3-2. Using the multimedia system
In other situations
Symptom Likely cause
The cellular phone is not close enough to this system.
Solution
Bring the cellular phone closer to this system.
Even though all conceivable measures have been taken, the symptom status does not change.
The cellular phone is the most likely cause of the symptom.
• Turn the cellular phone off, remove and reinstall the battery pack, and then restart the cellular phone.
• Enable the cellular phone’s Bluetooth
®
connection.
• Stop the cellular phone’s security software and close all applications.
• Before using an application installed on the cellular phone, carefully check its source and how its operation might affect this system.
296
3-2. Using the multimedia system
Bluetooth
®
■ About Bluetooth
®
The Bluetooth
®
word mark and logos are registered trademarks owned Bluetooth
SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Other trademarks and trade names are those of their respective owners.
■ When using the Bluetooth
®
audio system
● In the following conditions, the system may not function.
• If the portable audio player is turned off
• If the portable audio player is not connected
• If the portable audio player’s battery is low
● There may be a delay if a cellular phone connection is made during
Bluetooth
®
audio play.
● Depending on the type of portable audio player that is connected to the system, operation may differ slightly and certain functions may not be available.
■ When using the hands-free system
● The multimedia system is muted when making a call.
● If both parties speak at the same time, it may be difficult to hear.
● If the received call volume is overly loud, an echo may be heard.
If the Bluetooth
®
phone is too close to the system, quality of the sound may deteriorate and connection status may deteriorate.
● In the following circumstances, it may be difficult to hear the other party:
• When driving on unpaved roads
• When driving at high speeds
• If a window is open
• If the air conditioning is blowing directly on the microphone
• If there is interference from the network of the cellular phone
3
297
3-2. Using the multimedia system
■ Conditions under which the system will not operate
● If using a cellular phone that does not support Bluetooth
®
● If the cellular phone is turned off
● If you are outside of cellular phone service coverage
● If the cellular phone is not connected
● If the cellular phone’s battery is low
● When outgoing calls are controlled, due to heavy traffic on telephone lines, etc.
● When the cellular phone itself cannot be used
● When transferring contact data from the cellular phone
■ Bluetooth
®
antenna
The antenna is built into the display.
If the portable audio player is behind the seat or in the glove box or console box, or is touching or covered by metal objects, the connection status may deteriorate.
If the cellular phone is behind the seat or in the console box, or touching or covered by metal objects, the connection status may deteriorate.
■ Battery charge/signal status
● This display may not correspond exactly with the portable audio player or cellular phone itself.
● This system does not have a charging function.
● The portable audio player or cellular phone battery will be depleted quickly when the device is connected to Bluetooth
®
.
■ When using the Bluetooth
®
audio and hands-free system at the same time
The following problems may occur.
● The Bluetooth
®
audio connection may be interrupted.
● Noise may be heard during Bluetooth
®
audio playback.
298
3-2. Using the multimedia system
■ About the contact in this system
The following data is stored for every registered cellular phone. When another phone is connecting, you cannot read the registered data.
● Contact data
● Call history
● Favorite
● Message
When removing a Bluetooth
®
phone from the system, the above-mentioned data is also deleted.
■ Compatible models
The Bluetooth
®
audio system supports portable audio players with the following specifications
● Bluetooth
®
specifications:
Ver. 2.0, or higher (Recommended: Ver. 3.0+EDR or higher)
● Profiles:
• A2DP (Advanced Audio Distribution Profile) Ver. 1.0, or higher
(Recommended: Ver. 1.2 or higher)
This is a profile to transmit stereo audio or high quality sound to the multimedia system.
• AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher
(Recommended: Ver. 1.4 or higher)
This is a profile to allow remote control the A/V equipment.
However, please note that some functions may be limited depending on the type of portable audio player connected.
The hands-free system supports cellular phones with the following specifications.
• Bluetooth
®
specification:
Ver. 2.0 or higher (Recommended: Ver. 3.0+EDR or higher)
3
299
3-2. Using the multimedia system
● Profiles:
• HFP (Hands Free Profile) Ver. 1.0 or higher (Recommended: Ver. 1.6
or higher)
This is a profile to allow hands-free phone calls using a cellular phone or head set. It has outgoing and incoming call functions.
• OPP (Object Push Profile) Ver. 1.1 or higher (Recommended: Ver. 1.2)
This is a profile to transfer contact data. When a Bluetooth
®
compatible cellular phone has both PBAP and OPP, OPP cannot be used.
• PBAP (Phone Book Access Profile) Ver. 1.0 or higher (Recommended:
Ver. 1.1)
This is a profile to transfer contact data.
If the cellular phone does not support HFP, you cannot register it with the hands-free system. OPP, PBAP services must be selected individually.
■ Certifications for the Bluetooth
®
For vehicles sold in U.S.A.
FCC ID: ACJ932YEAP01A446
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For vehicles sold in Canada
IC: 216J-YEAP01A446
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
300
3-2. Using the multimedia system
The latest original “DECLARATION of CONFORMITY” (DoC) is available at the address stated.
http://www.ptc.panasonic.de/
3
301
