3-2. Using the multimedia system
When using the Bluetooth
®
message function
Symptom Likely cause
Messages cannot be viewed.
New message notifications are not displayed.
Message transfer is not enabled on the cellular phone.
Automatic transfer function on this system is set to off.
Notification of SMS/
MMS/E-mail reception on this system is set to off.
Solution
Enable message transfer on the cellular phone
(approve message transfer on the phone).
Set automatic transfer function on this system to on. (
P. 329)
Set notification of SMS/
MMS/E-mail reception on this system to on.
(
P. 329)
Automatic message transfer function is not enabled on the cellular phone.
Enable automatic transfer function on the cellular phone.
3
295
3-2. Using the multimedia system
In other situations
Symptom Likely cause
The cellular phone is not close enough to this system.
Solution
Bring the cellular phone closer to this system.
Even though all conceivable measures have been taken, the symptom status does not change.
The cellular phone is the most likely cause of the symptom.
• Turn the cellular phone off, remove and reinstall the battery pack, and then restart the cellular phone.
• Enable the cellular phone’s Bluetooth
®
connection.
• Stop the cellular phone’s security software and close all applications.
• Before using an application installed on the cellular phone, carefully check its source and how its operation might affect this system.
296
3-2. Using the multimedia system
Bluetooth
®
■ About Bluetooth
®
The Bluetooth
®
word mark and logos are registered trademarks owned Bluetooth
SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Other trademarks and trade names are those of their respective owners.
■ When using the Bluetooth
®
audio system
● In the following conditions, the system may not function.
• If the portable audio player is turned off
• If the portable audio player is not connected
• If the portable audio player’s battery is low
● There may be a delay if a cellular phone connection is made during
Bluetooth
®
audio play.
● Depending on the type of portable audio player that is connected to the system, operation may differ slightly and certain functions may not be available.
■ When using the hands-free system
● The multimedia system is muted when making a call.
● If both parties speak at the same time, it may be difficult to hear.
● If the received call volume is overly loud, an echo may be heard.
If the Bluetooth
®
phone is too close to the system, quality of the sound may deteriorate and connection status may deteriorate.
● In the following circumstances, it may be difficult to hear the other party:
• When driving on unpaved roads
• When driving at high speeds
• If a window is open
• If the air conditioning is blowing directly on the microphone
• If there is interference from the network of the cellular phone
3
297
3-2. Using the multimedia system
■ Conditions under which the system will not operate
● If using a cellular phone that does not support Bluetooth
®
● If the cellular phone is turned off
● If you are outside of cellular phone service coverage
● If the cellular phone is not connected
● If the cellular phone’s battery is low
● When outgoing calls are controlled, due to heavy traffic on telephone lines, etc.
● When the cellular phone itself cannot be used
● When transferring contact data from the cellular phone
■ Bluetooth
®
antenna
The antenna is built into the display.
If the portable audio player is behind the seat or in the glove box or console box, or is touching or covered by metal objects, the connection status may deteriorate.
If the cellular phone is behind the seat or in the console box, or touching or covered by metal objects, the connection status may deteriorate.
■ Battery charge/signal status
● This display may not correspond exactly with the portable audio player or cellular phone itself.
● This system does not have a charging function.
● The portable audio player or cellular phone battery will be depleted quickly when the device is connected to Bluetooth
®
.
■ When using the Bluetooth
®
audio and hands-free system at the same time
The following problems may occur.
● The Bluetooth
®
audio connection may be interrupted.
● Noise may be heard during Bluetooth
®
audio playback.
298
3-2. Using the multimedia system
■ About the contact in this system
The following data is stored for every registered cellular phone. When another phone is connecting, you cannot read the registered data.
● Contact data
● Call history
● Favorite
● Message
When removing a Bluetooth
®
phone from the system, the above-mentioned data is also deleted.
■ Compatible models
The Bluetooth
®
audio system supports portable audio players with the following specifications
● Bluetooth
®
specifications:
Ver. 2.0, or higher (Recommended: Ver. 3.0+EDR or higher)
● Profiles:
• A2DP (Advanced Audio Distribution Profile) Ver. 1.0, or higher
(Recommended: Ver. 1.2 or higher)
This is a profile to transmit stereo audio or high quality sound to the multimedia system.
• AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher
(Recommended: Ver. 1.4 or higher)
This is a profile to allow remote control the A/V equipment.
However, please note that some functions may be limited depending on the type of portable audio player connected.
The hands-free system supports cellular phones with the following specifications.
• Bluetooth
®
specification:
Ver. 2.0 or higher (Recommended: Ver. 3.0+EDR or higher)
3
299
3-2. Using the multimedia system
● Profiles:
• HFP (Hands Free Profile) Ver. 1.0 or higher (Recommended: Ver. 1.6
or higher)
This is a profile to allow hands-free phone calls using a cellular phone or head set. It has outgoing and incoming call functions.
• OPP (Object Push Profile) Ver. 1.1 or higher (Recommended: Ver. 1.2)
This is a profile to transfer contact data. When a Bluetooth
®
compatible cellular phone has both PBAP and OPP, OPP cannot be used.
• PBAP (Phone Book Access Profile) Ver. 1.0 or higher (Recommended:
Ver. 1.1)
This is a profile to transfer contact data.
If the cellular phone does not support HFP, you cannot register it with the hands-free system. OPP, PBAP services must be selected individually.
■ Certifications for the Bluetooth
®
For vehicles sold in U.S.A.
FCC ID: ACJ932YEAP01A446
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For vehicles sold in Canada
IC: 216J-YEAP01A446
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
300
3-2. Using the multimedia system
The latest original “DECLARATION of CONFORMITY” (DoC) is available at the address stated.
http://www.ptc.panasonic.de/
3
301
3-2. Using the multimedia system
■ Reconnecting the portable audio player
If the portable audio player is disconnected due to poor reception when the engine switch is in the “ACC” or “ON” position, the system automatically reconnects the portable audio player.
If you have switched off the portable audio player yourself, follow the instructions below to reconnect:
● Select the portable audio player again
● Enter the portable audio player
■ When you sell your car
Be sure to delete your personal data. (
P. 252)
CAUTION
■ FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radio frequency radiation exposure information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of
7.9 in. (20 cm) between the radiator and your body.
This transmitter must not be co-located operating in conjuction with any other antenna or transmitter.
■ While driving
Do not use the portable audio player, cellular phone or connect a device to the Bluetooth
®
system.
302
3-2. Using the multimedia system
CAUTION
■ Caution regarding interference with electronic devices
● Your audio unit is fitted with Bluetooth
®
antennas. People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should maintain a reasonable distance between themselves and the Bluetooth
®
antennas. The radio waves may affect the operation of such devices.
● Before using Bluetooth
®
devices, users of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
3
NOTICE
■ When leaving the vehicle
Do not leave your portable audio player or cellular phone in the vehicle. The inside of the vehicle may become hot, causing damage to the portable audio player or cellular phone.
303
3-2. Using the multimedia system
Listening to Bluetooth
®
audio
The Bluetooth
®
audio system enables the user to enjoy music played on a portable player from the vehicle speakers via wireless communication.
Select “ Audio” on the “Select Audio Source” screen.
When a Bluetooth
®
device cannot be connected, check the connection status on the “Bluetooth Audio” screen. If the device is not connected, either register or reconnect the device. (
P. 288)
Audio control screen
Some titles and controls may not be displayed depending on the type of portable audio player used.
Connection status
Battery charge
“Select Audio Source” screen appears
Selecting a Bluetooth
®
device
Select to display the play mode selection screen
Random playback
Repeat play
Pause
Select to resume play
Setting the sound (
P. 260)
Indicators Conditions
Not connected
Connection status
Good
Full Empty
Battery charge
304
3-2. Using the multimedia system
Using a Bluetooth
®
phone
The hands-free system is a function that allows you to use your cellular phone without touching it.
This system supports Bluetooth
®
. Bluetooth
®
is a wireless data system that allows the cellular phone to wirelessly connect to the hands-free system and make/receive calls.
Before making a phone call, check the connection status, battery charge, call area and signal strength. (
P. 306)
If a Bluetooth
®
device cannot be connected, check the connection status on the phone screen. If the device is not connected, either register or reconnect it. (
P. 288)
Phone screen
To display the screen shown below, press the switch on the steering wheel or press the button.
Several functions are available to operate on each screen that is displayed by selecting the 4 tabs.
Device name
Bluetooth
®
connection status
3
305
3-2. Using the multimedia system
■
Microphone
The vehicle’s built in microphone is used when talking on the phone.
The person you are speaking to can be heard from the front speakers.
To use the hands-free system, you must register your Bluetooth
® phone in the system. (
P. 286)
Status display
You can check indicators such as signal strength and battery charge on any screen.
Connection status
Signal strength
Battery charge
306
Indicators
Connection status
Battery charge
Call area
Signal strength
Good (Blue)
Full
“Rm”: Roaming area
Excellent
Conditions
Not connected
Empty
Poor
3-2. Using the multimedia system
Making a call
Once a Bluetooth
®
phone is registered, you can make a call using the following procedure:
■ Dialing
Display the phone screen. (
P. 305)
Select the “Dial Pad” tab and enter a phone number.
To delete the input phone number, select .
For the first digit, you can enter “+” by selecting “
” for a while.
Press the switch on the steering wheel or select .
■
Dialing from the contacts list
You can dial a number from the contact data imported from your cellular phone. The system has one contact for each registered phone. Up to 2500 contacts may be stored in each contact.
(
P. 308)
Display the phone screen. (
P. 305)
Select “Contacts” tab.
Choose the desired contact to call from the list.
Choose the number and then press the switch on the steering wheel or select .
3
307
3-2. Using the multimedia system
■
When the contact is empty
You can transfer the phone numbers in a Bluetooth
®
phone to the system.
Operation methods differ between PBAP (Phone Book Access
Profile) compatible and PBAP incompatible Bluetooth
®
phones. If the cellular phone does not support either PBAP or OPP (Object
Push Profile) service, you cannot transfer contacts.
● For PBAP compatible Bluetooth ®
phones
When “Automatic Contact/History
Transfer” is set to on (P. 322)
Select the “Contacts” tab.
Check that a confirmation screen is displayed when the operation is complete.
Transfer the contact data to the system using a Bluetooth
®
phone.
When “Automatic Contact/History Transfer” is set to off
Select the “Contacts” tab.
Select the desired item.
Select to transfer new contacts from a cellular phone, select “Always” and then enable “Automatic Transfer”.
Select to transfer all the contacts from a connected cellular phone only once.
Select to cancel transferring.
Check that a confirmation screen is displayed when the operation is complete.
308
3-2. Using the multimedia system
● For PBAP incompatible but OPP compatible Bluetooth ®
phones
Select the “Contacts” tab.
Follow the steps in “Update contacts from phone” from
“STEP 2”. (
P. 323)
■
Calling using favorites list
You can make a call using numbers registered in the contact.
Display the phone screen. (
P. 305)
Select “Favorites” tab.
Select the desired number to make a call.
3
309
3-2. Using the multimedia system
■
Dialing from call history
You can make a call using the call history, which has the 3 functions below.
: calls which you missed
: calls which you received
: calls which you made
Display the phone screen. (
P. 305)
Select “Call History” tab.
Select or the desired entry from the list.
When is selected
Check that the “Call” screen is displayed.
When the desired contact is selected
Select the desired number.
Check that the “Call” screen is displayed.
■ Call history list
● If you make a call to or receive a call from a number registered in the contact, the name is displayed in the call history.
● If you make multiple calls to the same number, only the last call made is displayed in the call history.
■ International calls
You may not be able to make international calls, depending on the mobile phone in use.
310
3-2. Using the multimedia system
Receiving a call
When a call is received, the following screen is displayed together with a sound.
■ To answer the phone
Press the switch on the steering wheel or select .
■
To refuse a call
Press the switch on the steering wheel or select .
■
To adjust the incoming call volume
Turn the “PWR·VOL” knob.
■ International calls
Received international calls may not be displayed correctly depending on the cellular phone in use.
3
311
3-2. Using the multimedia system
Speaking on the phone
The following screen is displayed when speaking on the phone.
■ To adjust the call volume
Select “-” or “+”. You can also adjust the volume using the volume knob.
■ To prevent the other party from hearing your voice
Select “Mute”.
■ Inputting tones
When using phone services such as an answering service or a bank, you can store phone numbers and code numbers in the contact.
Select “0-9”.
