Detachable pole antenna. Toyota Tacoma, 2015, Tacoma 2015, 2015 Tacoma
જાહેરાત
જાહેરાત
3-2. Using the multimedia system
■
Registering a new contact to the contact list
New contact data can be registered. Up to 4 numbers per person can be registered. For PBAP compatible Bluetooth
®
phones, this function is available when “Automatic Contact/History Transfer” is set to off. (
P. 322)
Select “New Contact”.
Enter the name and select “OK”.
Enter the phone number and select “OK”.
Select the phone type for the phone number.
To add another number to this contact, select “Yes”.
● Registering a new contact in a different way (From the “Call History” screen)
Display the phone screen. (
P. 305)
Select the “Call History” tab and select a contact not yet registered in the contact list.
Select “Add to Contacts”.
Follow the steps in “Registering a new contact to the contact list” from “STEP 3”. (
P. 325)
■
Editing the contact data
For PBAP compatible Bluetooth
®
phones, this function is available when “Automatic Contact/History Transfer” is set to off. (
P. 322)
Select “Edit Contact”.
Select the desired contact.
Select corresponding to the desired name or number.
For editing the name
Follow the steps in “Registering a new contact to the contact list” from “STEP 3”. (
P. 325)
For editing the number
Follow the steps in “Registering a new contact to the contact list” from “STEP 4”. (
P. 325)
3
325
3-2. Using the multimedia system
● Editing the contacts in a different way (From the “Contact Details” screen)
Display the phone screen. (
P. 305)
Select the “Contacts”, “Call History” tab or the “Favorites” tab and select the desired contact.
Select “Edit Contact”.
“E-mail Addresses”: Select to display all registered e-mail addresses for the contact.
Follow the steps in “Editing the contact data” from “STEP 4”.
(
P. 325)
■ Deleting the contact data
For PBAP compatible Bluetooth
®
phones, this function is available when “Automatic Contact/History Transfer” is set to off. (
P. 322)
Select “Delete Contacts”.
Select the desired contact and select “Delete”.
Select “Yes” when the confirmation screen appears.
● Deleting the contact in a different way (From the “Contact Details” screen)
Display the phone screen. (
P. 305)
Select the “Contacts”, “Call History” tab or the “Favorites” tab and select the desired contact.
Select “Edit Contact”.
Select “Yes” when the confirmation screen appears.
326
3-2. Using the multimedia system
■
Favorites list setting
Up to 15 contacts (maximum of 4 numbers per contact) can be registered in the favorites list.
● Registering the contacts in the favorites list
Select “Add Favorite”.
Select the desired contact to add to the favorites list.
Dimmed contacts are already stored as a favorite.
Check that a confirmation screen is displayed when the operation is complete.
When 15 contacts have already been registered to the favorites list
When 15 contacts have already been registered to the favorites list, a registered contact needs to be replaced.
Select “Yes” when the confirmation screen appears to replace a contact.
Select the contact to be replaced.
Check that a confirmation screen is displayed when the operation is complete.
Registering contacts in the favorites list in a different way (from the
“Contacts” screen)
Display the phone screen. (
P. 305)
Select the “Contacts” tab.
Select at the beginning of the desired contact list name to be registered in the favorites list.
When selected, is changed to , and the contact is registered in the favorites list.
3
327
3-2. Using the multimedia system
Registering contacts in the favorites list in a different way (from the
“Contact Details” screen)
Display the phone screen. (
P. 305)
Select the “Contacts” tab or the “Call History” tab and select the desired contact.
Select “Add Favorite”.
Check that a confirmation screen is displayed when the operation is complete.
● Deleting the contacts in the favorites list
Select “Remove Favorite”.
Select the desired contacts and select “Remove”.
Select “Yes” when the confirmation screen appears.
Check that a confirmation screen is displayed when the operation is complete.
Deleting contacts in the favorites list in a different way (from the
“Contacts” screen)
Display the phone screen. (
P. 305)
Select the “Contacts” tab.
Select at the beginning of the contact list name to be deleted from the favorites. list.
When selected, is changed to , and the data is deleted from the list.
Deleting contacts in the favorites list in a different way (from the
“Contact Details” screen)
Display the phone screen. (
P. 305)
Select the “Contacts”, “Call History” tab or the “Favorites” tab and select the desired contact to delete.
Select “Remove Favorite”.
Select “Yes” when the confirmation screen appears.
Check that a confirmation screen is displayed when the operation is complete.
328
3-2. Using the multimedia system
■
Message Settings
Display the “Phone/Message Settings” screen. (
P. 320)
Select “Messaging Settings”.
Select the desired item to be set.
Set automatic message transfer on/off.
Set automatic message readout on/off.
Set the SMS/MMS notification popup on/off.
Set the e-mail notification popup on/off.
Set adding the vehicle signature to outgoing messages on/ off.
Set updating message read status on phone on/off.
Change the incoming SMS/
MMS display.
“Full Screen”: When an SMS/
MMS message is received, the incoming SMS/MMS display screen is displayed and can be operated on the screen.
“Drop-Down”: When an SMS/
MMS message is received, a message is displayed on the upper side of the screen.
3
329
3-2. Using the multimedia system
Change the incoming e-mail display.
“Full Screen”: When an e-mail is received, the incoming e-mail display screen is the displayed and can be operated on the screen.
“Drop-Down”: When an e-mail is received, a message is displayed on the upper side of the screen.
Set display of messaging account names on the inbox tab on/off.
When set to on, messaging account names used on the cellular phone will be displayed.
● Displaying the “Messaging Settings” screen in a different way
Display the phone screen. (
P. 305)
Select .
Select “Settings”.
■
To return to the default settings
Select “Default”, and then “Yes”.
330
3-2. Using the multimedia system
■
Phone Display Settings
Display the “Phone/Message Settings” screen. (
P. 320)
Select “Phone Display Settings”.
Select the desired item to be set.
Change the incoming call display.
“Full Screen”: When a call is received, the hands-free screen is displayed and can be operated on the screen.
“Drop-Down”: A message is displayed on the upper side of the screen.
Set display of the contact/history transfer completion message on/off.
3
331
3-2. Using the multimedia system
Voice command system
The voice command system enables the hands-free system to be operated using voice commands.
Operations of the voice command system can be performed by selecting the menu corresponding to each function on the screen.
Even if any menu is selected, commands displayed on all menus can be operated.
■ Using the voice command system
Press the talk switch.
To cancel the voice command system, press and hold the talk switch.
After a beep sounds, say the desired command.
On the list screen, you can select the desired command.
■ Microphone
P. 306
■ When using the microphone
● It is unnecessary to speak directly into the microphone when giving a command.
● It is not necessary to wait for the confirmation beep before speaking a command.
332
3-2. Using the multimedia system
● Voice commands may not be recognized if:
• Spoken too quickly.
• Spoken at a low or high volume.
• The roof or windows are open.
• Passengers are talking while voice commands are spoken.
• The air conditioning speed is set high.
• The air conditioning vents are turned towards the microphone.
● In the following conditions, the system may not recognize the command properly and using voice commands may not be possible:
• The command is incorrect or unclear. Note that certain words, accents or speech patterns may be difficult for the system to recognize.
• There is excessive background noise, such as wind noise.
■
Casual speech recognization
Due to natural language speech recognition technology, this system enables recognition of a command when spoken naturally. However, the system cannot recognize every variation of each command.
In some situations, it is possible to omit the command for the procedure and directly state the desired operation.
Not all voice commands are displayed in the short cut menu.
This function is available in English, Spanish and French.
● Expression examples for each function
3
Command
“Call <name>
<type>”
“Dial <number>”
Expression examples
Get me <Robert Brown>.
I need to call <Robert Brown> at <Work> right away.
Please dial the number <3334445555>.
Ring <3334445555>.
333
3-2. Using the multimedia system
Operating the sub woofer (on some Access Cab models)
OFF
ON
LIGHT ON
The sub woofer illumination turns on. In this position, the sub woofer operates.
334
3-2. Using the multimedia system
Detachable pole antenna
The antenna can be removed.
■
Removing the antenna
Place the included wrench around the antenna.
When not in use, the wrench is stored in glove box.
Loosen the antenna with the wrench and remove it.
3
335
3-2. Using the multimedia system
■
Installing the antenna
Tighten the antenna by one hand until it will not turn any more.
Using the wrench, tighten the antenna an additional 1/8th turn (20 to 45 degrees) to secure it in place.
After tightening the antenna, remove the wrench.
■
About the wrench
● A standard 5/16 in. (8 mm) wrench can also be used to install or remove the antenna.
●
After using the included wrench, store it in the glove box for safekeeping.
336
3-2. Using the multimedia system
NOTICE
■ To avoid damaging the antenna
Remove the antenna in the following situations.
● When using an automatic carwash.
● When the antenna will touch the ceiling of a garage, etc.
● When covering the vehicle with a car cover.
■ Removing the antenna
● For normal driving, make sure the antenna is installed.
● When removing the antenna to use an automatic carwash, etc., be careful not to lose the antenna. Also, make sure to reinstall the antenna before driving the vehicle.
■ Using the wrench
● When installing or removing the antenna, use the included wrench or a standard 5/16 in. (8 mm) wrench.
● Be careful not to scratch or damage the vehicle body with the wrench.
● Do not over-tighten the antenna.
Over-tightening may damage the antenna.
● Do not use pliers to install or remove the antenna.
Pliers may damage the antenna’s finish.
3
337
3-3. Using the interior lights
Interior lights list
Interior light (
Personal lights (
■ Illuminated entry system
When the interior light switch is in the DOOR position, the interior light automatically turns on/off according to whether the doors are locked/unlocked and whether the doors are open/closed.
■ To prevent the battery from being discharged
If the interior light remains on when the door is not fully closed and the interior light switch is in the DOOR position, the light will go off automatically after 20 minutes.
338
Interior light
Personal lights
3-3. Using the interior lights
Interior light and personal lights
DOOR position
OFF
ON
3
On/off
339
3-4. Using the storage features
List of storage features
Glove box
Overhead console
Bottle holders
Auxiliary boxes
Front console box
Cup holders
CAUTION
■ Items that should not be left in the storage spaces
Do not leave glasses, lighters or spray cans in the storage spaces, as this may result in the following when cabin temperature becomes high:
● Glasses may be deformed by heat or cracked if they come into contact with other stored items.
● Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.
340
Glove box
3-4. Using the storage features
Glove box and front console box
Pull up the lever.
CAUTION
■ Caution while driving
Keep the glove box closed. In the event of sudden braking or sudden swerving, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.
3
Front console box
Push the button.
CAUTION
■ Caution while driving
Keep the console box closed.
Injuries may result in the event of an accident or sudden braking.
341
3-4. Using the storage features
Cup holders
Vehicles with an automatic transmission
Cup holders
Vehicles with a manual transmission
342
3-4. Using the storage features
Cup holders
■ Removing the cup holder (vehicles with an automatic transmission)
Pull the cup holder up.
CAUTION
■ Items unsuitable for the cup holder
Do not place anything other than cups or aluminum cans in the cup holders.
Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.
3
343
3-4. Using the storage features
Bottle holders
Front
Front console box
Rear (Double Cab models)
Bottle holders
■ Bottle holders
Depending on their size or shape, some bottles may not fit in the holders.
344
3-4. Using the storage features
Bottle holders and auxiliary boxes
NOTICE
■ Items that should not be stowed in the bottle holders
Put the cap on before stowing a bottle. Do not place open bottles in the bottle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
Auxiliary boxes
Front
Pull the lid down.
3
Rear (Access Cab models [vehicles without rear seats])
345
3-4. Using the storage features
Auxiliary boxes
Under the rear seats (Access Cab models [vehicles with rear seats])
Pull up the lever.
Raise the bottom cushion up.
Turn the knob counterclockwise.
Open the lid.
Press the lid against the bottom of the lower cushion until it is supported by the hookand-loop fastener.
Make sure that the lid is supported to prevent it from closing unexpectedly.
346
3-4. Using the storage features
Auxiliary boxes
Under the rear seats (Double Cab models)
Swing the bottom cushion up by pulling the lock release strap.
Turn the knob counterclockwise.
Open the lid.
3
CAUTION
■
Caution while driving
Keep the auxiliary boxes closed and locked.
Injuries may result in the event of an accident or sudden braking.
■ Auxiliary box (Access cab models [vehicles without rear seat])
Never let anyone sit on the auxiliary box. Doing so may damage the auxiliary box and cause injury. In addition, it may cause death or severe injury in the event of sudden braking, sudden swerving or an accident.
347
3-4. Using the storage features
Overhead console
Overhead console
The overhead console is useful for temporarily storing sunglasses and similar small items.
Pull the lid down while pushing the knob.
CAUTION
■
Caution while driving
Keep the overhead console closed.
Injuries may result in the event of an accident or sudden braking.
■
Items unsuitable for storing
Do not store items heavier than 0.4 lb. (0.2 kg).
Doing so may cause the overhead console to open and the items inside may fall out, resulting in an accident.
348
3-5. Other interior features
Sun visors
Type A
Forward position:
Flip down.
Side position:
Flip down, unhook, and swing to the side.
3
Type B
Forward position:
Flip down.
Side position:
Flip down, unhook, and swing to the side.
Side extender:
Place in side position, then slide backwards.
349
3-5. Other interior features
Vanity mirrors
Vehicles without vanity light
Vehicles with vanity light
Slide the cover.
The light turns on when the cover is opened.
350
3-5. Other interior features
Clock
The clock is displayed on the screen.
■
Setting the clock
Vehicles with Entune Audio (Multimedia system types:
Vehicles with Entune Audio Plus or Entune Premium Audio
(Multimedia system types:
Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.
3
■ The clock is displayed when
The engine switch is in the ACC or ON position.
■ When disconnecting and reconnecting battery terminals
The clock data will be reset.
351
3-5. Other interior features
Power outlets (12 VDC)
Please use as a power supply for electronic goods that use less than
12 VDC/10 A (power consumption of 120 W).
When using electronic goods, make sure that the power consumption of all the connected power outlets is less than 120 W.
■
The power outlets can be used when
The engine switch is in the ACC or ON position.
NOTICE
■
To avoid damaging the power outlets
Close the power outlets lid when not in use.
Foreign objects or liquids that enter the power outlets may cause a short circuit.
■
To prevent the battery from being discharged
Do not use the power outlets longer than necessary when the engine is not running.
352
3-5. Other interior features
Power outlet (120 VAC)
The power outlet can be used for electrical appliances.
Main switch
To use the power outlet, turn on the main switch.
The power supply starts a few seconds after the main switch is pressed.
Power outlet socket
Maximum available capacity of the power outlet
■ While the vehicle is being driven
The maximum capacity of the power outlet is always
120 VAC/100 W.
■ When the vehicle is stationary
The maximum capacity of the power outlet varies depending on the following conditions.
● The maximum capacity is 120 VAC/400 W when the following condition applies:
• The shift lever is in P or N. (automatic transmission)
: If equipped
353
3
3-5. Other interior features
• The shift lever is in N and the clutch pedal is not depressed.
(manual transmission)
A maximum capacity of 400W can only be restored by turning the power outlet main switch off and then on again under condition described above.
● The maximum capacity is 120 VAC/100 W when the following condition applies:
• The shift lever is moved to any positions other than P and N.
(automatic transmission)
• The clutch pedal is depressed. (manual transmission)
■ The power outlet can be used when
The engine is started.
■ The indicator light changes according the maximum available capacity, as follows:
Indicates 120 VAC/400 W
Indicates 120 VAC/100 W
■ When the power outlet is in operation
The sound of the cooling fan may be heard from the front console box. This is normal and does not indicate a malfunction.
■ If the engine is started with the power outlet main switch on
The maximum capacity of the power supply may decrease to below the standard, or may be cut off completely, even when the vehicle is stationary.
354
3-5. Other interior features
■ The protection circuit may be activated to cut the power supply if any of the following conditions apply:
● The engine is started with the power outlet main switch on.
● Use of electrical appliances exceeding the maximum capacity is attempted.
A sound may be heard when the protection circuit is activated.
This is normal and does not indicate a malfunction.
● Electrical appliances, which consume power exceeding 100 W, have been used continuously for a long time period.
● The total power usage by all electrical features (headlights, air conditioning, etc.) has exceeded the total vehicle maximum for an extended period of time.
■ If the protection circuit is activated and the power supply is cut, conduct the following procedure:
Park the vehicle in a safe place, and then securely apply the parking brake.
Check and ensure the following conditions:
• The shift lever is in P or N. (automatic transmission)
• The shift lever is in N and the clutch pedal is not depressed.
(manual transmission)
Make sure that the power consumption of the electric appliance is within the maximum capacity of the power outlet and the appliance is not broken.
Press the power outlet main switch again.
When the cabin temperature is high, open the windows to cool the temperature down. Once it reaches the normal temperature, turn the power outlet main switch on again.
If the power supply is not resumed even after performing the above procedure, have the vehicle inspected by a Toyota dealer.
3
355
3-5. Other interior features
CAUTION
■ Using a power outlet
Observe the following precautions to reduce the risk of injury.
● Use of the power outlet when it is wet with rain, drinks water or snow may result in electrical shocks and is extremely dangerous. The power outlet must be thoroughly dried before use.
● Do not allow children to use or play with the power outlet.
● Be careful not to get any part of your body caught in the power outlet lid.
● When using electrical appliances, strictly follow any cautions and notices written on their labels and in the manufacturers’ instruction manuals.
● Do not modify, disassemble or repair the power outlet or its inverter, in any way. Doing so may result in unexpected malfunctions or accidents, which could cause serious damage or injuries. Contact a Toyota dealer for any necessary repairs.
■ To prevent injuries and accidents, securely fix all electric appliances before use and do not use any appliances that may do any of the following:
● Distract the driver while driving, or hamper safe driving.
● Result in a fire or burn injuries due to the appliance rolling, falling or overheating while driving.
● Emit steam, while the windows of the cabin are closed.
■ To prevent unexpected accidents, such as electric shocks, do not perform any of the following
● Using the power outlet for electric heaters while sleeping.
● Contaminating the power outlet with liquid substances or mud.
● Handling electrical appliance plugs at the power outlet with wet hands or feet.
● Inserting foreign objects into the power outlet.
● Using malfunctioning electric appliances.
● Inserting inappropriate or badly fitting plugs into the power outlet.
356
3-5. Other interior features
NOTICE
■ To avoid damaging the power outlet and the plug
● Close the power outlet lid when not in use.
● Foreign objects or liquids that enter the power outlet may cause a short circuit.
● Do not use plug adaptors to connect too many plugs to the power outlet.
● After inserting a plug, gently close the power outlet lid.
■ To prevent the fuse from being blown
Do not use a 120 VAC appliance that requires more than maximum capacity.
If a 120 VAC appliance that consumes more than maximum capacity is used, the protection circuit will cut the power supply.
■ Appliances that may not operate properly (120 VAC)
The following 120 VAC appliances may not operate even if their power consumption is under maximum capacity.
● Appliances with high initial peak wattage
● Measuring devices that process precise data
● Other appliances that require an extremely stable power supply
■ To prevent the battery from being discharged
Turn off all the vehicle’s electronic equipment and accessories, such as the headlights and air conditioning, when electrical appliances that consume in excess of 100W are used continuously for long periods of time.
■ To prevent any damage caused by heat
● Do not use any electrical appliances that give off intense heat such as toasters, in any locations including the internal or external trim, seats and deck.
● Do not use any electrical appliances, which are easily affected by vibration or heat, inside the vehicle.
Vibration while driving, or the heat of the sun while parking, may result in damage to those electrical appliances.
3
357
3-5. Other interior features
NOTICE
■ If any electrical appliances are to be used while driving
Securely fasten both the appliances and their cables to prevent them from falling or getting caught any of the power train components.
■ If the power outlet is loose when an electrical appliance plug is connected
Replace the outlet.
Contact a Toyota dealer for any necessary replacements.
■ If the power outlet gets dirty
Turn the main switch off and use a soft, clean cloth to wipe it gently.
Do not use any cleansing materials, such as organic solvents, wax, or compound cleaners, as these may damage the power outlet or cause it to malfunction.
358
3-5. Other interior features
Seat heaters
On
The indicator comes on.
Adjusts the seat temperature.
The further you turn the dial upward, the warmer the seat becomes.
3
■
The seat heaters can be used when
The engine switch is in the ON position.
■
When not in use
Turn the dial fully downward. The indicator turns off.
: If equipped
359
3-5. Other interior features
CAUTION
■ Burns
● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns:
• Babies, small children, the elderly, the sick and the physically challenged
• Persons with sensitive skin
• Persons who are fatigued
• Persons who have taken alcohol or drugs that induce sleep (sleeping drugs, cold remedies, etc.)
● Do not cover the seat with anything when using the seat heater.
Using the seat heater with a blanket or cushion increases the temperature of the seat and may lead to overheating.
● Do not use the seat heater more than necessary.
Doing so may cause minor burns or overheating.
NOTICE
■ To prevent seat heater damage
Do not put heavy objects that have an uneven surface on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.
■ To prevent battery discharge
Turn the seat heaters off when the engine is not running.
360
3-5. Other interior features
Seatback table
Front passenger’s seatback can be used as a temporary table only when the vehicle is stopped.
Fold down the front passenger’s seat to use the seatback table. (
CAUTION
■ Caution while driving
Observe the following precautions to avoid death or serious injury.
● Do not set up the seatback table.
● Do not sit on or place anything on the seatback table.
NOTICE
■ To prevent damage to the seatback table
Do not put heavy loads on the table.
3
: If equipped
361
3-5. Other interior features
Floor mat
Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.
Insert the retaining hooks
(clips) into the floor mat eyelets.
*
Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
*
: Always align the marks.
The shape of the retaining hooks (clips) may differ from that shown in the illustration.
362
3-5. Other interior features
CAUTION
Observe the following precautions.
Failure to do so may cause the driver’s floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident.
■ When installing the driver’s floor mat
● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats.
● Only use floor mats designed for the driver’s seat.
● Always install the floor mat securely using the retaining hooks (clips) provided.
● Do not use two or more floor mats on top of each other.
● Do not place the floor mat bottom-side up or upside-down.
■ Before driving
● Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor.
● With the engine stopped and the shift lever in P (automatic transmission) or N
(manual transmission), fully depress each pedal to the floor to make sure it does not interfere with the floor mat.
3
363
3-5. Other interior features
Luggage compartment features
Behind the rear seat (Double Cab models only)
Cargo net hooks (vehicles with sub woofer)
Grocery bag hooks
Flashlight holder
Storage boxes
Deck
364
Auxiliary boxes
Tie-down cleats
Deck hooks
3-5. Other interior features
Auxiliary boxes
Left side
Turn the knob counterclockwise.
Open the lid.
Right side (vehicles without 120V power outlet)
Turn the knob counterclockwise.
Open the lid.
3
Right side (vehicles with 120V power outlet)
Turn the knob counterclockwise.
Open the lid.
365
3-5. Other interior features
CAUTION
■ Caution while driving
Keep the auxiliary boxes closed and locked.
Injuries may result in the event of an accident or sudden braking.
Deck hooks
Deck hooks are provided for securing loose items.
CAUTION
■
When not in use
Keep the deck hooks folded.
366
3-5. Other interior features
Tie-down cleats
The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load.
Locking plate
Thumb wheel
Tie-down cleat
3
■
Installing the tie-down cleat
0.5 in.
(12.7 mm)
Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the locking plate maintains 0.5 in.
(12.7 mm) gap.
Deck rail
Detent
Locking plate
367
3-5. Other interior features
Insert the locking plate into the deck rail, rotate the tie-down cleat 90°, and release the thumb wheel.
Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a detent.
Tighten the thumb wheel in a clockwise motion until the clutch mechanism ratchets.
Check the tie-down cleat to confirm that it is locked into a detent and securely mounted to the deck rail system.
368
3-5. Other interior features
CAUTION
■ Tie-down cleat precautions
● Properly install and tighten the tie-down cleats into the deck rail system.
Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehicle is in motion.
● Properly secure all cargo to prevent shifting or sliding during driving.
Failure to properly secure cargo can cause injury when the vehicle is in motion.
● Applying loads at an angle to the tie-down cleat greater than 45° or loads greater than 220 lb. (100 kg) may cause damage to the deck, deck rail system, tie-down cleat and/or the cargo.
● Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail.
● Do not install more than the following number of tie-down cleats per deck rail:
• Side rail:
Short deck—Max. 3 locations
Long deck—Max. 4 locations
• Headboard rail: Max. 3 locations
3
Storage boxes (Double Cab models only)
Storage box is designed to place things like bottles.
Right side (vehicles without sub woofer)
369
3-5. Other interior features
Left side
■ Removing the separator
Remove the separator.
It can be installed in various positions as required.
Flashlight holder (Double Cab models only)
Flashlight holder is designed to hold the flashlight securely.
370
3-5. Other interior features
■ Removing the flashlight holder
Remove the flashlight holder.
It can be installed in various positions as required.
Grocery bag hooks (Double Cab models only)
Grocery bag hook is designed to hang things like grocery bag.
3
NOTICE
■
Grocery bag hook weight capacity
Do not hang any object heavier than 7 lb. (3 kg) on the grocery bag hooks.
371
3-5. Other interior features
Cargo net hooks (Double Cab models with sub woofer)
Cargo net hooks are designed to hang the factory-supplied cargo net.
NOTICE
■ To prevent damage to the cargo net hook
Do not hang items other than the cargo net.
372
3-5. Other interior features
Garage door opener
The garage door opener can be trained to operate garage doors, gates, entry doors, door locks, home lighting systems, security systems, and other devices.
The garage door opener (HomeLink
®
Universal Transceiver) is manufactured under license from HomeLink
®
.
Training the HomeLink
®
(for U.S. owners)
The HomeLink
®
compatible transceiver in your vehicle has 3 buttons which can be trained to operate 3 different devices. Refer to the training method below appropriate for the device.
Indicator light
Buttons
3
: If equipped
373
3-5. Other interior features
■
Training the HomeLink
®
Point the remote control transmitter for the device 1 to 3 in. (25 to 75 mm) from the HomeLink
® control buttons.
Keep the indicator on the
HomeLink
®
in view while training.
Press and hold down one of the buttons on the HomeLink
®
and the button on the transmitter.
When the indicator on the
HomeLink
®
changes from a slow to a rapid flash, you can release both buttons.
If the HomeLink
®
indicator comes on but does not flash, or flashes rapidly for 2 seconds and remains lit, the HomeLink
® button is already trained. Use the other buttons or follow the “Retraining a
HomeLink
® button” instructions.
(
P. 378)
374
3-5. Other interior features
Test the operation of the
HomeLink
®
by pressing the newly trained button.
If training a garage door opener, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the
Rolling Code type. Press and hold the trained HomeLink
® button. The garage door has the rolling code feature if the indicator
(on the HomeLink
®
) flashes rapidly for 2 seconds and then remains lit. If your transmitter is the Rolling Code type, proceed to the heading “Training a rolling code system”.
Repeat the steps above to train another device for each of the remaining HomeLink
®
buttons.
3
375
3-5. Other interior features
■
Training a Rolling Code system (for U.S. owners)
If your device is Rolling Code equipped, follow the steps under the heading “Training the HomeLink
®
” before proceeding with the steps listed below.
Locate the learn button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener.
Refer to the operation manual supplied with the garage door opener for the location of the learning button.
Press the learning button.
Following this step, you have 30 seconds in which to initiate step 3 below.
Press and hold the vehicle’s trained HomeLink
®
button for 2 seconds and release it. Repeat this step once again. The garage door may open.
If the garage door opens, the training process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the training process by opening the garage door.
The ceiling mounted garage door opener motor should now recognize the HomeLink
®
transceiver and operate the garage door.
Repeat the steps above to train another rolling code system for any of the remaining HomeLink
®
buttons.
376
3-5. Other interior features
■
Training an entry gate (for U.S. owners)/Training a device in the Canadian market
Place the remote control transmitter 1 to 3 in. (25 to 75 mm) away from the HomeLink
®
buttons
Keep the HomeLink
®
indicator light in view while training.
Press and hold the selected HomeLink
®
button.
Repeatedly press and release (cycle) one of the buttons on the remote control transmitter for 2 seconds at a time until
is completed.
When the HomeLink
®
indicator light starts to flash rapidly, release the buttons on the HomeLink
®
.
Test the HomeLink
®
operation by pressing the newly trained button. Check to see if the gate/device operates correctly.
Repeat the steps above to train another device for any of the remaining HomeLink
®
buttons.
■ Training other devices
To train other devices such as home security systems, home door locks and lighting, contact your Toyota dealer for assistance.
■ Retraining a button
The individual HomeLink
®
buttons cannot be erased but can be retrained. To retrain a button, follow the “Retraining a HomeLink
® button” instructions.
3
377
3-5. Other interior features
Operating HomeLink
®
Press the appropriate HomeLink
®
button. The HomeLink
®
indicator light should come on.
The HomeLink
®
compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed.
Retraining a HomeLink
®
button
Press and hold the desired HomeLink
® button. After 20 seconds, the
HomeLink
®
indicator light will start flashing slowly. Keep pressing the
HomeLink
®
button and then follow the “Training the HomeLink
®
(for
U.S. owners)” instructions. (
P. 373)
Erasing the entire HomeLink
®
memory (all three programs)
Press and hold down the 2 outside buttons for 10 seconds until the indicator flashes.
If you sell your vehicle, be sure to erase the programs stored in the
HomeLink
®
memory.
378
3-5. Other interior features
■ Before training
● Install a new battery in the remote control transmitter.
● The battery side of the remote control transmitter must be pointed away from the HomeLink
®
button.
■ Certification for the garage door opener
For vehicles sold in the U.S.A.
FCC ID: NZLWZLHL4
NOTE:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For vehicles sold in Canada
NOTE:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
■ When support is necessary
Visit on the web at www.homelink.com or call 1-800-355-3515.
3
379
3-5. Other interior features
CAUTION
■ When training a garage door or other remote control devices
The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm.
■ Conforming to federal safety standards
Do not use the HomeLink
®
compatible transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards.
This includes any garage door that cannot detect an interfering object. A door or device without these features increases the risk of death or serious injury.
380
3-5. Other interior features
Compass (vehicles with auto anti-glare inside rear view mirror)
The compass on the inside rear view mirror indicates the direction in which the vehicle is heading.
■
Operation
Type A
To turn the compass on or off, press the button.
3
Type B
381
3-5. Other interior features
■
Displays and directions
Display
N
NE
E
SE
S
SW
W
NW
Direction
North
Northeast
East
Southeast
South
Southwest
West
Northwest
382
Calibrating the compass
3-5. Other interior features
Samoa: 5 Guam: 8 Saipan: 8
The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle.
If you cross over one of the map boundaries shown in the illustration, the compass will deviate.
To obtain higher precision or perfect calibration, refer to “Deviation calibration”.
■ Deviation calibration
Stop the vehicle where it is safe to drive in a circle.
Press the button until a number (1 to 15) appears on the compass display.
Type A
3
383
3-5. Other interior features
Type B
Press the button, and referring to the map above, select the number of the zone where you are.
If the direction is displayed several seconds after adjustment, the calibration is complete.
■
Circling calibration
When “C” appears on the display, drive the vehicle at 5 mph
(8 km/h) or less in a circle until a direction is displayed.
If there is not enough space to drive in a circle, drive around the block until the direction is displayed.
384
3-5. Other interior features
■ Conditions unfavorable to correct operation
The compass may not show the correct direction in the following conditions:
● The vehicle is stopped immediately after turning.
● The vehicle is on an inclined surface.
● The vehicle is in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).
● The vehicle has become magnetized.
(There is a magnet or metal object near the inside rear view mirror.)
● The battery has been disconnected.
● A door is open.
3
CAUTION
■ While driving the vehicle
Do not adjust the display. Adjust the display only when the vehicle is stopped.
■ When doing the circling calibration
Secure a wide space, and watch out for people and vehicles in the vicinity.
Do not violate any local traffic rules while performing circling calibration.
NOTICE
■ To avoid the compass malfunctions
Do not place magnets or any metal objects near the inside rear view mirror.
Doing this may cause the compass sensor to malfunction.
■ When doing the circling calibration
● Do not perform a circling calibration of the compass in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields.
● During calibration, do not operate electric systems (power windows, etc.) as they may interfere with the calibration.
385
3-5. Other interior features
386
Maintenance and care
4
Cleaning and protecting the vehicle exterior......... 388
Cleaning and protecting the vehicle interior.......... 391
Maintenance requirements .................. 394
General maintenance....... 396
Emission inspection and maintenance (I/M) programs .......................... 399
4-3. Do-it-yourself maintenance
Do-it-yourself service precautions .................... 400
Hood ................................ 404
Engine compartment........ 406
Tires ................................. 422
Tire inflation pressure ...... 431
Wheels ............................. 436
Air conditioning filter......... 439
Wireless remote control battery ............................ 442
Checking and replacing fuses .............................. 444
Light bulbs........................ 454
387
4-1. Maintenance and care
Cleaning and protecting the vehicle exterior
Perform the following to protect the vehicle and maintain it in prime condition.
● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Wash the vehicle body using a sponge or soft cloth, such as a chamois.
● For hard-to-remove marks, use car wash soap and rinse thoroughly with water.
● Wipe away any water.
● Wax the vehicle when the waterproof coating deteriorates.
If water does not bead on a clean surface, apply wax when the vehicle body is cool.
■ Automatic car washes
● Fold the mirrors and remove the detachable pole antenna before washing the vehicle. Start washing from the front of the vehicle. Make sure to re-install the detachable pole antenna and extend the mirrors before driving.
● Brushes used in automatic car washes may scratch the vehicle surface and harm your vehicle’s paint.
● In certain automatic car washes, the roof antenna (if equipped) may interfere with machine operation. This may prevent the vehicle from being cleaned properly or result in damage to the roof antenna.
■ High pressure car washes
Do not allow the nozzles of the car wash to come within close proximity of the windows. Before entering an automatic car wash, check that the fuel filler door on your vehicle is closed properly.
388
4-1. Maintenance and care
■ Aluminum or chrome cladded wheels (if equipped)
● Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.
● Do not use detergent on the wheels when they are hot, for example after driving for long distance in the hot weather.
● Wash detergent from the wheels immediately after use.
■ Bumpers and side moldings
Do not scrub with abrasive cleaners.
CAUTION
■ Caution about the exhaust pipe
Exhaust gasses cause the exhaust pipe to become quite hot.
When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.
4
NOTICE
■ To prevent paint deterioration and corrosion on the body and components (aluminum or chrome cladded wheels etc.)
● Wash the vehicle immediately in the following cases:
• After driving near the sea coast
• After driving on salted roads
• If you see coal tar or tree sap on the paint surface
• If you see dead insects, insect droppings or bird droppings on the paint
• After driving in an area contaminated with soot, oily smoke, mine dust, iron powder or chemical substances
• If the vehicle becomes heavily soiled in dust or mud
• If liquids such as benzene and gasoline are spilled on the paint surface
● If the paint is chipped or scratched, have it repaired immediately.
● To prevent the wheels from corroding, remove any dirt and store in a place with low humidity when storing the wheels.
389
4-1. Maintenance and care
NOTICE
● Clean the drainage hole of the deck regularly.
If the drainage hole is stopped up, the water will not be able to flow, and it will cause rust.
■ Cleaning the exterior lights
● Wash carefully. Do not use organic substances or scrub with a hard brush.
This may damage the surfaces of the lights.
● Do not apply wax on the surfaces of the lights.
Wax may cause damage to the lenses.
■ Detachable pole antenna installation and removal precautions
● Before driving, ensure that the antenna is installed.
● When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position.
390
4-1. Maintenance and care
Cleaning and protecting the vehicle interior
The following procedures will help protect your vehicle’s interior and keep it in top condition:
■
Protecting the vehicle interior
Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
■
Cleaning the leather areas
● Remove dirt and dust using a vacuum cleaner.
● Wipe any excess dirt and dust with a soft cloth dampened with diluted detergent.
Use a diluted water solution of approximately 5% neutral wool detergent.
● Wring out any excess water from the cloth and thoroughly wipe off all remaining traces of detergent.
● Wipe the surface with a dry, soft cloth to remove any remaining moisture. Allow the leather to dry in a shaded and ventilated area.
■
Synthetic leather areas
● Remove loose dirt using a vacuum cleaner.
● Apply a mild soap solution to the synthetic leather using a sponge or soft cloth.
● Allow the solution to soak in for a few minutes. Remove the dirt and wipe off the solution with a clean, damp cloth.
4
■ Caring for leather areas
Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.
391
4-1. Maintenance and care
■ Shampooing the carpets
There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained when keeping the carpet as dry as possible.
■ Seat belts
Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.
CAUTION
■ Water in the vehicle
● Do not splash or spill liquid in the vehicle.
Doing so may cause the electrical components etc. to malfunction or catch fire.
● Do not get any of the SRS components or wiring in the vehicle interior wet.
(
Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or severe injury.
■ Cleaning the interior (especially instrument panel)
Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver’s view and leading to an accident, resulting in death or serious injury.
392
4-1. Maintenance and care
NOTICE
■ Cleaning detergents
● Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces.
● Do not use polish wax or polish cleaner. The instrument panel’s or other interior part’s painted surface may be damaged.
■ Preventing damage to leather surfaces
Observe the following precautions to avoid damage to and deterioration of leather surfaces.
● Remove any dust or dirt on leather surfaces immediately.
● Do not expose the vehicle to direct sunlight for extended periods of time.
Park the vehicle in the shade, especially during summer.
● Do not place items made of vinyl, plastic, or that contain wax on the upholstery, as they may stick to the leather surface if the vehicle interior heats up significantly.
■ Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.
4
393
4-2. Maintenance
Maintenance requirements
To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance.
■
General maintenance
Should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.
■
Scheduled maintenance
Should be performed at specified intervals according to the maintenance schedule.
For details about maintenance items and schedules, refer to the
“Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
■
Do-it-yourself maintenance
You can perform some maintenance procedures yourself.
Please be aware that do-it-yourself maintenance may affect warranty coverage.
The use of Toyota Repair Manuals is recommended.
For details about warranty coverage, see the separate “Owner’s
Warranty Information Booklet”, “Owner’s Manual Supplement”.
■ Repair and replacement
It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the warranty coverage.
394
4-2. Maintenance
■ Resetting the maintenance required reminder light (U.S.A. only)
After the required maintenance is performed according to the maintenance schedule, please reset the reminder light.
To reset the data, follow the procedures described below:
Switch the display to the trip meter A when the engine is running.
(
Turn the engine switch to the LOCK position.
While pressing the ODO/TRIP button (
switch to the ON position. Continue to press and hold the button until the odometer displays 000000.
If the system fails to reset, the light will continue flashing.
■ Allow inspection and repairs to be performed by a Toyota dealer
● Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
● Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.
4
CAUTION
■ Warning in handling of battery
● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.
● Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.
● Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (
395
4-2. Maintenance
General maintenance
Listed below are the general maintenance items that should be performed at the intervals specified in the “Scheduled Maintenance
Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your
Toyota dealer or qualified service shop for advice.
Engine compartment
Items
Battery
Brake fluid
Engine coolant
Engine oil
Exhaust system
Power steering fluid
Radiator/condenser/hoses
Washer fluid
Check points
Maintenance-free.
(
At the correct level? (
At the correct level?
(
At the correct level?
(
No fumes or strange sounds?
At the correct level?
(
Not blocked with foreign matter?
(
At the correct level?
(
396
4-2. Maintenance
Vehicle interior
Items
Accelerator pedal
Automatic transmission “Park” mechanism
Brake pedal
Brakes
Clutch pedal
Head restraints
Indicators/buzzers
Lights
Parking brake
Seat belts
Seats
Check points
• Moves smoothly (without uneven pedal effort or catching)?
• Can the vehicle be held securely on an incline with the shift lever in
P?
• Moves smoothly?
• Does it have appropriate clearance and correct amount of free play?
• Not pull to one side when applied?
• Loss of brake effectiveness?
• Spongy feeling brake pedal?
• Pedal almost touches floor?
• Moves smoothly?
• Does it have correct amount of free play?
• Move smoothly and lock securely?
• Function properly?
• Do all the lights come on?
• Headlights aimed correctly?
• Moves smoothly?
• Can hold the vehicle securely on an incline?
• Does the seat belt system operate smoothly?
• Are the belts undamaged?
• Do the seat controls operate properly?
4
397
4-2. Maintenance
Steering wheel
Items Check points
• Moves smoothly?
• Has correct free play?
• No strange noises?
Vehicle exterior
Doors
Engine hood
Fluid leaks
Items
Tire
Windshield wipers
Check points
• Operate smoothly?
• The lock system works properly?
• Is there any leakage after parking?
• Inflation pressure is correct?
• Tire surfaces not worn or damaged?
• Tires rotated according to the maintenance schedule?
• Wheel nuts are not loose?
• The wiper blades should not show any signs of cracking, splitting, wear, contamination or deformation.
• The wiper blades should clear the windshield without streaking or skipping.
CAUTION
■ If the engine is running
Turn the engine off and ensure that there is adequate ventilation before performing maintenance checks.
398
4-2. Maintenance
Emission inspection and maintenance (I/M) programs
Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system monitors the operation of the emission control system.
■
If the malfunction indicator lamp comes on
The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/
M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.
■
Your vehicle may not pass the I/M test:
● When the battery is disconnected or discharged
Readiness codes that are set during ordinary driving are erased.
Also, depending on your driving habits, the readiness codes may not be completely set.
● When the fuel tank cap is loose
The malfunction indicator lamp comes on as a temporary malfunction and your vehicle may not pass the I/M test.
■
When the malfunction indicator lamp goes off after several driving trips
The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.
■
If your vehicle does not pass the I/M test
Contact your Toyota dealer to prepare the vehicle for re-testing.
4
399
4-3. Do-it-yourself maintenance
Do-it-yourself service precautions
If you perform maintenance yourself, be sure to follow the correct procedures as given in these sections.
Fuses
Items
Battery condition
Brake fluid level
Engine oil level
(
(
Engine coolant level (
P. 412)
P. 408)
(
Parts and tools
• Warm water
• Baking soda
• Grease
• Conventional wrench
(for terminal clamp bolts)
• FMVSS No.116 DOT 3 or SAE
J1703 brake fluid
• Rag or paper towel
• “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, nonamine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
U.S.A.:
“Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water.
Canada:
“Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water.
• Toyota Genuine Motor Oil or equivalent
• Rag or paper towel
• Funnel (used only for adding oil)
• Fuse with same amperage rating as original
400
4-3. Do-it-yourself maintenance
Light bulbs
Items
(
Power steering fluid level
(
Parts and tools
• Bulb with same number and wattage rating as original
• Phillips-head screwdriver
• Conventional wrench
• Automatic transmission fluid
DEXRON
®
II or III
• Rag or paper towel
Radiator and condenser
(
Tire inflation pressure (
Washer fluid
(
• Tire pressure gauge
• Compressed air source
• Washer fluid containing antifreeze
(for winter use)
• Water
4
401
4-3. Do-it-yourself maintenance
CAUTION
The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions.
■ When working on the engine compartment
● Keep hands, clothing, and tools away from the moving fan and engine drive belt.
● Be careful not to touch the engine, radiator, exhaust manifold, etc. right after driving as they may be hot. Oil and other fluids may also be hot.
● Do not leave anything that may burn easily, such as paper or rags, in the engine compartment.
● Do not smoke, cause sparks or expose an open flame to fuel or the battery. Fuel and battery fumes are flammable.
● Be extremely cautious when working on the battery. It contains poisonous and corrosive sulfuric acid.
● Take care because brake fluid can harm your hands or eyes and damage painted surfaces.
If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately.
If you still experience discomfort, see a doctor.
■ When working near the cooling fan or radiator grille
Be sure the engine switch is off.
With the engine switch on, the cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high.
■ Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in the eyes.
402
4-3. Do-it-yourself maintenance
NOTICE
■ If you remove the air cleaner
Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air.
■ If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, it may indicate a serious problem.
4
403
4-3. Do-it-yourself maintenance
Hood
Release the lock from the inside of the vehicle to open the hood.
Pull the hood release lever.
The hood will pop up slightly.
Pull up the hood catch lever and lift the hood.
404
4-3. Do-it-yourself maintenance
Hold the hood open by inserting the supporting rod into the slot.
CAUTION
■ Pre-driving check
Check that the hood is fully closed and locked.
If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.
■ After installing the support rod into the slot
Make sure the rod supports the hood securely from falling down on to your head or body.
4
NOTICE
■ When closing the hood
Be sure to return the support rod to its clip before closing the hood. Closing the hood with the support rod up could cause the hood to bend.
405
4-3. Do-it-yourself maintenance
Engine compartment
2.7 L 4-cylinder (2TR-FE) engine
406
Washer fluid tank (
Radiator cap
Engine coolant reservoir
(
P. 412)
Engine oil filler cap
(
Power steering fluid reservoir
(
Engine oil level dipstick
(
P. 408)
Brake fluid reservoir
(
Fuse box
Battery
(
(
Condenser
Radiator
(
(
4.0 L V6 (1GR-FE) engine
4-3. Do-it-yourself maintenance
Washer fluid tank (
Power steering fluid reservoir
(
Radiator cap
Engine oil level dipstick
(
P. 408)
Engine coolant reservoir
(
P. 412)
Engine oil filler cap
(
Brake fluid reservoir
(
Fuse box
Battery
(
(
Condenser
Radiator
(
(
4
407
4-3. Do-it-yourself maintenance
Engine oil
Engine oil
With the engine at operating temperature and turned off, check the oil level on the dipstick.
■ Checking the engine oil
Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Hold a rag under the end and pull the dipstick out.
2.7 L 4-cylinder (2TR-FE) engine
4.0 L V6 (1GR-FE) engine
408
Wipe the dipstick clean.
Reinsert the dipstick fully.
4-3. Do-it-yourself maintenance
Holding a rag under the end, pull the dipstick out and check the oil level.
Low
Normal
Excessive
The shape of the dipstick may differ depending on the type of vehicle or engine.
Wipe the dipstick and reinsert it fully.
■
Adding engine oil
2.7 L 4-cylinder (2TR-FE) engine
If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.
4
409
4-3. Do-it-yourself maintenance
4.0 L V6 (1GR-FE) engine
Make sure to check the oil type and prepare the items needed before adding oil.
Engine oil selection
Items Clean funnel
Remove the oil filler cap, turning it counterclockwise.
Add engine oil slowly.
Checking the dipstick.
Reinstall the filler cap, turning it clockwise.
The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows:
2.7 L 4-cylinder (2TR-FE) engine
1.4 qt. (1.3 L, 1.1 lmp.qt.)
4.0 L V6 (1GR-FE) engine
1.6 qt. (1.5 L, 1.3 lmp.qt.)
410
4-3. Do-it-yourself maintenance
■ Engine oil consumption
A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
● When the engine is new, for example directly after purchasing the vehicle or after replacing the engine
● If low quality oil or oil of an inappropriate viscosity is used
● When driving at high engine speeds or with a heavy load, when towing, or when driving while accelerating or decelerating frequently
● When leaving the engine idling for a long time, or when driving frequently through heavy traffic
CAUTION
■ Used engine oil
● Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.
● Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
● Do not leave used engine oil within the reach of children.
4
411
4-3. Do-it-yourself maintenance
NOTICE
■ To prevent serious engine damage
Check the oil level on regular basis.
■ When replacing the engine oil
● Be careful not to spill engine oil on the vehicle components.
● Avoid overfilling, as the engine could be damaged.
● Check the oil level on the dipstick every time you refill the vehicle.
● Be sure the engine oil filler cap is properly tightened.
Engine coolant
The coolant level is satisfactory if it is between the FULL and LOW lines on the reservoir when the engine is cold.
Reservoir cap
FULL line
LOW line
If the level is on or below the
LOW line, add coolant up to the
FULL line.
412
4-3. Do-it-yourself maintenance
■ If the coolant level drops within a short time after replenishing
Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump.
If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system.
■ Coolant selection
Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
U.S.A.: “Toyota Super Long Life Coolant” is a mixture of 50% coolant and
50% deionized water. (Enabled: -31
F [-35C])
Canada: “Toyota Super Long Life Coolant” is a mixture of 55% coolant and
45% deionized water. (Enabled: -44
F [-42C])
For more details about engine coolant, contact your Toyota dealer.
CAUTION
■ When the engine is hot
Do not remove the radiator cap.
The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing serious injuries, such as burns.
4
NOTICE
■ When adding engine coolant
Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.
■ If you spill coolant
Be sure to wash it off with water to prevent damage to parts or paint.
413
4-3. Do-it-yourself maintenance
Radiator and condenser
Check the radiator and condenser and clear any foreign objects.
If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer.
CAUTION
■
When the engine is hot
Do not touch the radiator or condenser as they may be hot and cause serious injuries, such as burns.
Brake fluid
■
Checking fluid level
Type A
The brake fluid level should be between the MAX and MIN lines on the reservoir.
MAX line
MIN line
Type B
MAX line
MIN line
414
4-3. Do-it-yourself maintenance
■
Adding fluid
Make sure to check the fluid type and prepare the necessary items.
Fluid type
Items
FMVSS No.116 DOT 3 or SAE J1703 brake fluid
Rag or paper towel
Type B only
Turn the engine off.
Depress the brake pedal 20 times or more.
Remove the reservoir cap.
Add newly opened brake fluid up to the MAX line.
■ Brake fluid can absorb moisture from the air
Excess moisture in the fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid.
CAUTION
■ When filling the reservoir
Take care because brake fluid can harm your hands or eyes and damage painted surfaces.
If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately.
If you still experience discomfort, see a doctor.
4
NOTICE
■ If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, it may indicate a serious problem.
■ If you spill fluid
Be sure to wash it off with water to prevent damage to parts or paint.
415
4-3. Do-it-yourself maintenance
Power steering fluid
■ Fluid level
The fluid level should be within the appropriate range.
2.7 L 4-cylinder (2TR-FE) engine
Full (when cold)
Add fluid (when cold)
Full (when hot)
Add fluid (when hot)
Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 104°F - 175°F [40°C - 80°C])
Cold: Engine has not been run for about 5 hours. (Room temperature, 32°F - 104°F [0°C - 40°C])
4.0 L V6 (1GR-FE) engine
Full (when cold)
Add fluid (when cold)
Full (when hot)
Add fluid (when hot)
416
Hot: Vehicle has been driven around 50 mph (80 km/h) for 20 minutes, or slightly longer in frigid temperatures. (Fluid temperature, 140°F - 175°F [60°C - 80°C])
Cold: Engine has not been run for about 5 hours. (Room temperature, 50°F - 85°F [10°C - 30°C])
4-3. Do-it-yourself maintenance
■
Checking the fluid level
Make sure to check the fluid type and prepare the necessary items.
Fluid type
Items
Automatic transmission fluid DEXRON
®
II or III
Rag or paper towel
Clean all dirt off the reservoir.
Remove the cap by turning it counterclockwise.
Wipe the dipstick clean.
Reinstall and remove the reservoir cap again.
Check the fluid level.
CAUTION
■ Checking the fluid level
Take care, as the reservoir may be hot.
4
NOTICE
■ When adding fluid
Avoid overfilling, or the power steering may be damaged.
■ After replacing the reservoir cap
Check the steering box case, vane pump and hose connections for leaks or damage.
417
4-3. Do-it-yourself maintenance
Battery
■ Battery exterior
Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.
Terminals
Hold-down clamp
■
Before recharging
When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging:
●
If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
●
Make sure the power switch on the charger is off when connecting and disconnecting the charger cables to the battery.
418
4-3. Do-it-yourself maintenance
CAUTION
■ Chemicals in the battery
A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near battery:
● Do not cause sparks by touching the battery terminals with tools.
● Do not smoke or light a match near the battery.
● Avoid contact with eyes, skin and clothes.
● Never inhale or swallow electrolyte.
● Wear protective safety glasses when working near the battery.
● Keep children away from the battery.
■ Where to safety charge the battery
Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.
■ How to recharge the battery
Only perform a slow charge (5A or less).
The battery may explode if charged at a quicker rate.
■ Emergency measures regarding electrolyte
● If electrolyte gets in your eyes
Flush your eyes with clean water for at least 15 minutes and get immediate medical attention. If possible, continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
● If electrolyte gets on your skin
Wash the affected area thoroughly. If you feel pain or burning, get medical attention immediately.
● If electrolyte gets on your clothes
It can soak through clothing on to your skin. Immediately take off the clothing and follow the procedure above if necessary.
● If you accidentally swallow electrolyte
Drink a large quantity of water or milk. Get emergency medical attention immediately.
4
419
4-3. Do-it-yourself maintenance
NOTICE
■ When recharging the battery
Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
Washer fluid
If the washer does not work, the washer tank may be empty.
Open the lid.
Add washer fluid.
CAUTION
■ When refilling the washer fluid
Do not refill the washer fluid when the engine is hot or running, as the washer fluid contains alcohol and may catch fire if spilled on the engine etc.
420
4-3. Do-it-yourself maintenance
NOTICE
■ Do not use any fluid other than washer fluid
Do not use soapy water or engine antifreeze instead of washer fluid.
Doing so may cause streaking on the vehicle’s painted surfaces.
■ Diluting washer fluid
Dilute washer fluid with water as necessary.
Refer to the freezing temperatures listed on the label of the washer fluid bottle.
4
421
4-3. Do-it-yourself maintenance
Tires
Replace or rotate tires in accordance with maintenance schedules and treadwear.
■
Checking tires
New tread
Treadwear indicator
Worn tread
The location of treadwear indicators is shown by the
“TWI” or “ ” marks, etc., molded on the sidewall of each tire.
Check spare tire condition and inflation pressure if not rotated.
■ Tire rotation
Rotate the tires in the order shown.
Front
To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the same interval as tire inspection.
Vehicles with P215/70R15 and P265/70R16 tires: Do not fail to initialize the tire pressure warning system after tire rotation.
■
The tire pressure warning system
Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (
422
4-3. Do-it-yourself maintenance
Installing tire pressure warning valves and transmitters
When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed.
When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (
Initializing the tire pressure warning system
■
The tire pressure warning system must be initialized in the following circumstances:
● Vehicles with P215/70R15 and P265/70R16 tires: When rotating the tires on vehicles differing with front and rear tire inflation pressures.
● When changing the tire inflation pressure by changing traveling speed or load weight, etc.
● When changing the tire size.
When the tire pressure warning system is initialized, the current tire inflation pressure is set as the pressure benchmark.
■
How to initialize the tire pressure warning system
Park the vehicle in safe place and turn the engine switch to the LOCK position.
While the vehicle is moving, initialization is not performed.
Adjust the tire inflation pressure to the specified cold tire inflation pressure level. (
Ma ke sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level.
Turn the engine switch to the ON position.
4
423
4-3. Do-it-yourself maintenance
Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.
Wait for a few minutes with the engine switch in the ON position, and then turn the engine switch to the ACC or LOCK position.
Registering ID codes
The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your
Toyota dealer.
424
4-3. Do-it-yourself maintenance
■ When to replace your vehicle’s tires
Tires should be replaced if:
● You have tire damage such as cuts, splits, cracks deep enough to expose the fabric or bulges indicating internal damage
● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage
If you are not sure, consult with your Toyota dealer.
■ Replacing tires and wheels
If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1 minute and stays on to indicate a system malfunction.
■ Tire life
Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.
■ If the tread wears down below 0.16 in. (4 mm) on snow tires
The effectiveness of snow tires is lost.
■ Maximum load of tire
Check that the number given by dividing the maximum load by 1.10 of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings
(GAWR) of either the front axle or the rear axle, whichever is greater.
For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire (
Access Cab models
4
425
4-3. Do-it-yourself maintenance
Double Cab models
■ Tire types
1 Summer tires
Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.
2 All season tires
All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions, as well as for use year round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.
3 Snow tires
For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restriction. Snow tires should be installed on all wheels. (
■ Initializing the tire pressure warning system
Initialize the tire pressure warning system with the tire inflation pressure adjusted to the specified level.
426
4-3. Do-it-yourself maintenance
■ If you push the tire pressure warning reset switch accidentally
If initialization is performed, adjust the tire inflation pressure to the specified level and initialize the tire pressure warning system again.
■ When the initialization of the tire pressure warning system has failed
Initialization can be completed in a few minutes. However, in the following cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer.
● When operating the tire pressure warning reset switch, the tire pressure warning light does not blink 3 times.
● After carrying out the initialization procedure, the tire pressure warning light blinks for 1 minute then stays on after driving for about 20 minutes.
■ Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.
4
427
4-3. Do-it-yourself maintenance
■ Tire pressure warning system certification
FCC ID: PAXPMV107J
FCC ID: PAXPMV108J
FCC ID: HYQ13BCX
For vehicles sold in U.S.A.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
For vehicles sold in Canada
NOTE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
428
4-3. Do-it-yourself maintenance
CAUTION
■ When inspecting or replacing tires
Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous handling characteristics, which may lead to an accident resulting in death or serious injury.
● Do not mix tires of different makes, models or tread patterns.
Also, do not mix tires of remarkably different treadwear.
● Do not use tire sizes other than those recommended by Toyota.
● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
● Do not mix summer, all season and winter tires.
● Do not use tires that have been used on another vehicle.
● Do not use tires if you do not know how they were used previously.
■ When initializing the tire pressure warning system
Do not push the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pressure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.
4
429
4-3. Do-it-yourself maintenance
NOTICE
■ Repairing or replacing tires, wheels, tire pressure warning valves, transmitters and tire valve caps
● When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly.
● When replacing tire valve caps, do not use tire valve caps other than those specified. The cap may become stuck.
■ To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (
■ Driving on rough roads
Take particular care when driving on roads with loose surfaces or potholes.
These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition driving on rough roads may cause damage to the tires themselves, as well as the vehicle’s wheels and body.
■ If tire inflation pressures become low while driving
Do not continue driving, or your tires and/or wheels may be ruined.
430
4-3. Do-it-yourself maintenance
Tire inflation pressure
■
Tire inflation pressure
The recommended cold tire inflation pressure and tire size is displayed on the tire and loading information label. (
Access Cab models
4
431
4-3. Do-it-yourself maintenance
Double Cab models
432
4-3. Do-it-yourself maintenance
■
Inspection and adjustment procedure
Tire valve
Tire pressure gauge
Remove the tire valve cap.
Press the tip of the tire pressure gauge onto the tire valve.
Read the pressure using the graduations of the gauge.
If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.
If you add too much air, press the center of the valve to lower.
After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage.
Reinstall the tire valve cap.
4
433
4-3. Do-it-yourself maintenance
■ Tire inflation pressure check interval
You should check tire pressure every two weeks, or at least once a month.
Do not forget to check the spare.
■ Effects of incorrect tire inflation pressure
Driving with incorrect tire inflation pressure may result in the following:
● Reduced fuel efficiency
● Reduced driving comfort and tire life
● Reduced safety
● Damage to the drive train
If a tire needs frequent refilling, have it checked by your Toyota dealer.
■ Instructions for checking tire inflation pressure
When checking tire inflation pressure, observe the following:
● Check only when the tires are cold.
If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
● Always use a tire pressure gauge.
The appearance of the tire can be misleading. In addition, tire inflation pressures that are even just a few pounds off can degrade ride and handling.
● Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving.
● Never exceed the vehicle capacity weight.
Passengers and luggage weight should be placed so that the vehicle is balanced.
434
4-3. Do-it-yourself maintenance
CAUTION
■ Proper inflation is critical to save tire performance
Keep your tires properly inflated.
Otherwise, the following conditions may occur and result in an accident causing death or serious injury.
● Excessive wear
● Uneven wear
● Poor handling
● Possibility of blowouts resulting from overheated tires
● Poor sealing of the tire bead
● Wheel deformation and/or tire separation
● A greater possibility of tire damage from road hazards
NOTICE
■ When inspecting and adjusting tire inflation pressure
Be sure to reinstall the tire valve caps.
Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.
4
435
4-3. Do-it-yourself maintenance
Wheels
If a wheel is bent, cracked or heavily corroded, it should be replaced.
Otherwise, the tire may separate from the wheel or cause loss of handling control.
■
Wheel selection
When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset * .
Replacement wheels are available at your Toyota dealer.
*
: Conventionally referred to as “offset”.
Toyota does not recommend using:
● Wheels of different sizes or types
● Used wheels
● Bent wheels that have been straightened
■
Wheel precautions
● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels.
● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).
● Be careful not to damage the aluminum wheels when using tire chains.
● Use only Toyota genuine balance weights or equivalent and a plastic or rubber hammer when balancing your wheels.
436
4-3. Do-it-yourself maintenance
■ When replacing wheels
The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (
CAUTION
■ When replacing wheels
● Do not use wheels that are a different size from those recommended in the Owner’s Manual, as this may result in loss of handling control.
● Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or serious injury.
■ When installing the wheel nuts
Tapered portion
● Be sure to install the wheel nuts with the tapered end facing inward. Installing the nuts with the tapered end facing outward can cause wheel to break and eventually cause a wheel to come off while driving, which could lead to an accident resulting in death or serious injury.
● Never use oil or grease on the wheel bolts or wheel nuts.
Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.
4
437
4-3. Do-it-yourself maintenance
NOTICE
■ Replacing tire pressure warning valves and transmitters
● Because tire repair or replacement may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by your
Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your
Toyota dealer.
● Ensure that only genuine Toyota wheels are used on your vehicle.
Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.
438
4-3. Do-it-yourself maintenance
Air conditioning filter
The air conditioning filter must be changed regularly to maintain air conditioning efficiency.
■
Removal method
Turn the engine switch to the LOCK position.
Open the glove box.
Slide off the damper.
4
Push in each side of the glove box to disconnect the claws.
439
4-3. Do-it-yourself maintenance
Open the filter door.
Remove the filter.
■
Replacement method
Remove the air conditioning filter and replace it with a new one.
When installing the filter, follow the instructions indicated on the label.
440
4-3. Do-it-yourself maintenance
■ Checking interval
Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)
■ If air flow from the vents decreases dramatically
The filter may be clogged. Check the filter and replace if necessary.
NOTICE
■
When using the air conditioning system
Make sure that a filter is always installed.
Using the air conditioning system without a filter may cause damage to the system.
4
441
4-3. Do-it-yourself maintenance
Wireless remote control battery
Replace the battery with a new one if it is discharged.
■
You will need the following items:
Lithium battery CR2032
■
Replacing the battery
Remove the cover using a coin protected with tape etc.
Remove the discharged transmitter battery.
Insert a new battery with the
“+” terminal facing up.
: If equipped
442
4-3. Do-it-yourself maintenance
■ If the wireless remote control battery is discharged
The following symptoms may occur.
● The wireless remote control will not function properly.
● The operational range is reduced.
■ Use a CR2032 lithium battery
● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores.
● Replace only with the same or equivalent type recommended by your
Toyota dealer.
● Dispose of used batteries according to the local laws.
CAUTION
■ Removed battery and other parts
These parts are small and if swallowed by a child, they can cause choking.
Keep away from children. Failure to do so could result in death or serious injury.
■ Certification for the lithium battery
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUC-
TIONS
4
NOTICE
■ For normal operation after replacing the battery
Observe the following precautions to prevent accidents.
● Always work with dry hands.
Moisture may cause the battery to rust.
● Do not touch or move any other components inside the remote control.
● Do not bend either of the battery terminals.
443
4-3. Do-it-yourself maintenance
Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.
Turn the engine switch to the LOCK position.
The fuses are located in the following places. To check the fuses, follow the instructions below.
Engine compartment
Push the tab in and lift the lid off.
Under the instrument panel
1.Open the auxiliary box.
2.Pull up the box and disengage the claws. Remove the stoppers from the cutouts and remove the box.
444
4-3. Do-it-yourself maintenance
After a system failure, see “Fuse layout and amperage ratings” (
P. 447) for details about which fuse to check.
Remove the fuse with the pullout tool.
Check if the fuse has blown.
Type A
Normal fuse
Blown fuse
Replace it with one of an appropriate amperage rating.
The amperage rating can be found on the fuse box lid.
4
445
4-3. Do-it-yourself maintenance
Type B
Type C
Type D
Normal fuse
Blown fuse
Replace it with one of an appropriate amperage rating.
The amperage rating can be found on the fuse box lid.
Normal fuse
Blown fuse
Replace it with one of an appropriate amperage rating.
The amperage rating can be found on the fuse box lid.
Normal fuse
Blown fuse
Replace it with one of an appropriate amperage rating.
The amperage rating can be found on the fuse box lid.
446
Fuse layout and amperage ratings
■ Engine compartment
Type A
4-3. Do-it-yourself maintenance
Type B
4
447
4-3. Do-it-yourself maintenance
448
1 A/C
2
3
4
Fuse
TOWING TAIL
FOG FR
5 TOWING BRK
6 EFI
7 S/HTR NO.2
8 OBD
9 BATT CHG
10 AIR PMP HTR
11 TOWING
12 TURN & HAZ
13 RADIO NO.2
14 H-LP RH-LO
15 H-LP LH-LO
16 H-LP RH-HI
17 H-LP LH-HI
18
STOP
ETCS
30 A
7.5 A
30 A
10 A
30 A
15 A
30 A
10 A
10 A
10 A
10 A
Ampere
10 A
30 A
15 A
10 A
30 A
10 A
10 A
Circuit
Air conditioning system
Trailer lights (tail lights)
Front fog lights
Stop lights, high mounted stoplight, vehicle stability control system, anti-lock brake system, shift lock system, multiport fuel injection system/sequential multiport fuel injection system, towing lights
Trailer brake controller
Multiport fuel injection system/ sequential multiport fuel injection system
Seat heaters
On-board diagnosis system
Trailer sub battery
AI system
Towing lights
Turn signal lights, emergency flashers, meter and gauge
Audio system
Right-hand headlight (low beam), front fog lights
Left-hand headlight (low beam)
Right-hand headlight (high beam)
Left-hand headlight (high beam), meter and gauge
Multiport fuel injection system/ sequential multiport fuel injection system, electronic throttle control system
4-3. Do-it-yourself maintenance
19
20
21
22
23
26
Fuse
ALT-S
EFI-MAIN
HORN
A/F HTR
ECU-B
24 DOME
25 RADIO NO.1
STA
27 Spare
28 Spare
29
30
S/HTR NO.1
J/B
31 AM1
32 HTR
33 ABS NO.1
Ampere
7.5 A
20 A
10 A
15 A
7.5 A
7.5 A
20 A
7.5 A
10 A
15 A
50 A
50 A
50 A
50 A
50 A
Circuit
Charging system
Multiport fuel injection system/ sequential multiport fuel injection system
Horn
Multiport fuel injection system/ sequential multiport fuel injection system
Wireless remote control system, air conditioning system, multiplex communication system, meter and gauge, front passenger occupant classification system, garage door opener
Interior light, personal lights, vanity lights
Audio system
Starting system, multiport fuel injection system/sequential multiport fuel injection system, meter and gauge, clutch start cancel switch
Spare fuse
Spare fuse
Seat heaters
TAIL, AC SKT, DR LCK, D FR P/W,
D RR P/W, P FR P/W and P RR
P/W fuses
ACC, IG1, IG1 NO.2, WIP, WSH,
4WD, BKUP LP and STA fuses
A/C fuse, air conditioning system
Anti-lock brake system, vehicle stability control system
449
4
4-3. Do-it-yourself maintenance
Fuse
34 AM2
35 AIR PMP
Ampere
30 A
50 A
Circuit
IGN and GAUGE fuses, multiport fuel injection system/sequential multiport fuel injection system
Multiport fuel injection system/ sequential multiport fuel injection system
36 ABS NO.2
37 INV
38 ALT
30 A
100 A
120 A*
140 A*
Anti-lock brake system, vehicle stability control system
Power outlets
AM1, AC SKT, HEATER, FR FOG,
STOP, OBD, J/B, TOWING TAIL,
TOWING BRK and BATT CHG fuses
*
: Replace the fuse with one of the same ampere rating as the original
450
■
Under the instrument panel
4-3. Do-it-yourself maintenance
1
2
3
IGN
Fuse
GAUGE
TAIL
4 ACC
5 PWR OUTLET
6 DR LCK
Ampere
15 A
7.5 A
10 A
7.5 A
15 A
20 A
Circuit
Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, traction control system, vehicle stability control system, SRS airbag system, front passenger occupant classification system
Meter and gauge, emergency flashers
Tail lights, license plate lights, parking lights, multiport fuel injection system/sequential multiport fuel injection system, instrument panel light control, illuminations
Shift lock system, outside rear view mirrors, audio system, power outlets
Power outlets
Door lock system
4
451
4-3. Do-it-yourself maintenance
7
Fuse
IG1 NO.2
8 BKUP LP
9 IG1
10 P RR P/W
11 P FR P/W
12 WSH
13 D RR P/W
14 4WD
15 WIP
16 D FR P/W
Ampere
10 A
10 A
10 A
20 A
20 A
10 A
20 A
20 A
30 A
30 A
Circuit
Anti-lock brake system, vehicle stability control system, stop lights, charging system, multiport fuel injection system/sequential multiport fuel injection system, air conditioning system, instrument panel light control, anti-glare inside rear view mirror, back monitor, clutch start cancel switch, rear differential lock system, power outlets, tire pressure warning system
Trailer lights (back-up lights)
Anti-lock brake system, traction control system, vehicle stability control system, back-up lights, air conditioning system, shift lock system, audio system
Rear passenger’s power window
(right side)
Front passenger’s power window
Wipers and washer
Rear passenger’s power window
(left side)
Four-wheel drive system, rear differential lock system
Wipers and washer
Power windows
452
4-3. Do-it-yourself maintenance
■ After a fuse is replaced
● If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (
● If the replaced fuse blows again, have the vehicle inspected by your
Toyota dealer.
■ If there is an overload in the circuits
The fuses are designed to blow, protecting the wiring harness from damage.
CAUTION
■ To prevent system breakdowns and vehicle fire
Observe the following precautions.
Failing to do so may cause damage to the vehicle, and possibly a fire or injury.
● Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse.
● Always use a genuine Toyota fuse or equivalent.
Never replace a fuse with a wire, even as a temporary fix.
● Do not modify the fuse or the fuse box.
4
NOTICE
■ Before replacing fuses
Have the cause of electrical overload determined and repaired by your Toyota dealer as soon as possible.
453
4-3. Do-it-yourself maintenance
Light bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer.
For more information about replacing other light bulbs, contact your
Toyota dealer.
■
Prepare a replacement light bulb
Check the wattage of the light bulb being replaced. (
■
Front bulb locations
Headlights Front side marker lights
Front turn signal lights/parking lights/daytime running lights
Front fog lights
(if equipped)
454
4-3. Do-it-yourself maintenance
■
Rear bulb locations
High mounted stoplight
Rear turn signal lights
Back-up lights
License plate lights
Stop/tail and rear side marker lights
(bulb type only)
Replacing light bulbs
■ Headlights
Unplug the connector.
4
455
4-3. Do-it-yourself maintenance
Remove the rubber cover.
Release the bulb retaining spring.
Remove the bulb.
To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.
456
4-3. Do-it-yourself maintenance
■
Front fog lights (if equipped)
Unplug the connector while pulling the lock release.
Turn the bulb counterclockwise.
4
457
4-3. Do-it-yourself maintenance
■
Front side marker lights
Turn the bulb base counterclockwise.
Remove the light bulb.
458
4-3. Do-it-yourself maintenance
■
Front turn signal lights/parking lights/daytime running lights
Turn the bulb base counterclockwise.
Remove the light bulb.
4
459
4-3. Do-it-yourself maintenance
■
Stop/tail lights, rear side marker lights (bulb type only), backup lights and rear turn signal lights
Remove the bolts and rear combination assembly.
Unplug the connector while depressing the lock release.
Turn the bulb bases counterclockwise.
Rear turn signal light
Stop/tail and rear side marker lights (bulb type only)
Back-up light
Remove the light bulb.
Rear turn signal light
Stop/tail and rear side marker lights (bulb type only)
Back-up light
460
4-3. Do-it-yourself maintenance
■
High mounted stoplight
Remove the screws and cover.
Remove the light bulbs.
4
461
4-3. Do-it-yourself maintenance
■
License plate lights
Remove the screw and light unit.
Turn the bulb base counterclockwise.
Remove the light bulb.
462
4-3. Do-it-yourself maintenance
■
Lights other than the above
If any of the lights listed below has burnt out, have it replaced by your Toyota dealer.
• Side turn signal lights (if equipped)
• Stop/tail lights (LED type)
• Rear side marker lights (LED type)
■ Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations:
● Large drops of water are built up on the inside of the lens.
● Water has built up inside the headlight.
■ LED light bulbs
The side turn signal lights (if equipped), stop/tail and rear side marker lights
(LED type) consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.
If two or more LEDs in a stop light burn out, your vehicle may not conform to local laws (SAE).
4
463
4-3. Do-it-yourself maintenance
CAUTION
■ Replacing light bulbs
● Turn off the headlights. Do not attempt to replace the bulb immediately after turning off the headlights.
The bulbs become very hot and may cause burns.
● Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
● Fully install light bulbs and any parts used to secure them. Failing to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.
■ To prevent damage or fire
Make sure bulbs are fully seated and locked.
464
When trouble arises
5
Emergency flashers ......... 466
If your vehicle needs to be towed ........................ 467
If you think something is wrong ............................. 474
Fuel pump shut off system ........................... 475
5-2. Steps to take in an emergency
If a warning light turns on or a warning buzzer sounds... ........................ 476
If you have a flat tire......... 486
If the engine will not start ................................ 501
If you lose your keys ........ 503
If the vehicle battery is discharged ..................... 504
If your vehicle overheats ....................... 508
If the vehicle becomes stuck .............................. 511
If your vehicle has to be stopped in an emergency ................ 513
465
5-1. Essential information
Emergency flashers
Use the emergency flashers if the vehicle malfunctions or is involved in an accident.
Press the switch to flash all the turn signal lights. To turn them off, press the switch once again.
NOTICE
■
To prevent battery discharge
Do not leave the emergency flashers on longer than necessary when the engine is not running.
466
5-1. Essential information
If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck.
Use a safety chain system for all towing, and abide by all state/provincial and local laws.
The wheels and axle on the ground must be in good condition.
If they are damaged, use a towing dolly or flat bed truck.
Before towing
The following may indicate a problem with your transmission. Contact your Toyota dealer before towing.
● The engine is running, but the vehicle will not move.
● The vehicle makes an abnormal sound.
Emergency towing (4WD models and PreRunner only)
If a tow truck is not available, in an emergency your vehicle may be temporarily towed using a cable or chain secured to the emergency towing hook. This should only attempted on hard, surfaced roads for short distances at low speeds.
A driver must be in the vehicle to steer and operate the brakes. The vehicle’s wheels, drive train, axles, steering and brakes must be in good condition.
Type A
Towing hook
5
467
5-1. Essential information
Type B
Towing hook
■ Emergency towing procedure
The engine switch must be in the ACC (engine off) or the ON
(engine running) position.
4WD models: Put the front-wheel drive control switch in H2.
Put the shift lever in N.
Release the parking brake.
CAUTION
■ Caution while towing
● Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive stress on the emergency towing hook and the cables or chains. Always be cautious of the surroundings and other vehicles while towing.
● If the engine is not running, the power assist for the brakes and steering will not function, making steering and braking more difficult.
468
5-1. Essential information
NOTICE
■ Emergency towing hook precautions
● Before emergency towing, check that the hook is not broken or damaged.
● Fasten the towing cable or chain securely to the hook.
● Do not jerk the hook. Apply steady and even force.
● To avoid damaging the hook, do not pull from the side or at a vertical angle. Always pull straight ahead.
Towing with a sling-type truck
NOTICE
■ To prevent body damage
Do not tow with a sling-type truck, either from the front or rear.
5
469
5-1. Essential information
Towing with a wheel lift-type truck from the front
Vehicles with an automatic transmission: Use a towing dolly under the rear wheels.
2WD models with a manual transmission: We recommend to use a towing dolly under the rear wheels.
When not using a towing dolly, release the parking brake and shift the shift lever to N.
4WD models with a manual transmission: We recommend to use a towing dolly under the rear wheels.
When not using a towing dolly, release the parking brake, shift the shift lever to N and put the front-wheel drive control switch in
H2.
NOTICE
■ To prevent causing serious damage to the transmission (vehicles with an automatic transmission)
Never tow this vehicle wheels on the ground.
470
5-1. Essential information
Towing with a wheel lift-type truck from the rear
2WD models
Turn the engine switch to the
ACC position.
4WD models
We recommend to use a towing dolly under the front wheels.
When not using a towing dolly, turn the engine switch to the ACC position, shift the shift lever to N and put the front-wheel drive control switch in H2.
5
NOTICE
■ To prevent damaging the vehicle
● Do not tow the vehicle with the key removed or in the LOCK position.
The steering lock mechanism is not strong enough to hold the front wheel straight.
● When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.
471
5-1. Essential information
Using a flat bed truck
Type A
If your Toyota is transported by a flat bed truck, it should be tied down at the locations shown in the illustration.
Front
472
Type B
5-1. Essential information
If your Toyota is transported by a flat bed truck, it should be tied down at the locations shown in the illustration.
Front
If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45
.
Do not overly tighten the tie downs or the vehicle may be damaged.
Apply the parking brake firmly.
5
473
5-1. Essential information
If you think something is wrong
If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible.
■
Visible symptoms
● Fluid leaks under the vehicle
(Water dripping from the air conditioning after use is normal.)
● Flat-looking tires or uneven tire wear
● Engine coolant temperature gauge needle continually points higher than normal
■
Audible symptoms
● Changes in exhaust sound
● Excessive tire squeal when cornering
● Strange noises related to the suspension system
● Pinging or other noises related to the engine
■
Operational symptoms
● Engine misfire, stumbling or running rough
● Appreciable loss of power
● Vehicle pulls heavily to one side when braking
● Vehicle pulls heavily to one side when driving on a level road
● Loss of brake effectiveness, spongy feeling, pedal almost touches the floor
474
5-1. Essential information
Fuel pump shut off system
To minimize the risk of fuel leakage when the engine stalls or an airbag inflates upon collision, the fuel pump shut off system stops supplying fuel to the engine.
Follow the procedure below to restart the engine after the system is activated.
Turn the engine switch to the ACC or LOCK position.
Restart the engine.
NOTICE
■
Before starting the engine
Inspect the ground under the vehicle.
If you find that fuel has leaked onto the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine.
5
475
5-2. Steps to take in an emergency
If a warning light turns on or a warning buzzer sounds...
Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system.
Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.
The following warning indicates a possible problem in the brake system. Immediately stop the vehicle in a safe place and contact your
Toyota dealer.
Warning light
(U.S.A.)
Warning light/Details
Brake system warning light (warning buzzer)
*
• Low brake fluid
• Malfunction in the brake system
This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released, the system is operating normally.
(Canada)
* : Parking brake engaged warning buzzer:
The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reached a speed of 3 mph [5 km/h])
476
5-2. Steps to take in an emergency
Stop the vehicle immediately.
The following warnings indicate the possibility of damage to the vehicle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.
Warning light Warning light/Details
Charging system warning light
Indicates a malfunction in the vehicle’s charging system.
