering an additional device
Select “Select Device” on the “Bluetooth Audio” screen.
For more information:
P. 286
Selecting a registered device
Select “Select Device” on the “Bluetooth Audio” screen.
For more information:
P. 288
3
■ Reconnecting a Bluetooth
®
phone
If the system cannot connect due to poor signal strength with the engine switch in the “ACC” or “ON” position, the system will automatically attempt to reconnect.
If the phone is turned off, the system will not attempt to reconnect. In this case, the connection must be made manually, or the phone must be reselected.
289
3-2. Using the multimedia system
Displaying a Bluetooth
®
device details
You can confirm and change the registered device details.
■ Bluetooth
®
device registration status
Display the “Bluetooth Setup” screen. (
P. 284)
Select the device.
Select “Device Info”.
Following screen is displayed:
Device name
Change connection method
(
Bluetooth
®
address
Display your telephone number
The number may not be displayed depending on the model of phone.
Compatibility profile of the device
Restore default settings
■ Changing connection method
Select “Connect Audio Player from”.
Select “Vehicle” or “Device”.
“Vehicle”: Connect the multimedia system to the portable audio player.
“Device”: Connect the portable audio player to the multimedia system.
290
3-2. Using the multimedia system
Detailed Bluetooth
®
system settings
You can confirm and change the detailed Bluetooth
®
settings.
■ How to check and change detailed Bluetooth
®
settings
Display the “Bluetooth Setup” screen. (
P. 284)
Select “System Settings”.
The following screen is displayed:
Bluetooth
®
power on/off
You can change Bluetooth
®
function on/off
Bluetooth
®
name
Change PIN-code (
P. 291)
Bluetooth
®
address
Display phone status
You can set the system to show the status confirmation display when connecting a telephone
Display audio player status
You can set the system to show the status confirmation display when connecting an audio player
Compatibility profile of the system
Restore default settings
■ Editing the Bluetooth
®
PIN
You can change the PIN-code that is used to register your
Bluetooth
®
devices in the system.
Select “Bluetooth
®
PIN”.
Input a PIN-code, and select “OK”.
3
291
3-2. Using the multimedia system
What to do if... (Troubleshooting)
If there is a problem with the hands-free system or a Bluetooth
® device, first check the table below.
When using the hands-free system with a Bluetooth
®
device
Symptom
The hands-free system or Bluetooth
®
device does not work.
Likely cause
The connected device may not be a compatible
Bluetooth
®
cellular phone.
The Bluetooth
®
version of the connected cellular phone may be older than the specified version.
Solution
For a list of specific devices which operation has been confirmed on this system, check with your Toyota dealer or the following website: http://www.toyota.com/ bluetooth
Use a cellular phone with
Bluetooth
®
version 2.0 or higher (recommended:
Ver. 3.0 with EDR or higher). (
292
3-2. Using the multimedia system
When registering/connecting a cellular phone
Symptom
A cellular phone cannot be registered.
A Bluetooth
® connection cannot be made.
“Please check your device settings.” message is displayed.
Likely cause
An incorrect passcode was entered on the cellular phone.
The registration operation has not been completed on the cellular phone side.
Old registration information remains on either this system or the cellular phone.
Another Bluetooth device is already connected.
®
Bluetooth
®
function is not enabled on the cellular phone.
Bluetooth
®
function is not enabled on the cellular phone.
Solution
Enter the correct passcode on the cellular phone.
Complete the registration operation on the cellular phone (approve registration on the phone).
Delete the existing registration information from both this system and the cellular phone, then register the cellular phone you wish to connect to this system. (
P. 287)
Manually connect the cellular phone you wish to use to this system.
(
P. 289)
Enable the Bluetooth function on the cellular phone.
® function on the cellular phone.
Enable the Bluetooth
®
Old registration information remains on either this system or the cellular phone.
Delete the existing registration information from both this system and the cellular phone, then register the cellular phone you wish to connect to this system. (
P. 287)
3
293
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement