advertisement
![Charging the battery. Ingenico Tetra Move/5000, Move3500 | Manualzz Charging the battery. Ingenico Tetra Move/5000, Move3500 | Manualzz](http://s3.manualzz.com/store/data/056065499_1-ca0d4cfabd6c944afda593051312f442-360x466.png)
Charging the battery
When does the battery need to be charged?
• On initial startup. The battery should be charged for 16 hours under the environmental conditions stated earlier in this guide.
• When used daily on battery power only. The terminal will automatically recharge its battery each time it is placed on its base.
• When used with a terminal power supply: connect the power supply to
Move/3500 power connector.
How can the battery be charged?
Using the base
• Place the terminal on its base, charging will automatically begin.
Using the terminal power supply
• Connect the terminal power supply unit to the terminal charging port on the left of the terminal.
• The battery symbols are:
Battery charge greater than 80%
Battery charge greater than 60% and less than 80%
Battery charge greater than 40% and less than 60%
Battery charge greater than 20% and less than 40%
Battery charge less than 20%
Terminal powered by external power supply, battery full charge
• The environment in which the charge takes place influences battery lifetime and autonomy (number of transactions)
• The optimal conditions are as follows:
Charge away from any external heat source (radiator, sun, enclosed area etc.)
Page 13
The optimal temperature is between +15°C and +25°C
Move/3500 User Guide Copyright© 2017 Ingenico
advertisement
Related manuals
advertisement
Table of contents
- 2 Table of contents
- 6 Introduction
- 6 Contents of box
- 7 Overview of Move
- 8 Keyboard details and functionality
- 8 Switching ON / OFF terminal
- 9 Installation
- 9 Location of the Move
- 9 Operating Condition
- 9 Battery Charging Conditions
- 9 Storage Conditions
- 10 Terminal Connections
- 10 µSD Memory Card
- 11 Opening the back cover
- 11 SAMs & SIMs
- 12 Battery
- 12 Main Characteristics
- 12 Installing the battery
- 13 Charging the battery
- 14 Replacing the battery
- 15 R40 Paper Roll
- 16 Installing a Paper Roll
- 17 Card Reading
- 17 Magnetic Stripe Card
- 17 Chip Card
- 17 Contactless Card
- 18 Terminal Base Overview
- 19 Display/Icons
- 19 Terminal Operation Icons
- 20 GPRS Terminal
- 21 Supervisor Functions
- 21 Supervisor Code
- 22 Voice Referral Password
- 23 Terminal Configuration
- 25 Transaction Selection
- 26 Data Input
- 27 Sale – Card Details Keyed
- 28 Sale – Swiped Card
- 29 Sale – Inserted Card
- 30 Sale – Contactless
- 31 Contactless High Value Payment (HVP) – Wallet Payments
- 32 Sale with Gratuity
- 33 Refund
- 35 Refund with Gratuity
- 35 Present/Insert/Swipe the customer’s card or press
- 36 Remove the customer’s card from the terminal
- 37 Purchase with Cashback (PWCB) Swiped Card
- 37 PWCB Swiped Card
- 38 PWCB Inserted Card
- 39 Cash Advance
- 39 Cash Advance – Swipe Card
- 40 Cash Advance – Insert Card
- 41 Reversal
- 42 Pre-Authorisation (Pre-Auth)
- 43 Completion
- 43 Completion Swipe Card
- 44 Completion Insert Card
- 45 Account Verification
- 45 Account Verification Swipe Card
- 46 Account Verification Insert Card
- 47 Force Transaction
- 49 Sample Receipts
- 49 End Of Day Report
- 50 Not Authorised Receipts
- 51 Cancelled Receipts
- 51 Waiter Setup Receipts
- 52 Gratuity (Verified by PIN) Receipts
- 53 Gratuity (Verified by Signature) Receipts
- 53 Sale (Verified by Signature) Receipts
- 54 Sale (Verified by PIN) Receipts
- 54 Refund (Verified by Signature) Receipts
- 55 Self-Install Receipt
- 56 Reports
- 57 X-Totals / Z-Totals
- 58 WaiterTotals
- 59 Waiter Totals
- 60 End-of-Day-Banking
- 61 Banking Totals Agree
- 62 Banking Totals Not Agreed
- 63 Function Codes
- 63 Selecting Function Codes
- 64 Function 34 System Security
- 65 Function 91 Mobile Network Selection
- 66 Function 40 Waiter Setup
- 66 Add Waiter
- 67 Delete Waiter
- 67 Print Waiters
- 68 Change Name
- 69 Delete All
- 69 Create Defaults
- 70 Function 30 Set Date and Time
- 71 Recommendations
- 71 Safety
- 74 Security of the Terminal
- 75 Fixed Installation
- 76 Standards
- 77 Troubleshooting
- 78 Notes