Low engine oil pressure warning light
Indicates that the engine oil pressure is too low * .
*
: The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the engine oil level dipstick.
Have the vehicle inspected immediately.
Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident.
Have the vehicle inspected by your Toyota dealer immediately.
5
Warning light
(U.S.A.)
(Canada)
Warning light/Details
Malfunction indicator lamp
Indicates a malfunction in:
• The electronic engine control system;
• The electronic throttle control system;
• The electronic automatic transmission control system; or
• Emission control system.
SRS warning light
Indicates a malfunction in:
• The SRS airbag system;
• The front passenger occupant classification system; or
• The seat belt pretensioner system.
477
5-2. Steps to take in an emergency
Warning light
(U.S.A.)
Warning light/Details
ABS warning light
Indicates a malfunction in:
• The ABS; or
• The brake assist system.
(Canada)
Slip indicator
The indicator comes on to indicate a malfunction in:
• The VSC;
• The TRAC;
• The active traction control system (if equipped);
• The AUTO LSD system;
• The downhill assist control system (if equipped);
• The hill-start assist control system (if equipped); or
• The Trailer Sway Control (if equipped).
Cruise control indicator light (if equipped)
Indicates a malfunction in the cruise control system.
(Flashes)
478
5-2. Steps to take in an emergency
Follow the correction procedures.
After taking the specified steps to correct the suspected problem, check that the warning light turns off.
Warning light
(On the instrument cluster)
(On the center panel)
Warning light/Details
Open door warning light
Indicates that a door is not fully closed.
Driver’s seat belt reminder light
(warning buzzer)
* 1
Warns the driver to fasten his/her seat belt.
Front passenger’s seat belt reminder light
(warning buzzer)
* 1
Warns the front passenger to fasten his/her seat belt.
Automatic transmission fluid temperature warning light (if equipped)
When the light comes on:
Indicates that the automatic transmission fluid temperature is too high.
Correction procedure
Check that all doors are closed.
Fasten the seat belt.
Fasten the seat belt.
When the light flashes:
Indicates a malfunction in the automatic transmission system.
Stop the vehicle in a safe place, shift the shift lever to P and wait until the light goes off.
If the light goes off, you may start the vehicle again. If the light does not go off, contact your Toyota dealer.
Have the system checked by your Toyota dealer.
479
5
5-2. Steps to take in an emergency
Warning light Warning light/Details
Tire pressure warning light
Correction procedure
When the light comes on:
Low tire inflation pressure such as
• Natural causes
(
P. 482)
• Flat tire (
• When the light stays on after blinking for 1 minute: Malfunction in the tire pressure warning system. (
P. 483)
Adjust the tire inflation pressure to the specified level.
The light will turn off after a few minutes.
In case the light does not turn off even if the tire inflation pressure is adjusted, have the system checked by your Toyota dealer.
Have the system checked by your
Toyota dealer.
Low fuel level warning light
Low level of fuel.
Refuel the vehicle.
480
5-2. Steps to take in an emergency
Warning light
(U.S.A.)
Warning light/Details
Maintenance required reminder light
Indicates that maintenance is required according to the driven distance on the maintenance schedule.
* 2
Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the reminder light has been reset.
Correction procedure
If necessary, perform maintenance.
Comes on and remains on if the distance driven exceeds 5000 miles
(8000 km) after the reminder light has been reset.
(The indicator will not work properly unless the reminder light has been reset.)
Perform the necessary maintenance.
Please reset the reminder light after the maintenance is performed. (
* 1
: Driver’s and front passenger’s seat belt buzzer:
The driver’s and front passenger’s seat belt buzzer sounds to alert the driver and front passenger that their seat belt is not fastened. Once the engine switch is turned to the ON or START position, the buzzer sounds for 6 seconds. The buzzer sounds once if the driver’s or front passenger’s seat belt is unfastened when the vehicle reaches a speed of 12 mph (20 km/h). Then, if the seat belt is still unfastened after 30 seconds elapse, the buzzer will sound intermittently for approximately 10 seconds, followed by a different tone for approximately 20 more seconds.
* 2
: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual
Supplement” for the maintenance interval applicable to your vehicle.
5
481
5-2. Steps to take in an emergency
■ Key reminder buzzer
The buzzer indicates that the key has not been removed (with the engine switch in the ACC or LOCK position and the driver’s door opened).
■ If the malfunction indicator lamp comes on while driving
First check the following:
● Is your vehicle low on gas?
If it is, refuel the vehicle immediately.
● Is the fuel tank cap loose?
If it is, tighten it securely.
The light will go off after taking several driving trips.
If the light does not go off even after several trips, contact your Toyota dealer as soon as possible.
■ Front passenger detection sensor and passenger seat belt reminder
If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light to flash and buzzer to sound.
■ When the tire pressure warning light comes on
Check the tire inflation pressure and adjust to the appropriate level.
Pushing the tire pressure warning reset switch does not turn off the tire pressure warning light.
■ The tire pressure warning light may turn on due to natural causes
The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temperature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).
■ When a tire is replaced with a spare tire
The temporary spare tire is not equipped with the tire pressure warning valve and transmitter. If a tire goes flat, the tire pressure warning light will not turn off even though the flat tire is replaced with the temporary spare tire. Replace the temporary spare tire with the repaired tire and adjust the proper tire inflation pressure. The tire pressure warning light will turn off after a few minutes.
482
5-2. Steps to take in an emergency
■ If the tire pressure warning system is inoperative
The tire pressure warning system will be disabled in the following conditions:
(When the condition becomes normal, the system will work properly.)
● If tires not equipped with tire pressure warning valves and transmitters are used.
● If the ID code on the tire pressure warning valves and transmitters is not registered in the tire pressure warning computer.
● If the tire inflation pressure is 73 psi (500 kPa, 5.1 kgf/cm
2
or bar) or higher.
The tire pressure warning system may be disabled in the following conditions:
(When the condition becomes normal, the system will work properly.)
● If electronic devices or facilities using similar radio wave frequencies are nearby.
● If a radio set at similar frequencies is in use in the vehicle.
● If a window tint that affects the radio wave signals is installed.
● If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings.
● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.)
● If tire chains are used.
■ If the tire pressure warning light frequently comes on after blinking for 1 minute
If the tire pressure warning light frequently comes on after blinking for 1 minute when the engine switch is turned to the ON position, have it checked by your Toyota dealer.
■ Customization that can be configured at Toyota dealer
The vehicle speed linked seat belt reminder buzzer can be disabled.
(Customizable features
5
483
5-2. Steps to take in an emergency
CAUTION
■ If the tire pressure warning light comes on
Be sure to observe the following precautions. Failure to do so could cause loss of vehicle control and result in death or serious injury.
● Stop your vehicle in a safe place as soon as possible. Adjust the tire inflation pressure immediately.
● If the tire pressure warning light comes on even after tire inflation pressure adjustment, it is probable that you have a flat tire. Check the tires.
If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer.
● Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes.
■ If a blowout or sudden air leakage should occur
The tire pressure warning system may not activate immediately.
■ Maintenance of the tire
Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label). (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label [tire and load information label], you should determine the proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS-tire pressure warning system) that illuminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale (tire pressure warning light) illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure.
Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
484
5-2. Steps to take in an emergency
CAUTION
■ Maintenance of the tire
Please note that the TPMS (tire pressure warning system) is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale (tire pressure warning light).
Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operating properly. The TPMS (tire pressure warning system) malfunction indicator is combined with the low tire pressure telltale (tire pressure warning light). When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended.
TPMS (tire pressure warning system) malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS (tire pressure warning system) from functioning properly. Always check the TPMS (tire pressure warning system) malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS (tire pressure warning system) to continue to function properly.
5
NOTICE
■ To ensure the tire pressure warning system operates properly
Do not install tires with different specifications or makers, as the tire pressure warning system may not operate properly.
485
5-2. Steps to take in an emergency
If you have a flat tire
Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire.
■
Before jacking up the vehicle
● Stop the vehicle on a hard, flat surface.
● Set the parking brake.
● Shift the shift lever to P (automatic transmission) or R (manual transmission).
● Stop the engine.
● Turn on the emergency flashers.
■
Location of the spare tire
■
Location of the jack and tools
Access Cab models
Tool bag
Jack
486
Double Cab models
Tool bag
Jack
5-2. Steps to take in an emergency
Taking out the jack and tool bag
Access Cab models
Vehicles with rear seats:
Pull up the lever.
Raise the bottom cushion up.
5
Turn the knob counterclockwise.
487
5-2. Steps to take in an emergency
Open the lid.
Vehicles with rear seats: Press the lid against the bottom of the lower cushion until it is supported by the hook-andloop fastener.
Make sure that the lid is supported to prevent it from closing unexpectedly.
Unhook the strap and remove the tool bag.
Loosen and remove the jack.
Loosen
Tighten
488
Double Cab models
5-2. Steps to take in an emergency
Swing the bottom cushion up by pulling the lock release strap.
Turn the knob counterclockwise.
Open the lid.
Unhook the strap and remove the tool bag.
5
Loosen and remove the jack.
Loosen
Tighten
489
5-2. Steps to take in an emergency
Assemble the jack handle (in the tool bag)
Assemble the jack handle extension as shown.
Taking out the spare tire
Insert the end of the jack handle extension into the lowering screw and turn it counterclockwise.
After the tire is lowered completely to the ground, remove the holding bracket.
490
Replacing a flat tire
5-2. Steps to take in an emergency
Chock the tires.
Flat tire
Left-hand side
Wheel chock positions
Behind the rear righthand side tire
Front
Right-hand side
Behind the rear left-hand side tire
Left-hand side
In front of the front righthand side tire
Rear
Right-hand side
In front of the front lefthand side tire
Slightly loosen the wheel nuts
(one turn).
5
Assemble the jack handle extension as shown.
491
5-2. Steps to take in an emergency
Front
Installing the tire
Position the jack at the correct jack point as shown.
Front
Rear
Make sure the jack is positioned on a level and solid place.
Raise the vehicle until the tire is slightly raised off the ground.
When positioning the jack under the rear axle housing, make sure the groove on the top of the jack fits with the rear axle housing.
Remove all the wheel nuts and the tire.
When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.
Remove any dirt or foreign matter from the wheel contact surface.
If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
492
5-2. Steps to take in an emergency
Install the tire and loosely tighten each wheel nut by hand by approximately the same amount.
Replacing a steel wheel with a steel wheel
Tapered portion
Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.
Disc wheel sheet
Replacing an aluminum wheel with a steel wheel
Tapered portion
Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.
Disc wheel sheet
Replacing an aluminum wheel with an aluminum wheel
Washer
Tighten the nuts until the washer of the nut comes into loose contact with the disc wheel.
5
Disc wheel
493
5-2. Steps to take in an emergency
Lower the vehicle.
Firmly tighten each nut two or three times in the order shown in the illustration.
Tightening torque:
83 ft·lbf (113 N·m, 11.5 kgf·m)
2WD models except PreRunner
4WD models and PreRunner
494
5-2. Steps to take in an emergency
CAUTION
■ Stowing the flat tire
Failure to follow steps listed under stowing the tire may result in damage to the spare tire carrier and loss of the tire, which could result in serious injury or death.
Stowing the flat tire, jack and all tools
Remove the center wheel ornament by pushing from the reverse side.
Lay down the tire with the valve stem facing up and install the holding bracket, inserting the claw into the wheel lug nut hole.
Turn the jack handle extension clockwise to take up slack in the chain. incorrect
Then, check to ensure the claw is in the wheel lug nut hole and the holding bracket is centered in the wheel hub.
correct
Holding bracket
Claw (Claw on 4WD and Pre-
Runner only)
While raising, secure the tire, taking care that the tire goes straight up without catching on any surrounding parts, to prevent it from flying forward during a collision or sudden braking.
Tightening torque:
27.6 ft·lbf (37.4 N·m, 3.8 kgf·m)
5
495
5-2. Steps to take in an emergency
Confirm that the tire is not loose after tightening:
Push and pull the tire
Try rotating
Visually check to ensure the tire is not hung on surrounding parts.
If looseness or misassembly exists, repeat step 2 and step 3.
Repeat step 3 any time the tire is lowered or disturbed.
Stow the tools and jack securely.
■ After completing the tire change
The tire pressure warning system must be reset. (
■ When using the temporary spare tire
As the temporary spare tire is not equipped with the tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be warned. Also, if you replace the temporary spare tire after the tire pressure warning light comes on, the light remains on.
496
5-2. Steps to take in an emergency
CAUTION
■ Using the jack
Improper use of the jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack.
● Do not use the jack for any purpose other than replacing tires or installing and removing tire chains.
● Only use the jack that comes with this vehicle for replacing a flat tire.
Do not use it on other vehicles, and do not use other jacks for replacing tires on this vehicle.
● Always check that the jack is securely set to the jack point.
● Do not put any part of your body under the vehicle supported by a jack.
● Do not start or run the engine while your vehicle is supported by the jack.
● Do not raise the vehicle while someone is in it.
● When raising the vehicle, do not put an object on or under the jack.
● Do not raise the vehicle to a height greater than that required to replace the tire.
● Use a jack stand if it is necessary to get under the vehicle.
Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle will be injured.
■ Using the jack handle
Tighten all the screws securely to prevent the extension parts from coming apart unexpectedly.
■ Replacing a flat tire
● Observe the following precautions.
Failure to do so may result in serious injury:
• Lower the spare tire completely to the ground before removing it from under the vehicle.
• Do not try to remove the wheel ornament by hand. Take due care in handling the ornament to avoid unexpected personal injury.
5
497
5-2. Steps to take in an emergency
CAUTION
■ Replacing a flat tire
• Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc. may result in burns.
● Failure to follow these precautions could cause the wheel nuts to loosen and the tire to fall off, resulting in death or serious injury.
• Have the wheel nuts tightened with a torque wrench to 83 ft·lbf
(113 N·m, 11.5 kgf·m) as soon as possible after changing wheels.
• When installing a tire, only use wheel nuts that have been specifically designed for that wheel.
• If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer.
• Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
• When installing the wheel nuts, be sure to install them with the tapered ends facing inward. (
■ When using the temporary spare tire
● Remember that your temporary spare tire is specifically designed for use with your vehicle. Do not use your temporary spare tire on another vehicle.
● Do not use two temporary spare tires simultaneously.
● Replace the temporary spare tire with a standard tire as soon as possible.
● Avoid sudden acceleration, deceleration and braking, as well as sharp cornering.
498
5-2. Steps to take in an emergency
CAUTION
■ Speed limit when using the temporary spare tire
Do not drive at speeds in excess of 50 mph (80 km/h) when a temporary spare tire is installed on the vehicle.
The temporary spare tire is not designed for driving at high speeds. Failing to observe this precaution may lead to an accident causing death or serious injury.
■ Driving with tire chains and the temporary spare tire
Do not fit tire chains to the temporary spare tire.
Tire chains may damage the vehicle body and adversely affect driving performance.
■ When the spare tire is attached
The vehicle speed may not be correctly detected, and the following systems may not operate correctly:
● ABS & Brake assist
● VSC
● TRAC
● Active traction control system (if equipped)
● Hill-start assist control system (if equipped)
● Downhill assist control system (if equipped)
● AUTO LSD system
● Cruise control (if equipped)
Also, not only can the following system not be utilized fully, it may actually negatively effect the drive-train components:
● 4WD system
5
499
5-2. Steps to take in an emergency
NOTICE
■ Do not drive the vehicle with a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.
■ When stowing the flat tire
Ensure that there is no object caught between the tire and the vehicle underbody.
■ When replacing the tires
● When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly.
● Replace the grommets for the tire pressure warning valves and transmitters as well.
■ To avoid damage to the tire pressure warning valves and transmitters
When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (
500
5-2. Steps to take in an emergency
If the engine will not start
If the engine still does not start after following the correct starting procedure (
P. 131) or releasing the steering lock (P. 132), confirm
the following points.
■
The engine will not start even when the starter motor operates normally.
One of the following may be the cause of the problem.
● There may not be sufficient fuel in the vehicle’s tank.
Refuel the vehicle.
● The engine may be flooded.
Try to restart the engine once more following correct starting procedures.
● There may be a malfunction in the engine immobilizer system.
(
■
The starter motor turns over slowly, the interior lights and headlights are dim, or the horn does not sound or sounds at a low volume.
One of the following may be the cause of the problem.
● The battery may be discharged. (P. 504)
● The battery terminal connections may be loose or corroded.
■
The starter motor does not turn over, the interior lights and headlights do not turn on, or the horn does not sound.
One of the following may be the cause of the problem.
● One or both of the battery terminals may be disconnected.
● The battery may be discharged. (P. 504)
Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.
5
501
5-2. Steps to take in an emergency
If the shift lever cannot be shifted from P (vehicles with an automatic transmission)
If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately.
The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Set the parking brake.
Turn the engine switch to the ACC or ON position.
Depress the brake pedal.
Pry the cover up with a flathead screwdriver or equivalent.
Press the shift lock override button.
The shift lever can be shifted while the button is pressed.
502
5-2. Steps to take in an emergency
If you lose your keys
New genuine Toyota keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate.
503
5
5-2. Steps to take in an emergency
If the vehicle battery is discharged
The following procedures may be used to start the engine if the vehicle’s battery is discharged.
You can call your Toyota dealer or qualified repair shop.
If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your Toyota following the steps below.
Connect the jumper cables.
2.7 L 4-cylinder (2TR-FE) engine
504
4.0 L V6 (1GR-FE) engine
5-2. Steps to take in an emergency
Positive (+) battery terminal on your vehicle
Positive (+) battery terminal on the second vehicle
Negative (-) battery terminal on the second vehicle
Connect the jumper cable to ground on your vehicle as shown in the illustration.
Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5 minutes to recharge the battery of your vehicle.
Maintain the engine speed of the second vehicle and start the vehicle’s engine.
Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were connected.
Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.
5
505
5-2. Steps to take in an emergency
■ Starting the engine when the battery is discharged (vehicles with an automatic transmission)
The engine cannot be started by push-starting.
■ Avoiding a discharged battery
● Turn off the headlights and the audio system while the engine is turned off.
● Turn off any unnecessary electrical components when the vehicle is running at a low speed for an extended period, such as in heavy traffic, etc.
■ Charging the battery
The electricity stored in the battery will discharge gradually even when the vehicle is not in use, due to natural discharge and the draining effects of certain electrical appliances. If the vehicle is left for a long time, the battery may discharge, and the engine may be unable to start. (The battery recharges automatically during driving.)
CAUTION
■ Avoiding battery fires or explosions
Observe the following precautions to prevent accidentally igniting the flammable gas that may be emitted from the battery.
● Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended terminal.
● Do not allow the jumper cables to come into contact with the “+” and “-” terminals.
● Do not smoke, use matches, cigarette lighters or allow open flame near the battery.
506
5-2. Steps to take in an emergency
CAUTION
■ Battery precautions
The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following precautions when handling the battery.
● When working with the battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.
● Do not lean over the battery.
● In the event that battery fluid comes into contact with the skin or eyes, immediately wash the affected area with water and seek medical attention.
Place a wet sponge or cloth over the affected area until medical attention can be received.
● Always wash your hands after handling the battery support, terminals, and other battery-related parts.
● Do not allow children near the battery.
NOTICE
■ To prevent damaging the vehicle (vehicles with a manual transmission)
Do not pull- or push-start the vehicle, because the three-way catalytic converter may overheat and become a fire hazard.
■ When handling jumper cables
Be careful that the jumper cables do not become tangled in the cooling fan or any of the belts when connecting or disconnecting them.
5
507
5-2. Steps to take in an emergency
If your vehicle overheats
The following may indicate that your vehicle is overheating.
● The needle of the engine coolant temperature gauge (P. 145)
enters the red zone or a loss of engine power is experienced.
(For example, the vehicle speed does not increase.)
● Steam comes out from under the hood.
Correction procedures
Stop the vehicle in a safe place and turn off the air conditioning system, and then stop the engine.