Input the number.
● Release Tones
“Release Tones” appear when a continuous tone signal(s) containing a “w” is registered in the contact list.
Select “Release Tones”.
312
3-2. Using the multimedia system
■ Release Tones
● A continuous tone signal is a character string that consists of numbers and the characters “p” or “w”. (e.g.056133w0123p#1
)
● When the “p” pause tone is used, the tone data up until the next pause tone will be automatically sent after 2 seconds have elapsed. When the
“w” pause tone is used, the tone data up until the next pause tone will be automatically sent after a user operation is performed.
● Release tones can be used when automated operation of a phone based service such as an answering machine or bank phone service is desired.
A phone number with continuous tone signals can be registered in the contact list.
● Tone data after a “w” pause tone can be operated on voice command during a call.
■
To transfer a call
Select “Handset Mode” to change from a hands-free call to a cellular phone call.
Select “Handset Mode” to off from a cellular phone call to a handsfree call.
■
Transmit volume setting
Select “Transmit Volume”.
Select the desired level for the transmit volume.
Select “OK”.
■
To hang up
Press the switch on the steering wheel or select .
3
313
3-2. Using the multimedia system
■
Call waiting
When a call is interrupted by a third party while talking, an incoming call message will be displayed.
To talk with the other party:
Press the switch on the steering wheel or select .
To refuse the call:
Press the switch on the steering wheel or select .
Every time you press the switch on the steering wheel or select during call waiting, you will be switched to the other party.
■ Transferring calls
● If you transfer from the cellular phone to hands-free, the hands-free screen will be displayed, and you can operate the system using the screen.
● Transfer method and operation may vary according to the cellular phone used.
● For operation of the cellular phone in use, see the phone’s manual.
■ Call waiting operation
Call waiting operation may differ depending on your phone company and cellular phone.
314
3-2. Using the multimedia system
Bluetooth
®
phone message function
Received messages can be forwarded from the connected
Bluetooth
®
phone, enabling checking and replying using the multimedia system.
Depending on the type of Bluetooth
®
phone connected, received messages may not be transferred to the message inbox.
If the phone does not support the message function, this function cannot be used.
■ Displaying “Message Inbox” screen
Press the switch on the steering wheel or press the button.
Select on the phone screen.
Check that the “Message Inbox” screen is displayed.
3
■ Receiving a message
When an e-mail/SMS/MMS is received, the incoming message screen pops up with sound and is ready to be operated on the screen.
E-mail: Select to check the message.
Select to refuse the message.
Select to call the message sender.
315
3-2. Using the multimedia system
■ Receiving a message
● Depending on the cellular phone used for receiving messages, or its registration status with the navigation system, some information may not be displayed.
● The pop up screen is separately available for incoming e-mail and SMS/
MMS messages under the following conditions:
E-mail:
• “Incoming E-mail Display” is set to “Full Screen”. (
P. 329)
• “E-mail Notification Popup” is set to on. (
P. 329)
SMS/MMS:
• “Incoming SMS/MMS Display” is set to “Full screen”. (
P. 329)
• “SMS/MMS Notification Popup” is set to on. (
P. 329)
■
Checking the messages
Display the “Message Inbox” screen. (
P. 315)
Select the desired message from the list.
Check that the message is displayed.
E-mails: Select “Mark Unread” or “Mark Read” to mark mail unread or read on the “Message Inbox” screen.
This function is available when
“Update Message Read Status on
Phone” is set to on (
P. 329)
Select to make a call to the sender.
Select to have messages read out. To cancel this function, select “Stop”.
Select to display the previous or next message.
Select to reply the message.
316
3-2. Using the multimedia system
■ Check the messages
● Depending on the type of Bluetooth
®
phone being connected, it may be necessary to perform additional steps on the phone.
● Messages are displayed in the appropriate connected Bluetooth
® phone’s registered mail address folder.
Select the tab of the desired folder to be displayed.
● Only received messages on the connected Bluetooth
®
phone can be displayed.
● The text of the message is not displayed while driving.
● When “Automatic Message Readout” is set to on, messages will be automatically read out. (
P. 329)
● Turn the “PWR
VOL” knob to adjust the message read out volume.
● The message read out function is available even while driving.