If you see steam:
Carefully lift the hood after the steam subsides completely.
If you do not see steam:
Carefully lift the hood.
After the engine has cooled down sufficiently, inspect the hoses and radiator core (radiator) for any leaks.
Radiator
Cooling fan
If a large amount of coolant leaks, immediately contact your Toyota dealer.
The coolant level is satisfactory if the reservoir level is between the
“FULL” and “LOW” lines on the reservoir.
Reservoir
“FULL”
“LOW”
Radiator cap
508
5-2. Steps to take in an emergency
Add coolant if necessary.
Water can be used in an emergency if coolant is unavailable.
Start the engine to check that the radiator cooling fan operates and check for coolant leaks from the radiator or hoses.
If the fan is not operating:
Stop the engine immediately and contact your Toyota dealer.
If the fan is operating:
Have the vehicle inspected at the nearest Toyota dealer.
CAUTION
■ To prevent an accident or injury when inspecting under the hood of your vehicle
●
If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, causing serious injuries such as burns.
● Keep hands and clothing (especially a tie, a scarf or a muffler) away from the fan and belts. Failure to do so may cause the hands or clothing to be caught, resulting in serious injury.
● Do not loosen the radiator cap and the coolant reservoir cap while the engine and radiator are hot.
Serious injury, such as burns, may result from hot coolant and steam released under pressure.
5
509
5-2. Steps to take in an emergency
NOTICE
■ When adding engine coolant
Wait until the engine has cooled down before adding engine coolant.
When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.
■ To prevent damage to the cooling system
Observe the following precautions:
● Avoid contaminating the coolant with foreign matter (such as sand or dust etc.).
● Do not use any coolant additives.
510
5-2. Steps to take in an emergency
If the vehicle becomes stuck
Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow.
Stop the engine. Set the parking brake and put the shift lever in P (vehicles with an automatic transmission) or N
(vehicles with a manual transmission).
Remove the mud, snow, or sand from around the stuck tire.
Place wood, stones or some other material to help provide traction under the tires.
Restart the engine.
Turn off the VSC. (
Shift the shift lever to D or R (automatic transmission) or 1 or R (manual transmission) and carefully apply the accelerator to free the vehicle.
CAUTION
■ When attempting to free a stuck vehicle
If you choose to rock the vehicle back and forth to free it, make sure the surrounding area is clear, to avoid striking other vehicles, objects or persons.
The vehicle may also lunge forward or back suddenly as it becomes free.
Use extreme caution.
■ When shifting the shift lever
Vehicles with an automatic transmission: Be careful not to shift the shift lever with the accelerator pedal depressed.
This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.
5
511
5-2. Steps to take in an emergency
NOTICE
■ To avoid damaging the transmission and other components
● Avoid spinning the wheels and do not rev up the engine.
● If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed.
512
5-2. Steps to take in an emergency
If your vehicle has to be stopped in an emergency
Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following procedure:
Steadily step on the brake pedal with both feet and firmly depress it.
Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle.
Shift the shift lever to N.
If the shift lever is shifted to N
After slowing down, stop the vehicle in a safe place by the road.
Stop the engine.
If the shift lever cannot be shifted to N
Keep depressing the brake pedal with both feet to reduce vehicle speed as much as possible.
Stop the engine by turning the engine switch to the ACC position.
5
Stop the vehicle in a safe place by the road.
513
5-2. Steps to take in an emergency
CAUTION
■ If the engine has to be turned off while driving
● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn.
Decelerate as much as possible before turning off the engine.
● Never attempt to remove the key, as doing so will lock the steering wheel.
514
5-2. Steps to take in an emergency
515
5
5-2. Steps to take in an emergency
516
Vehicle specifications
6
(fuel, oil level, etc.) ......... 516
Fuel information ............... 537
Tire information ................ 540
Customizable features ..... 551
Items to initialize .............. 552
515
6-1. Specifications
Maintenance data (fuel, oil level, etc.)
Dimensions
2WD models except PreRunner
Cab type
Overall length
Overall width
Overall height
Wheelbase
Front tread
Rear tread
*
Access Cab
Except
X-Runner
208.1 in.
(5285 mm)
72.2 in.
(1835 mm)
66.1 in.
(1680 mm)
X-Runner
208.5 in.
(5295 mm)
74.0 in.
(1880 mm)
61.0 in.
(1550 mm)
61.0 in.
(1550 mm)
65.6 in.
(1665 mm)
127.4 in. (3235 mm)
62.2 in.
(1580 mm)
62.2 in.
(1580 mm)
*
: Unladen vehicle
Double Cab
208.1 in.
(5285 mm)
74.6 in.
(1895 mm)
66.1 in.
(1680 mm)
61.0 in.
(1550 mm)
61.0 in.
(1550 mm)
516
6-1. Specifications
4WD models and PreRunner
Cab type
Overall length
Overall width
Overall height
* 1
Wheelbase
Front tread
Rear tread
Access Cab
208.1 in. (5285 mm)
74.6 in. (1895 mm)
70.3 in. (1785 mm)
127.4 in. (3235 mm)
63.0 in. (1600 mm)
63.4 in. (1610 mm)
* 2
63.2 in. (1605 mm)
63.6 in. (1615 mm) * 2
Overall height * 1
Cab type
Overall length
Overall width
2.7 L 4-cylinder
(2TR-FE) engine
4.0 L V6
(1GR-FE) engine
Double Cab
With short deck With long deck
208.1 in. (5285 mm) 221.3 in. (5620 mm)
74.6 in. (1895 mm)
70.3 in. (1785 mm)
70.1 in. (1780 mm)
Wheelbase
Front tread
Rear tread
127.4 in. (3235 mm) 140.6 in. (3570 mm)
63.0 in. (1600 mm)
63.4 in. (1610 mm)
* 2
63.4 in. (1610 mm)
63.8 in. (1620 mm)
* 2
6
* 1
:Unladen vehicle
* 2
:P265/60R18 tires
517
6-1. Specifications
Vehicle capacity weight
2WD models except PreRunner
Cab type Engine Deck type
Vehicle capacity weight (Occupant + luggage) *
Access Cab
Double Cab
2.7 L 4-cylinder
(2TR-FE) engine
4.0 L V6
(1GR-FE) engine
2.7 L 4-cylinder
(2TR-FE) engine
Long deck
1050 lb. (475 kg)
850 lb. (385 kg)
950 lb. (430 kg)
*
: Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your
Toyota dealer about the weight of accessory parts.
PreRunner
Cab type Engine Deck type
Vehicle capacity weight (Occupant
+ luggage)
*
2.7 L 4-cylinder
(2TR-FE) engine
1300 lb. (585 kg)
Access Cab Long deck
4.0 L V6
(1GR-FE) engine
1250 lb. (565 kg)
2.7 L 4-cylinder
(2TR-FE) engine
1300 lb. (585 kg)
Short deck
Double Cab
4.0 L V6
(1GR-FE) engine
1150 lb. (520 kg)
Long deck
* : Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your
Toyota dealer about the weight of accessory parts.
518
6-1. Specifications
4WD models
Cab type Engine Deck type
Vehicle capacity weight (Occupant
+ luggage)
*
Access Cab
2.7 L 4-cylinder
(2TR-FE) engine
4.0 L V6
(1GR-FE) engine
Long deck
1200 lb. (540 kg)
1140 lb. (515 kg)
Double Cab
4.0 L V6
(1GR-FE) engine
Short deck
Long deck
1040 lb. (470 kg)
*
: Installing accessories in addition to those installed at the factory increases vehicle weight, thereby reducing vehicle capacity weight. Contact your
Toyota dealer about the weight of accessory parts.
TWR (Trailer Weight Rating)
Access Cab models
Driving system
TWR Model code * 1
TRN225L-CRMDKA
TRN225L-CRPDKA
TRN245L-CRMDKA
TRN245L-CRPDKA
TRN265L-CRPDKA
GRN225L-CRFDKA
Engine
2.7 L 4-cylinder
(2TR-FE) engine
2WD
4WD
2WD
3500 lb. (1585 kg)
GRN245L-CRADKA
GRN245L-CRFDKA
4.0 L V6 (1GR-FE) engine
GRN265L-CRADKA
4WD
2WD
3300 lb. (1495 kg)
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg) * 3
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg)
* 3
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg) * 3
519
6
6-1. Specifications
Double Cab models
Model code
* 1
Engine
Driving system
TWR
TRN225L-PRPDKA
TRN265L-PRPDKA
GRN245L-PRADKA
GRN245L-PRFDKA
GRN250L-PRADKA
GRN265L-PRADKA
GRN270L-PRADKA
2.7 L 4-cylinder
(2TR-FE) engine
4.0 L V6 (1GR-FE) engine
2WD
4WD
2WD
3400 lb. (1540 kg)
3500 lb. (1585 kg)
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg)
* 3
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg) * 3
3400 lb. (1540 kg)
* 2
6200 lb. (2810 kg)
* 3
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg) * 3
3500 lb. (1585 kg)
* 2
6500 lb. (2945 kg)
* 3
* 1
: The model code is indicated on the Certification Label. (
* 2
: Without towing package
* 3
: With towing package
520
6-1. Specifications
Vehicle identification
■ Vehicle identification number
The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.
This number is stamped on the top left of the instrument panel.
Access Cab models
This number is also on the
Certification Label.
Double Cab models
This number is also on the
Certification Label.
6
521
6-1. Specifications
■
Engine number
The engine number is stamped on the engine block as shown.
2.7 L 4-cylinder (2TR-FE) engine
4.0 L V6 (1GR-FE) engine
522
6-1. Specifications
Engine
2.7 L 4-cylinder (2TR-FE) engine
Model
Type
Bore and stroke
Displacement
Drive belt tension
Valve clearance
(engine cold)
Intake
Exhaust
2TR-FE
4-cylinder in line, 4-cycle, gasoline
3.74
3.74 in. (95.0 95.0 mm)
164.3 cu.in.
(2694 cm
3
)
Automatic adjustment
Automatic adjustment
4.0 L V6 (1GR-FE) engine
Model
Type
Bore and stroke
Displacement
Drive belt tension
Valve clearance
(engine cold)
Intake
Exhaust
1GR-FE
6-cylinder V type, 4-cycle, gasoline
3.70
3.74 in. (94.0 95.0 mm)
241.4 cu.in.
(3956 cm
3
)
Automatic adjustment
0.006
0.010 in. (0.15 0.25 mm)
0.011
0.015 in. (0.29 0.39 mm)
Fuel
Fuel type
Octane Rating
Fuel tank capacity
(Reference)
Unleaded gasoline only
87 (Research Octane Number 91) or higher
21.1 gal. (80.0 L, 17.6 lmp.gal.)
6
523
6-1. Specifications
Lubrication system
Oil capacity
(Drain and refill - reference
*
)
Without filter 2.7 L 4-cylinder (2TR-FE) engine
5.4 qt. (5.1 L, 4.5 Imp.qt.)
4.0 L V6 (1GR-FE) engine
2WD models except PreRunner:
4.4 qt. (4.2 L, 3.7 Imp.qt.)
4WD models and PreRunner:
5.2 qt. (4.9 L, 4.3 Imp.qt.)
With filter 2.7 L 4-cylinder (2TR-FE) engine
6.1 qt. (5.8 L, 5.1 Imp.qt.)
4.0 L V6 (1GR-FE) engine
2WD models except PreRunner:
4.8 qt. (4.5 L, 4.0 Imp.qt.)
4WD models and PreRunner:
5.5 qt. (5.2 L, 4.6 Imp.qt.)
*
: The engine oil capacity is a reference quantity to be used when changing the engine oil. Warm up and turn off the engine, wait more than 5 minutes, and check the oil level on the dipstick.
524
6-1. Specifications
■
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use
Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity.
Oil grade: ILSAC GF-5 multigrade engine oil
Recommended viscosity:
2.7 L 4-cylinder (2TR-FE) engine
SAE 0W-20
Outside temperature
SAE 0W-20 is the best choice for good fuel economy and good starting in cold weather.
If SAE 0W-20 is not available,
SAE 5W-20 oil may be used.
However, it must be replaced with SAE 0W-20 at the next oil change.
Oil viscosity (0W-20 is explained here as an example):
● The 0W in 0W-20 indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.
● The 20 in 0W-20 indicates the viscosity characteristic of the oil when the oil is at high temperature. An oil with a higher viscosity (one with a higher value) may be better suited if the vehicle is operated at high speeds, or under extreme load conditions.
6
525
6-1. Specifications
4.0 L V6 (1GR-FE) engine
SAE 5W-30
Outside temperature
SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather.
If SAE 5W-30 is not available,
SAE 10W-30 oil may be used.
However, it should be replaced with SAE 5W-30 at the next oil change.
Oil viscosity (5W-30 is explained here as an example):
● The 5W in 5W-30 indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.
● The 30 in 5W-30 indicates the viscosity characteristic of the oil when the oil is at high temperature. An oil with a higher viscosity (one with a higher value) may be better suited if the vehicle is operated at high speeds, or under extreme load conditions.
How to read oil container label:
The International Lubricant Specification Advisory Committee
(ILSAC) Certification Mark is added to some oil containers to help you select the oil you should use.
526
6-1. Specifications
Cooling system
Capacity
2.7 L 4-cylinder (2TR-FE) engine
4.0 L V6 (1GR-FE) engine
Coolant type
Vehicles with an automatic transmission
9.1 qt. (8.6 L, 7.6 Imp.qt.)
Vehicles with a manual transmission
9.2 qt. (8.7 L, 7.7 Imp.qt.)
Vehicles with an automatic transmission
10.1 qt. (9.6 L, 8.4 Imp.qt.)
Vehicles with a manual transmission
10.3 qt. (9.7 L, 8.5 Imp.qt.)
Use either of the following.
• “Toyota Super Long Life Coolant”
• Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology
Do not use plain water alone.
Ignition system
Spark plug
2.7 L 4-cylinder (2TR-FE) engine
Make DENSO
Gap
4.0 L V6 (1GR-FE) engine
Make DENSO
NGK
Gap
SK20HR-A11
0.043 in. (1.1 mm)
K20HR-U11
LFR6C11
0.043 in. (1.1 mm)
6
NOTICE
■ Iridium-tipped spark plugs (2.7 L 4-cylinder [2TR-FE] engine only)
Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine.
527
6-1. Specifications
Electrical system
Battery
Open voltage at
68
F (20C):
Charging rates
12.6
12.8 V Fully charged
12.2
12.4 V Half charged
11.8
12.0 V Discharged
(Voltage checked 20 minutes after the key is removed with all the lights turned off)
5 A max.
Differential
Front
(4WD models)
1.59 qt. (1.50 L, 1.32 Imp.qt.)
Oil capacity
Rear
Oil type and viscosity
*
2WD models except PreRunner
3.66 qt. (3.46 L, 3.04 Imp.qt.)
4WD models and PreRunner
3.12 qt. (2.95 L, 2.60 Imp.qt.)
Toyota Genuine Differential Gear Oil LT
75W-85 GL-5 or equivalent
* : Your Toyota vehicle is filled with “Toyota Genuine Differential Gear Oil” at the factory. Use Toyota approved “Toyota Genuine Differential Gear Oil” or an equivalent oil of matching quality to satisfy the above specification. Please contact your Toyota dealer for further details.
528
6-1. Specifications
Automatic transmission
4-speed models
Fluid capacity *
Fluid type
10.8 qt. (10.2 L, 9.0 Imp.qt.)
Toyota Genuine ATF Type T-IV
5-speed models
Fluid capacity *
Vehicles without towing package
11.3 qt. (10.7 L, 9.4 Imp.qt.)
Vehicles with towing package
11.5 qt. (10.9 L, 9.6 Imp.qt.)
Toyota Genuine ATF WS Fluid type
*
: The fluid capacity is the quantity of reference. If replacement is necessary, contact your Toyota dealer.
NOTICE
■ Automatic transmission fluid type (4-speed models)
Using automatic transmission fluid other than “Toyota Genuine ATF Type
T-IV” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmission of your vehicle.
■ Automatic transmission fluid type (5-speed models)
Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmission of your vehicle.
6
529
6-1. Specifications
Manual transmission
Gear oil capacity (Reference)
2.7 L 4-cylinder (2TR-FE) engine
4.0 L V6 (1GR-FE) engine
Gear oil type
Recommended gear oil viscosity
2WD models
2.7 qt. (2.6 L, 2.3 Imp.qt.)
4WD models
2.3 qt. (2.2 L, 1.9 Imp.qt.)
1.9 qt. (1.8 L, 1.6 Imp.qt.)
Gear oil API GL-3 (GL-4)
SAE 75W-90
Clutch
Clutch free play
Fluid type
Transfer (4WD models)
Oil capacity
Oil type
Recommended oil viscosity
0.2
0.6 in. (5 15 mm)
FMVSS No. 116 DOT 3 or SAE J1703
1.1 qt. (1.0 L, 0.9 Imp.qt.)
Gear oil API GL-5
SAE 75W-90
530
6-1. Specifications
Brakes
Pedal clearance
* 1
2WD models except
PreRunner
PreRunner
4WD models
Pedal free play
Brake pad wear limit
Brake lining wear limit
Parking brake pedal travel
* 2
(pedal type)
Parking brake lever travel
* 3
(lever type)
Fluid type
4.5 in. (115 mm)
4.4 in. (111 mm)
Without off-road package
4.4 in. (111 mm)
With off-road package
3.6 in. (91 mm)
0.04
0.24 in. (1 6 mm)
0.04 in. (1.0 mm)
0.04 in. (1.0 mm)
7 — 10 clicks
7 — 10 clicks
FMVSS No. 116 DOT 3 or SAE J1703
* 1
: Minimum pedal clearance when depressed with a force of 110 lbf (490 N,
50 kgf) with the engine running.
* 2
: Parking brake pedal travel when depressed with a force of 67.4 lbf (300 N,
30.6 kgf).
* 3
: Parking brake lever travel when pulled with a force of 44.9 lbf (200 N, 20.4
kgf).
6
Chassis lubrication (4WD models and PreRunner with 2.7L
4-cylinder [2TR-FE] engine only)
Propeller shafts Spider Lithium base chassis grease, NLGI No.2
531
6-1. Specifications
Steering
Free play
Power steering fluid type
Less than 1.2 in. (30 mm)
Automatic transmission fluid DEXRON
®
II or
III
Tires and wheels
Type A
Tire size
Tire inflation pressure
(Recommended cold tire inflation pressure)
Wheel size
Wheel nut torque
P215/70R15 97S
Front tires:
30 psi (210 kPa, 2.1 kgf/cm
2
or bar)
Rear tires:
33 psi (230 kPa, 2.3 kgf/cm
2
or bar)
Spare tire * :
33 psi (230 kPa, 2.3 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 3 psi (20 kPa, 0.2 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
15
6 J, 15 6 JJ
83 ft·lbf (113 N·m, 11.5 kgf·m)
* : If you affix the spare tire to a front position, please make sure to adjust the tire to the correct inflation pressure as soon as possible.
532
6-1. Specifications
Type B
Tire size
Tire inflation pressure
(Recommended cold tire inflation pressure)
Wheel size
Wheel nut torque
P245/75R16 109S
Front tires:
30 psi (210 kPa, 2.1 kgf/cm
2
or bar)
Rear tires:
30 psi (210 kPa, 2.1 kgf/cm
2
or bar)
Spare tire:
30 psi (210 kPa, 2.1 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 3 psi (20 kPa, 0.2 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
16
7 J, 16 7 JJ
83 ft·lbf (113 N·m, 11.5 kgf·m)
Type C
Tire size
Tire inflation pressure
(Recommended cold tire inflation pressure)
P265/70R16 111T
Front tires:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Rear tires:
32 psi (220 kPa, 2.2 kgf/cm
2
or bar)
Spare tire * :
32 psi (220 kPa, 2.2 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 3 psi (20 kPa, 0.2 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
16
7 JJ
Wheel size
Wheel nut torque 83 ft·lbf (113 N·m, 11.5 kgf·m)
*
: If you affix the spare tire to a front position, please make sure to adjust the tire to the correct inflation pressure as soon as possible.
533
6
6-1. Specifications
Type D
Tire size
Tire inflation pressure
(Recommended cold tire inflation pressure)
Wheel size
Wheel nut torque
Type E
Tire size
P265/65R17 110S
Front tires:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Rear tires:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Spare tire:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 3 psi (20 kPa, 0.2 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
17
7 1/2 JJ
83 ft·lbf (113 N·m, 11.5 kgf·m)
Tire inflation pressure
(Recommended cold tire inflation pressure)
Wheel size
Wheel nut torque
P255/45R18 99V
Front tires:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Rear tires:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Spare tire:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 4 psi (30 kPa, 0.3 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
18
8 JJ
83 ft·lbf (113 N·m, 11.5 kgf·m)
534
6-1. Specifications
Type F
Tire size
Tire inflation pressure
(Recommended cold tire inflation pressure)
Wheel size
Wheel nut torque
P265/60R18 109H
Front tires:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Rear tires:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Spare tire:
29 psi (200 kPa, 2.0 kgf/cm
2
or bar)
Driving at high speeds above 100 mph
(160 km/h) (in countries where such speeds are permitted by law)
Add 3 psi (20 kPa, 0.2 kgf/cm
2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.
18
7 1/2 J
83 ft·lbf (113 N·m, 11.5 kgf·m)
6
535
6-1. Specifications
Light bulbs
Exterior
Light Bulbs
Headlights
Front fog lights
* 1
Front side marker lights
Front turn signal lights/parking lights/ daytime running lights
Rear turn signal lights
Stop/tail and rear side marker lights
* 2
Back-up lights
Interior
License plate lights
High mounted stoplight
Interior light
Personal lights
* 1
: If equipped
* 2
: Bulb type only
A: HB2 halogen bulbs
B: H11 halogen bulbs
C: Wedge base bulbs (clear)
D: Wedge base bulbs (amber)
E: Double end bulbs
Bulb No.
—
—
—
4157
NAK
3157A
3157KX
921
168
168
—
168
W
60/55
55
5
27/8
27/8
27/8
18
5
5
5
5
D
D
C
C
C
C
E
C
Type
A
B
D
536
6-1. Specifications
Fuel information
Your vehicle must use only unleaded gasoline.
Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage.
At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A..
■ Fuel tank opening for unleaded gasoline
To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.
■
If your engine knocks
●
Consult your Toyota dealer.
●
You may occasionally notice light knocking for a short time while accelerating or driving uphill. This is normal and there is no need for concern.
■
Gasoline quality
In very few cases, driveability problems may be caused by the brand of gasoline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.
■
Gasoline quality standards
●
Automotive manufacturers in the US, Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.
●
The WWFC consists of four categories that are based on required emission levels. In the US, category 4 has been adopted.
●
The WWFC improves air quality by lowering emissions in vehicle fleets, and customer satisfaction through better performance.
6
537
6-1. Specifications
■ Toyota recommends the use of gasoline containing detergent additives
● Toyota recommends the use of gasoline that contains detergent additives to avoid build-up of engine deposits.
● All gasoline sold in the U.S. contains minimum detergent additives to clean and/or keep clean intake systems, per EPA’s lowest additives concentration program.
● Toyota strongly recommends the use of Top Tier Detergent Gasoline. For more information on Top Tier Detergent Gasoline and a list of marketers, please go to the official website www.toptiergas.com.
■ Toyota recommends the use of cleaner burning gasoline
Cleaner burning gasoline, including reformulated gasoline that contains oxygenates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas.
Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.
■ Toyota does not recommend blended gasoline
DO NOT use gasoline containing more than
15% ethanol.
(30% ethanol)
(50% ethanol)
(85% ethanol)
● Use only gasoline containing up to 15% ethanol.
DO NOT use any flex-fuel or gasoline that could contain more than 15% ethanol, including from any pump labeled
E30, E50, E85 (which are only some examples of fuel containing more than
15% ethanol).
● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87.
●
Toyota does not recommend the use of gasoline containing methanol.
538
6-1. Specifications
■ Toyota does not recommend gasoline containing MMT
Some gasoline contains octane enhancing additive called MMT
(Methylcyclopentadienyl Manganese Tricarbonyl).
Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected.
The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
NOTICE
■ Notice on fuel quality
● Do not use improper fuels.
If improper fuels are used the engine will be damaged.
● Do not use leaded gasoline.
Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
● Do not use gasohol other than that stated here.
Other gasohol may cause fuel system damage or vehicle performance problems.
● Using unleaded gasoline with an octane number or rating lower than the level previously stated will cause persistent heavy knocking.
At worst, this will lead to engine damage.
■ Fuel-related poor driveability
If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.
■ When refueling with gasohol
Take care not to spill gasohol.
It can damage your vehicle’s paint.
6
539
6-1. Specifications
Tire information
Typical tire symbols
540
Tire size
DOT and Tire Identification Number (TIN)
Location of treadwear indicators
Tire ply composition and materials
(
(
(
P. 542)
P. 541)
Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Uniform tire quality grading
For details, see “Uniform tire quality grading” that follows.
Load limit at maximum cold tire inflation pressure (
P. 545)
Maximum cold tire inflation pressure (
P. 545)
This means the pressure to which a tire may be inflated.
TUBELESS or TUBE TYPE
A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.
6-1. Specifications
Radial tires or bias-ply tires
A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire.
Summer tire or all season tire (
An all season tire has M+S on the sidewall. A tire not marked M+S is a summer tire.
Typical DOT and tire identification number (TIN)
DOT symbol *
Tire Identification Number
(TIN)
Tire manufacturer’s identification mark
Tire size code
Manufacturer’s optional tire type code (3 or 4 letters)
Manufacturing week
Manufacturing year
* : The DOT symbol certifies that the tire conforms to applicable Federal Motor
Vehicle Safety Standards.
6
541
6-1. Specifications
Tire size
■ Typical tire size information
The illustration indicates typical tire size.
Tire use
(P = Passenger car,
T = Temporary use)
Section width (millimeters)
Aspect ratio
(tire height to section width)
Tire construction code
(R = Radial, D = Diagonal)
Wheel diameter (inches)
Load index (2 digits or 3 digits)
Speed symbol
(alphabet with one letter)
■ Tire dimensions
Section width
Tire height
Wheel diameter
542
6-1. Specifications
Tire section names
Bead
Sidewall
Shoulder
Tread
Belt
Inner liner
Reinforcing rubber
Carcass
Rim lines
Bead wires
Chafer
Uniform Tire Quality Grading
This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the
U.S.A. Department of Transportation.
It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.
Your Toyota dealer will help answer any questions you may have as you read this information.
■
DOT quality grades
All passenger vehicle tires must conform to Federal Safety
Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
For example: Treadwear 200 Traction AA Temperature A
6
543
6-1. Specifications
■
Treadwear
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
■ Traction AA, A, B, C
The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
A tire marked C may have poor traction performance.
Warning: The traction grade assigned to this tire is based on braking
(straight ahead) traction tests and does not include cornering
(turning) traction.
■ Temperature A, B, C
The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle
Safety Standard No. 109.
Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.
544
6-1. Specifications
Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded.
Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
Glossary of tire terminology
Tire related term
Cold tire inflation pressure
Maximum inflation pressure
Recommended inflation pressure
Accessory weight
Curb weight
Maximum loaded vehicle weight
Meaning
Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition
The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire
Cold tire inflation pressure recommended by a manufacturer
The combined weight (in excess of those standard items which may be replaced) of transmission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory-installed equipment (whether installed or not)
The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine
The sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight
(d) Production options weight
6
545
6-1. Specifications
Tire related term
Normal occupant weight
Occupant distribution
Production options weight
Rim
Meaning
150 lb. (68 kg) times the number of occupants specified in the second column of Table 1 * that follows
Distribution of occupants in a vehicle as specified in the third column of Table 1 * below
The combined weight of installed regular production options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim
A metal support for a tire or a tire and tube assembly upon which the tire beads are seated
Rim diameter
(Wheel diameter)
Rim size designation
Rim type designation
Rim width
Vehicle capacity weight (Total load capacity)
Vehicle maximum load on the tire
Vehicle normal load on the tire
Nominal diameter of the bead seat
Rim diameter and width
The industry manufacturer's designation for a rim by style or code
Nominal distance between rim flanges
The rated cargo and luggage load plus 150 lb.
(68 kg) times the vehicle's designated seating capacity
The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two
The load on an individual tire that is determined by distributing to each axle its share of curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1 * below), and dividing by two
546
6-1. Specifications
Tire related term
Weather side
Bead
Bead separation
Bias ply tire
Carcass
Chunking
Cord
Cord separation
Cracking
CT
Extra load tire
Groove
Innerliner
Meaning
The surface area of the rim not covered by the inflated tire
The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim
A breakdown of the bond between components in the bead
A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the centerline of the tread
The tire structure, except tread and sidewall rubber which, when inflated, bears the load
The breaking away of pieces of the tread or sidewall
The strands forming the plies in the tire
The parting of cords from adjacent rubber compounds
Any parting within the tread, sidewall, or innerliner of the tire extending to cord material
A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire
A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire
The space between two adjacent tread ribs
The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire
547
6
6-1. Specifications
Tire related term
Innerliner separation
Intended outboard sidewall
Light truck (LT) tire
Load rating
Maximum load rating
Maximum permissible inflation pressure
Measuring rim
Open splice
Outer diameter
Overall width
Passenger car tire
Meaning
The parting of the innerliner from cord material in the carcass
(a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or
(b)The outward facing sidewall of asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle
A tire designated by its manufacturer as primarily intended for use on lightweight trucks or multipurpose passenger vehicles
The maximum load that a tire is rated to carry for a given inflation pressure
The load rating for a tire at the maximum permissible inflation pressure for that tire
The maximum cold inflation pressure to which a tire may be inflated
The rim on which a tire is fitted for physical dimension requirements
Any parting at any junction of tread, sidewall, or innerliner that extends to cord material
The overall diameter of an inflated new tire
The linear distance between the exteriors of the sidewalls of an inflated tire, including elevations due to labeling, decorations, or protective bands or ribs
A tire intended for use on passenger cars, multipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating
(GVWR) of 10,000 lb. or less
548
6-1. Specifications
Ply
Tire related term
Ply separation
Pneumatic tire
Radial ply tire
Reinforced tire
Section width
Sidewall
Sidewall separation
Snow tire
Test rim
Meaning
A layer of rubber-coated parallel cords
A parting of rubber compound between adjacent plies
A mechanical device made of rubber, chemicals, fabric and steel or other materials, that, when mounted on an automotive wheel, provides the traction and contains the gas or fluid that sustains the load
A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread
A tire designed to operate at higher loads and at higher inflation pressures than the corresponding standard tire
The linear distance between the exteriors of the sidewalls of an inflated tire, excluding elevations due to labeling, decoration, or protective bands
That portion of a tire between the tread and bead
The parting of the rubber compound from the cord material in the sidewall
A tire that attains a traction index equal to or greater than 110, compared to the ASTM E-
1136 Standard Reference Test Tire, when using the snow traction test as described in
ASTM F-1805-00, Standard Test Method for
Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( ) on at least one sidewall
The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire
549
6
6-1. Specifications
Tire related term
Tread
Tread rib
Tread separation
Treadwear indicators(TWI)
Meaning
That portion of a tire that comes into contact with the road
A tread section running circumferentially around a tire
Pulling away of the tread from the tire carcass
The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread
Wheel-holding fixture
The fixture used to hold the wheel and tire assembly securely during testing
*
: Table 1
Occupant loading and distribution for vehicle normal load for various designated seating capacities
Designated seating capacity, Number of occupants
2 through 4
5 through 10
11 through 15
16 through 20
Vehicle normal load,
Number of occupants
2
3
5
7
Occupant distribution in a normally loaded vehicle
2 in front
2 in front, 1 in second seat
2 in front, 1 in second seat, 1 in third seat, 1 in fourth seat
2 in front, 2 in second seat, 2 in third seat, 1 in fourth seat
550
6-2. Customization
Customizable features
Your vehicle includes a variety of electronic features that can be personalized to your preferences. Programming these preferences requires specialized equipment and may be performed by an authorized Toyota dealership.
Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details.
Customizable features
Item
Wireless remote control
(
Seat Belt
Reminder
Buzzer
(
Function
Operation signal
(Buzzer)
Vehicle speed linked seat belt reminder buzzer
Default setting
Customized setting
ON
ON
OFF
OFF
6
551
6-2. Customization
Items to initialize
The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle.
Item
Maintenance required reminder light
Tire pressure warning system
When to initialize
After the maintenance is performed
• When rotating the tires on vehicles differing with front and rear tire inflation pressures.
• When changing the tire inflation pressure by changing traveling speed or load weight, etc.
• When changing the tire size.
Reference
552
For owners
7
Reporting safety defects for U.S. owners .............. 554
Seat belt instructions for Canadian owners
(in French) ..................... 555
SRS airbag instructions for Canadian owners
(in French) ..................... 557
Camper information ......... 567
553
Reporting safety defects for U.S. owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free:
1-800-331-4331).
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safer-
car.gov; or write to: Administrator, NHTSA, 1200 New Jersey Ave,
S.E., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
554
Seat belt instructions for Canadian owners (in French)
The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual.
See the seat belt section for more detailed seat belt instructions in
English.
555
7
556
SRS airbag instructions for Canadian owners (in French)
The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual.
See the SRS airbag section for more detailed SRS airbag instructions in English.
557
7
558
559
7
560
561
7
562
563
7
564
590
565
7
566
Camper information
This information has been prepared in accordance with regulation issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on truck-camper loading. Your Toyota dealer will help answer any questions you may have as you read this information.
Center of gravity location
The figures given in the illustration indicate the recommended center of gravity zone.
Recommended location for cargo center of gravity for cargo weight rating
Rear end of truck bed
Access Cab models
Except X-Runner
X-Runner *
Double Cab models
With short deck
With long deck
49.9 in. (1267 mm)
—
45.6 in. (1157 mm)
35.9 in. (911 mm)
36.1 in. (917 mm)
—
31.8 in. (807 mm)
27.8 in. (706 mm)
* :Truck-campers cannot be used with the X-Runner since it is not designed for them.
7
567
CAUTION
■ Loading precaution
If a load is too far back, it can cause dangerous handling. If it is too far forward, the front axle may be overloaded.
Cargo weight rating and proper matching
When the truck is used to carry a slide-in camper, the total cargo load of the truck consists of the manufacturer’s camper weight figure, the weight of installed additional camper equipment not included in the manufacturer’s camper weight figure, the weight of camper cargo, and the weight of passengers in the camper.
The total cargo load should not exceed the truck’s cargo weight rating and the camper’s center of gravity should fall within the truck’s recommended center of gravity zone when installed.
Camper center of gravity
Recommended center of gravity location zone
568
■
Cargo weight rating
Access Cab models
2 people, 2TR-FE engine, 2WD except PreRunner:
750 lb. (340 kg)
4 people, 2TR-FE engine, 2WD except PreRunner:
450 lb. (204 kg)
2 people, 2TR-FE engine, PreRunner:
4 people, 2TR-FE engine, PreRunner:
2 people, 1GR-FE engine, PreRunner:
4 people, 1GR-FE engine, PreRunner:
1000 lb. (453 kg)
700 lb. (317 kg)
950 lb. (430 kg)
650 lb. (294 kg)
2 people, 2TR-FE engine, 4WD:
4 people, 2TR-FE engine, 4WD:
2 people, 1GR-FE engine, 4WD:
4 people, 1GR-FE engine, 4WD:
900 lb. (408 kg)
600 lb. (272 kg)
840 lb. (381 kg)
540 lb. (244 kg)
Double Cab models with short deck
2 people, 2TR-FE engine, 2WD except PreRunner:
650 lb. (294 kg)
5 people, 2TR-FE engine, 2WD except PreRunner:
200 lb. (90 kg)
2 people, 1GR-FE engine, PreRunner:
5 people, 1GR-FE engine, PreRunner:
2 people, 1GR-FE engine, 4WD:
5 people, 1GR-FE engine, 4WD:
850 lb. (385 kg)
400 lb. (181 kg)
740 lb. (335 kg)
290 lb. (131 kg)
Double Cab models with long deck
2 people, 1GR-FE engine, PreRunner:
5 people, 1GR-FE engine, PreRunner:
2 people, 1GR-FE engine, 4WD:
5 people, 1GR-FE engine, 4WD:
850 lb. (385 kg)
400 lb. (181 kg)
740 lb. (335 kg)
290 lb. (131 kg)
7
569
CAUTION
■ Overloading
Be careful — overloading can cause dangerous braking and handling problems, and can damage your vehicle and its tires.
Gross axle and vehicle weight ratings
Secure loose items to prevent weight shifts that could affect the balance of your vehicle. When the truck camper is loaded, drive to a scale and weigh on the front and on the rear wheels separately to determine axle loads. Individual axle loads should not exceed either of the Gross Axle Weight Ratings (GAWR). The total of the axle loads should not exceed the Gross Vehicle Weight Rating (GVWR). These ratings are given on the vehicle certification label which is located on the door latch post on the left side of the vehicle. (
ratings are exceeded, move or remove items to bring all weights below the ratings.
570
Gross axle weight rating
Front GAWR
Rear GAWR
Gross vehicle weight rating
Not exceed GVWR
■
GAWR
2WD models except PreRunner
4WD models and
PreRunner
GAWR
Front
Vehicles with 2.7L
4-cylinder (2TR-FE) engine
2380 lb. (1075 kg)
Vehicles with 4.0 L
V6 (1GR-FE) engine
2400 lb. (1085 kg)
PreRunner
2755 lb. (1245 kg)
4WD models
2775 lb. (1255 kg)
Rear
2650 lb. (1200 kg)
3110 lb. (1410 kg)
7
571
■
GVWR
2WD models except PreRunner
Cab type
Access Cab
Double Cab
GVWR
Vehicles with 2.7 L 4-cylinder (2TR-FE) engine
4900 lb. (2220 kg)
Vehicles with 4.0 L V6 (1GR-FE) engine
4700 lb. (2130 kg)
4900 lb. (2220 kg)
PreRunner
Cab type
Access Cab and
Double Cab
GVWR
Vehicles with 2.7 L 4-cylinder (2TR-FE) engine
5250 lb. (2380 kg)
Vehicles with 4.0 L V6 (1GR-FE) engine
5400 lb. (2445 kg)
4WD models
Cab type
Access Cab
Double Cab
GVWR
Vehicles with 2.7 L 4-cylinder (2TR-FE) engine
5350 lb. (2425 kg)
Vehicles with 4.0 L V6 (1GR-FE) engine
5500 lb. (2490 kg)
5500 lb. (2490 kg)
572
Index
Abbreviation list ..................... 574
Alphabetical index.................. 576
What to do if... ........................ 585
For vehicles with Entune Audio Plus or Entune Premium
Audio, refer to the “NAVIGATION SYSTEM OWNER’S
MANUAL” for information regarding the multimedia system.