■
Replying to a message
Display the “Message Inbox” screen. (
P. 315)
Select the desired message from the list.
Select “Quick Message”.
Select the desired message.
Select “Send”.
● Editing quick reply message
This operation cannot be performed while driving.
Select “Quick Message”.
Select corresponding to the desired message to edit.
Select “OK” when editing is completed.
3
317
3-2. Using the multimedia system
■
Calling the message sender
Calls can be made to an e-mail/SMS/MMS message sender’s phone number.
Display the “Message Inbox” screen. (
P. 315)
Select the desired message.
Select .
Check that the “Call” screen is displayed.
● Calling from a number within a message
Calls can be made to a number identified in a message’s text area.
Display the “Message Inbox” screen. (
P. 315)
Select the desired message.
Select the text area.
Select corresponding to the desired number.
Check that the “Call” screen is displayed.
● Calling from the incoming message screen
P. 314
318
3-2. Using the multimedia system
Using the steering wheel switches (if equipped)
The steering wheel switches can be used to operate a connected cellular phone.
■ Operating a telephone using the steering wheel switches
Off hook switch
• Make a call
• Receive a call
• Display “Phone” screen
On hook switch
• End a call
• Refuse a call 3
319
3-2. Using the multimedia system
Bluetooth
®
phone settings
You can adjust the hands-free system to your desired settings.
■ “Phone/Message Settings” screen
To display the screen shown below, press the “SETUP” button, and select “Phone” on the “Setup” screen.
Set the phone connection
(
P. 286)
Sound Settings (
P. 320)
Contact/Call History Settings
(
P. 322)
Messaging Settings (
P. 329)
Phone Display Settings
(
P. 331)
■ Sound setting
Display the “Phone/Message Settings” screen. (
P. 320)
Select “Sound Settings” on the “Phone/Message Settings” screen.
Set the desired ringtone.
Adjust the ringtone volume.
Adjust the message readout volume.
Set the desired incoming
SMS/MMS tone.
Adjust the incoming SMS/
MMS tone volume.
Set the incoming e-mail tone.
Adjust the incoming e-mail tone volume.
Adjust the default volume of the other party’s voice.
320
■ To return to the default settings
Select “Default”, and then “Yes”.
3-2. Using the multimedia system
3
321
3-2. Using the multimedia system
Contact/Call history settings
The contact can be transferred from a Bluetooth
®
phone to the system. The contact also can be added, edited and deleted.
322
The call history can be deleted and contact and favorites can be changed.
Display the “Phone/Message Settings” screen. (
P. 320)
Select “Contact/Call History Settings”.
Select the desired item to be set.
For PBAP compatible
Bluetooth
®
phones, select to set automatic contact/history transfer on/off. When set to on, the phone’s contact data and history are automatically transferred.
Select to update contacts from the connected phone.
(
P. 323)
Select to sort contacts by the first name or last name field.
Select to add contacts to the favorites list. (
P. 327)
Select to delete contacts from the favorites list. (
P. 328)
Select to display contact images.
Select to clear contacts from the call history.
Select to add new contacts to the contact list.
* (
P. 325)
Select to edit contacts in the contact list.
* (
P. 325)
3-2. Using the multimedia system
Select to delete contacts from the contact list.
* (
P. 326)
Select to reset all setup items.
*
* : For PBAP compatible Bluetooth
® phones only, this function is available when “Automatic Contact/
History Transfer” is set to off.
(
P. 322)
■
Update contacts from phone
Operation methods differ between PBAP compatible and PBAP incompatible but OPP compatible Bluetooth
®
phones.
If your cellular phone is neither PBAP nor OPP compatible, the contacts cannot be transferred.
● For PBAP Compatible Bluetooth ®
Phones
Select “Update Contacts from Phone”.
Check that a confirmation screen is displayed when the operation is complete.
This operation may be unnecessary depending on the type of cellular phone.
Depending on the type of cellular phone, OBEX authentication may be required when transferring contact data. Enter “1234” into the
Bluetooth
®
phone.
If another Bluetooth
®
device is connected when transferring contact data, depending on the phone, the connected Bluetooth
®
device may need to be disconnected.
Depending on the type of Bluetooth
®
phone being connected, it may be necessary to perform additional steps on the phone.
3
323