Multimedia system types:
573
Abbreviation list
Abbreviation/Acronym list
ABBREVIATIONS
2WD
4WD
ABS
ACC
ALR
A-TRAC
AUTO LSD
CRS
DAC
ECU
EDR
ELR
GAWR
GCWR
GVWR
I/M
LATCH
LED
LT
M + S
MMT
MTBE
OBD
RR DIFF LOCK
RSCA
SRS
TIN
574
MEANING
Two Wheel Drive
Four Wheel Drive
Anti-Lock Brake System
Accessory
Automatic Locking Retractor
Active Traction Control
Automatic Limited Slip Differential
Child Restraint System
Downhill assist control
Electronic Control Unit
Event Data Recorder
Emergency Locking Retractor
Gross Axle Weight Rating
Gross Combination Weight Rating
Gross Vehicle Weight Rating
Emission inspection and maintenance
Lower Anchors and Tethers for Children
Light Emitting Diode
Light truck
Mud + Snow
Methylcy clopentadienyl Manganese Tricarbonyl
Methyl Tertiary Butyl Ether
On Board Diagnostics
Rear differential lock
Roll sensing of curtain shield airbag
Supplemental Restraint System
Tire Identification Number
ABBREVIATIONS
TPMS
TRAC
TWI
TWR
VIN
VSC
MEANING
Tire Pressure Warning System
Traction Control
Treadwear indicators
Trailer Weight Rating
Vehicle Identification Number
Vehicle Stability Control
Abbreviation list
575
Alphabetical index
Alphabetical index
A
A/C.............................................236
AAC disc ...................................263
ABS ...........................................191
Access doors .............................39
Active traction control
system ....................................181
Air conditioning filter...............439
Air conditioning system
Air conditioning filter..............439
Manual air conditioning
system ................................236
Airbags
Airbag operating conditions.....85
Airbag precautions for your
child ......................................89
Airbag warning light...............477
Curtain shield airbag
operating conditions..............85
Curtain shield airbag
precautions ...........................89
Front passenger occupant
classification system .............95
General airbag precautions.....89
Locations of airbags ................82
Modification and disposal
of airbags ..............................93
Proper driving posture.......80, 89
Roll sensing of curtain shield
airbag off switch....................94
Side airbag operating
conditions..............................85
Side airbag precautions ..........89
SRS airbags ............................82
Antenna.....................335, 388, 390
Anti-lock brake system
ABS warning light..................477
Anti-lock brake system ..........191
Audio input ...............................249
Audio system
Antenna................. 335, 388, 390
Audio input ............................ 249
AUX port ............................... 249
CD player .............................. 263
iPod....................................... 270
MP3/WMA/AAC disc ............. 263
Portable music
player.................................. 249
Steering wheel audio switch
*
Sub woofer............................ 334
Type ...................................... 243
USB memory......................... 276
AUTO LSD system ................... 183
Automatic light off system...... 154
Automatic limited slip
differential .............................. 183
Automatic transmission
Automatic transmission......... 134
If the shift lever cannot be
shifted from P ..................... 502
AUX port ................................... 249
Auxiliary box .... 340, 345, 364, 365
B
Back-up lights
Replacing light bulbs............. 460
Wattage................................. 536
Back window .............................. 73
Battery
Charging system warning
light ..................................... 477
Checking ............................... 418
If the vehicle battery is
discharged .......................... 504
Preparing and checking
before winter....................... 209
Bluetooth
®
audio ..................... 304
Bluetooth
®
phone .................... 305
Bottle holders................... 340, 344
Brake assist.............................. 191
576
Alphabetical index
Brakes
Brake system warning buzzer
........... 182, 184, 189, 195, 476
Brake system warning
light .................................... 476
Fluid...................................... 414
Parking brake ....................... 142
Break-in tips ............................ 122
C
Camper information ................ 567
Care
Exterior ................................. 388
Interior .................................. 391
Seat belts ............................. 392
Cargo capacity ................ 202, 518
Cargo net hook................ 364, 372
CD player ................................. 263
Certification label ............ 217, 521
Chains ...................................... 210
Child restraint system
Booster seats, definition ....... 100
Booster seats, installation .... 113
Convertible seats,
definition............................. 100
Convertible seats,
installation .......................... 110
Front passenger occupant
classification system ............ 95
Infant seat, definition ............ 100
Infant seats, installation........ 110
Installing CRS with LATCH
system........................ 107, 109
Installing CRS with seat
belts ................................... 110
Installing CRS with top
tether straps ............... 114, 115
Child safety
Airbag precautions ..................89
Battery precautions .......419, 507
Child restraint system............100
Child-protectors.......................37
How your child should wear
the seat belt ..........................59
Installing child restraints........104
Power window lock switch.......71
Power window precautions .....72
Removed wireless remote control battery
precautions .........................443
Seat belt extender
precautions ...........................62
Seat belt precautions ..............60
Seat heater precautions ........360
Child-protectors .........................37
Cleaning
Exterior..................................388
Interior ...................................391
Seat belts ..............................392
Clock ........................................ 351
Clutch start cancel switch.......190
Compass...................................381
Condenser ................................414
Console box .....................340, 341
Cooling system
Engine overheating ...............508
CRS ...........................................100
Cruise control...........................162
Cup holders ......................340, 342
Curtain shield airbags ...............82
Customizable features.............551
*
: Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.
577
Alphabetical index
D
Daytime running light
system ....................................154
Deck
Auxiliary boxes ......................365
Deck ......................................364
Deck hooks ...........................366
Deck rails ..............................202
Tie-down cleats .....................367
Detachable pole antenna.........335
Dimension.................................516
Dinghy towing ..........................233
Do-it-yourself maintenance.....400
Doors
Access doors...........................39
Door glasses ...........................71
Door lock ...........................32, 35
Open door warning light ........479
Side doors ...............................35
Side mirrors.............................68
Downhill Assist Control
System....................................188
Driver’s seat belt reminder
light .........................................479
Driver’s seat belt reminder
warning buzzer ......................479
Driving
Break-in tips ..........................122
Correct posture .......................80
Driving assist systems...........191
Procedures............................120
Winter driving tips..................209
E
Emergency, in case of
Blown fuse.............................444
If the engine will not start ......501
If the shift lever cannot be
shifted from P......................502
If the vehicle battery is
discharged ..........................504
If the warning buzzer
sounds ................................476
If the warning light turns on ...476
578
If you have a flat tire ............. 486
If you lose your keys ............. 503
If you think something is
wrong.................................. 474
If the vehicle becomes
stuck ................................... 511
If your vehicle has to be
stopped in an emergency ... 513
If your vehicle needs to be
towed .................................. 467
If your vehicle overheats ....... 508
Emergency flashers
Switch ................................... 466
Engine
Compartment ........................ 406
Engine switch........................ 131
Exhaust gas .......................... 127
Hood ..................................... 404
How to start the engine ......... 131
Identification number............. 521
If the engine will not start ...... 501
Ignition switch ....................... 131
Immobilizer system ................. 77
Overheating .......................... 508
Warning light ......................... 477
Engine coolant
Capacity ................................ 527
Checking ............................... 412
Preparing and checking
before winter....................... 209
Temperature gauge .............. 145
Engine coolant temperature
gauge...................................... 145
Engine immobilizer system ...... 77
Engine oil
Capacity ................................ 524
Checking ............................... 408
Preparing and checking
before winter....................... 209
Warning light ......................... 477
Engine switch........................... 131
Event data recorder ................... 24
Alphabetical index
F
Floor mat.................................. 362
Fluid
Brake .................................... 414
Washer ................................. 420
Fog lights
Replacing light bulbs ............ 457
Switch................................... 155
Wattage ................................ 536
Four-wheel drive system
Front-wheel drive control
switch ................................. 177
Front fog lights
Replacing light bulbs ............ 457
Switch................................... 155
Wattage ................................ 536
Front passenger occupant
classification system.............. 95
Front passenger’s seat belt
reminder light........................ 479
Front passenger’s seat belt
warning buzzer...................... 479
Front seats
Adjustment ............................. 45
Front side marker lights
Replacing light bulbs ............ 458
Switch................................... 152
Wattage ................................ 536
Front turn signal lights
Lever .................................... 141
Replacing light bulbs ............ 459
Switch................................... 141
Wattage ................................ 536
Fuel
Capacity ............................... 523
Fuel gauge ........................... 145
Fuel pump shut off system ... 475
Gas station information ........ 588
Information ........................... 537
Refueling ................................ 74
Type ..................................... 523
Warning light ........................ 479
Fuel door.................................... 74
Fuel filler door ........................... 74
Fuel pump shut off system .....475
Fuses
Fuses ....................................444
Locations.......................447, 451
G
Garage door opener.................373
Gas station information...........588
Gauges......................................145
Glove box..................................341
Grocery bag hooks ..................371
H Hands-free system
(for cellular phone) ................305
Hazard lights
Switch....................................466
Head restraints
Adjusting ................................53
Headlights
Replacing light bulbs .............455
Switch....................................152
Wattage.................................536
Heaters
Seat heaters..........................359
High mounted stoplight
Replacing ..............................461
Wattage.................................536
Hill-start assist control ............191
Hood..........................................404
Hooks
Cargo net ..............................372
Deck hooks ...........................366
Grocery bag ..........................371
Tie-down cleats .....................367
Horn...........................................144
I
I/M test.......................................399
Identification
Engine ...................................522
Tire ........................................541
Vehicle ..................................521
Ignition switch..........................131
Illuminated entry system.........338
579
Alphabetical index
Immobilizer system....................77
Indicator lights .........................148
Initialization
Items to initialize....................552
Inside rear view mirror ..............64
Interior lights
Interior lights..........................339
Personal lights.......................339
Switch....................................339
Wattage.................................536
Instrument panel light
control ....................................146
J
Jack
Positioning the jack ...............491
Vehicle-equipped jack ...........486
Jack handle ..............................490
K
Keyless entry..............................32
Keys
Engine switch ........................131
If you lose your keys .............503
Ignition switch........................131
Keyless entry...........................32
Key number.............................30
Keys ........................................30
Reminder buzzer...................482
Wireless remote control ..........32
Wireless remote control
battery.................................442
L
License plate lights
Replacing light bulbs .............462
Switch....................................152
Wattage.................................536
Light bulbs
Replacing ..............................454
Wattage.................................536
Lights
Automatic light off system .....154
Emergency flashers switch ...466
Fog light switch .....................155
580
Hazard light switch................ 466
Headlights switch .................. 152
Instrument panel light
control dial .......................... 146
Interior light switch ................ 339
Replacing light bulbs............. 454
Turn signal lights switch........ 141
Wattage................................. 536
Limited slip differential ........... 183
Load capacity........... 202, 207, 518
Lock steering column................ 63
Luggage storage box .............. 369
Luggage compartment
features .................................. 364
M
Maintenance
Do-it-yourself
maintenance ....................... 400
General maintenance............ 396
Maintenance data ................. 516
Maintenance requirements ... 394
Reset the maintenance
data..................................... 395
Vehicle exterior ..................... 388
Vehicle interior ...................... 391
Malfunction indicator lamp ..... 477
Manual air conditioning
system .................................... 236
Manual transmission ............... 138
Meter
Instrument panel light
control................................. 146
Meters ................................... 145
Mirrors
Inside rear view mirror ............ 64
Side mirrors............................. 68
Vanity mirrors........................ 350
MP3 disc ................................... 263
N
Noise from under vehicle.......... 22
O
Odometer.................................. 146
Alphabetical index
Off-road precautions
Driving .................................. 199
Vehicle.................................. 197
Oil
Engine oil.............................. 408
Warning light ................ 477, 479
Opener
Fuel door ................................ 74
Hood..................................... 404
Outside rear view mirrors
Adjusting and folding .............. 68
Overhead console ................... 348
Overheating, Engine ............... 508
P
Parking brake .......................... 142
Personal lights ........................ 339
Parking lights
Replacing light bulbs ............ 459
Switch................................... 152
Wattage ................................ 536
Pole antenna............................ 335
Power outlet..................... 352, 353
Power steering
Fluid...................................... 416
Power windows ......................... 71
R
Radiator............................ 406, 414
Radio ........................................ 261
Rear seat
Adjustment ............................. 49
Folding down .......................... 50
Raising the bottom
cushion................................. 49
Rear side marker lights
Replacing light bulbs .... 460, 464
Switch................................... 152
Wattage ................................ 536
Rear turn signal lights
Lever .................................... 141
Replacing light bulbs ............ 460
Switch................................... 141
Wattage ................................ 536
Rear view monitor system
Before removing the
tailgate ..................................40
Rear view monitor
system ................................166
Rear window...............................73
Replacing
Fuses ....................................444
Light bulbs.............................454
Tires ..............................422, 486
Wheels ..................................436
Wireless remote control
battery.................................442
Rear differential lock
system ....................................185
Rear step bumper ......................43
Reporting safety defects for
U.S. owners ............................554
Resetting the maintenance
required reminder light .........395
Roll sensing of curtain shield
airbags off switch ....................94
S
Seat belts
Adjustment ..............................57
ALR .........................................59
Automatic Locking
Retractor ...............................59
Child restraint system
installation...........................104
Cleaning and maintaining......392
ELR .........................................59
Emergency Locking
Retractor ...............................59
How to wear your seat belt......57
How your child should wear
the seat belt ..........................59
Pregnant women, proper
seat belt use .........................59
Reminder buzzer...................479
Reminder light .......................479
Seat belt extenders .................60
Seat belt pretensioners ...........58
581
Alphabetical index
Seat heaters..............................359
Seating capacity.......................207
Seats
Adjustment ..............................45
Adjustment precautions...........48
Child seats/child restraint
system installation ..............104
Cleaning ............................... 391
Folding down the rear seat......50
Folding down the rear seat
precautions ...........................52
Folding passenger’s seat ........46
Front seat adjustment .............45
Front seat adjustment
precautions ...........................48
Head restraint..........................53
Moving passenger’s seat for
rear seat entry.......................46
Properly sitting in the seat.......80
Raising the bottom cushion.....49
Seat heaters..........................359
Seatback table..........................361
Service reminder
indicators ..............................148
Shift lever
Automatic transmission .........134
If the shift lever cannot be
shifted from P......................502
Manual transmission .............138
Shift lock system .....................502
Side airbags................................82
Side doors ..................................35
Side marker lights
Replacing light bulbs .....458, 464
Switch....................................152
Wattage.................................536
Side mirror
Adjusting and folding...............68
Spare tire
Inflation pressure .................. 532
Replacing .............................. 486
Storage location .................... 486
Spark plug ................................ 527
Specifications .......................... 516
Speedometer ............................ 145
SRS airbags
Curtain shield airbags ............. 82
Front airbags........................... 82
Precautions ............................. 89
Roll sensing of curtain shield
airbag off switch.................... 94
Side airbags ............................82
Steering wheel
Adjustment .............................. 63
Audio switches
*
Telephone switches
*
Stop lights
Replacing light bulbs..... 460, 463
Wattage................................. 536
Storage feature ........................ 340
Storage precautions ................ 205
Stuck
If the vehicle becomes
stuck ................................... 511
Sun visors ................................ 349
Switch
A-TRAC switch...................... 181
Clutch start cancel switch ..... 190
Cruise control switch............. 162
DAC switch ........................... 188
Emergency flashers switch ... 466
Engine switch........................ 131
Fog light switch ..................... 155
Front-wheel drive control
switch.................................. 177
Hazard light switch................ 466
Headlights switch .................. 152
582
Alphabetical index
Ignition switch....................... 131
Light switch........................... 152
Power door lock switch........... 36
Power window switch ............. 71
Rear differential lock
switch ................................. 185
Roll sensing of curtain shield
airbag off switch ................... 94
Tire pressure warning
reset switch ........................ 423
Turn signal lights .................. 141
VSC OFF switch........... 183, 192
Window lock switch ................ 71
Wiper and washer ................ 156
T
Tachometer.............................. 145
Tailgate
Removing the tailgate............. 40
Tailgate................................... 40
Tail lights
Replacing light bulbs .... 460, 464
Switch................................... 152
Wattage ................................ 536
Talk switch
*
Telephone switch
*
Theft deterrent system
Engine immobilizer system..... 77
Tire inflation pressure ............ 532
Tire information
Glossary ............................... 545
Size ...................................... 542
Tire identification number ..... 541
Uniform tire quality
grading ............................... 543
Tires
Chains ...................................210
Checking ...............................422
If you have a flat tire..............486
Identification number.............541
Inflation pressure...................532
Inflation pressure sensor.......423
Information ............................540
Replacing ..............................486
Rotating tires .........................422
Size .......................................532
Snow tires .............................426
Spare tire...............................486
Tire pressure warning
reset switch.........................423
Tire pressure warning
system ........................422, 483
Warning light .........................479
Tools .........................................486
Total load capacity...................207
Towing
Bumper towing ......................222
Dinghy towing........................233
Emergency towing.................467
Fifth wheel trailer...................220
Trailer towing.........................213
Traction control system ..........191
TRAC .........................................191
Trip meter .................................146
Turn signal lights
Lever .....................................141
Replacing light
bulbs ...........................459, 460
Switch....................................141
Wattage.................................536
*
: Refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.
583
Alphabetical index
V
Vanity mirrors...........................350
Vehicle control and
operation data recording ........23
Vehicle data recordings ............23
Vehicle identification
number ...................................521
Vehicle stability control...........191
VSC............................................191
W
Warning buzzers
Key reminder.........................482
Brake system ........................476
Seat belt reminder.................479
Warning lights
ABS .......................................477
Airbag system .......................477
Anti-lock brake system ..........477
Automatic transmission
fluid temperature.................479
Brake system ........................476
Charging system ...................477
Driver’s seat belt ...................479
Electronic engine control
system ................................477
Engine oil replacement..........479
Front passenger occupant
classification system ...........477
Front passenger’s seat
belt ......................................479
Low brake fluid ......................476
Low engine oil pressure ........477
Low fuel level ........................479
Low tire inflation pressure .....479
Malfunction indicator lamp ....477
Open door .............................479
Seat belt ................................479
Seat belt pretensioner
system ................................477
SRS.......................................477
SRS airbag system ...............477
Tire pressure......................... 479
Tire pressure warning
system ................................ 479
VSC/TRAC............................ 477
Washer
Checking ............................... 420
Preparing and checking
before winter....................... 209
Switch ................................... 156
Washing and waxing ............... 388
Weight
Cargo capacity ...................... 202
Cargo weight rating............... 568
Gross axle weight rating ....... 570
Gross combination weight
rating................................... 218
Gross vehicle weight
rating................................... 570
Load limits............................. 207
Trailer weight rating ...... 218, 519
Vehicle capacity weight......... 518
Weight................................... 518
Wheels ...................................... 436
Window glasses ................. 71, 73
Window lock switch................... 71
Windows
Power windows ....................... 71
Washer.................................. 156
Windshield wipers ................... 156
Wireless remote control
Replacing the battery ............ 442
Wireless remote control .......... 32
Winter driving tips ................... 209
WMA disc.................................. 263
584
What to do if...
What to do if...
A tire punctures
If you have a flat tire
The engine does not start
The shift lever cannot be moved out
The engine coolant temperature gauge enters the red zone
If the engine will not start
Engine immobilizer system
If the vehicle battery is discharged
If the shift lever cannot be shifted from P
If your vehicle overheats
Steam can be seen coming from under the hood
The key is lost
If you lose your keys
The battery runs out
If the vehicle battery is discharged
The doors cannot be locked
Side doors
Access doors
If the vehicle becomes stuck
The vehicle is stuck in mud or sand
The warning light or indicator light comes on
If a warning light turns on
585
What to do if...
■
Instrument cluster
■
Center panel
586
What to do if...
■Warning lights
Brake system warning light
Slip indicator
* 1
or or
Charging system warning light
Low engine oil pressure warning light
Malfunction indicator lamp
Cruise control indicator light
* 2
Open door warning light
Driver’s seat belt reminder light
Front passenger’s seat belt reminder light
Automatic transmission fluid temperature warning light
SRS warning light
Tire pressure warning light
ABS warning light Low fuel level warning light
or
Maintenance required reminder light
*
*
1
: Slip indicator comes on.
2
: The indicator flashes to indicate a malfunction.
587
588
GAS STATION INFORMATION
Auxiliary catch lever
Fuel filler door
Hood lock release lever
Tire inflation pressure
Fuel tank capacity
(Reference)
Fuel type
Cold tire inflation pressure
Engine oil capacity
(Drain and refill
-reference)
Engine oil type
21.1 gal. (80.0 L, 17.6 Imp.gal.)
Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher
ડાઉનલોડ કરો
જાહેર લિંક અપડેટ થઈ
તમારી ચેટની જાહેર લિંક અપડેટ કરવામાં આવી છે. You may view and manage your chat links after registration here.
દસ્તાવેજ જાહેર લિંક
જાહેરાત