advertisement
![Replacing the battery. Ingenico Tetra Move/5000, Move3500 | Manualzz Replacing the battery. Ingenico Tetra Move/5000, Move3500 | Manualzz](http://s3.manualzz.com/store/data/056065499_1-ca0d4cfabd6c944afda593051312f442-360x466.png)
Replacing the battery
It is imperative to use a battery authorized by Ingenico. There is danger of explosion if battery used is not approved by Ingenico
•
Remove the terminal from its base
•
Turn it off by pressing and simultaneously for about one second
•
Remove the back cover (see section “installing battery”)
•
Carefully disconnect battery, following the instructions below a) Unlock the connector by pressing the locking mechanism as indicated by F1 arrow while pulling this connector (F2 arrow) Release traction on it as soon as the connector comes unclipped b) Finish extracting connector by tilting it slightly
(F3 arrow) to bring it away from the terminal housing
•
Inform the terminal that battery will be replaced (*). To do so, start the terminal without battery by fitting it on its base, or connecting terminal power supply
•
Remove terminal from base or disconnect terminal power supply
•
Connect and install the new battery by following the instructions in section 4.5.2 “Installing battery”
•
Close the back cover and charge the new battery. See section
«xxxxxxx0 Charging the Battery»
•
In order to preserve the environment, dispose used battery at appropriate site in compliance with recycling legislation
(*) The terminal memorizes that there is no battery simply by powering up.
It will then correctly perform a full recharge with the next battery
Page 14 Move/3500 User Guide Copyright© 2017 Ingenico
advertisement
Related manuals
advertisement
Table of contents
- 2 Table of contents
- 6 Introduction
- 6 Contents of box
- 7 Overview of Move
- 8 Keyboard details and functionality
- 8 Switching ON / OFF terminal
- 9 Installation
- 9 Location of the Move
- 9 Operating Condition
- 9 Battery Charging Conditions
- 9 Storage Conditions
- 10 Terminal Connections
- 10 µSD Memory Card
- 11 Opening the back cover
- 11 SAMs & SIMs
- 12 Battery
- 12 Main Characteristics
- 12 Installing the battery
- 13 Charging the battery
- 14 Replacing the battery
- 15 R40 Paper Roll
- 16 Installing a Paper Roll
- 17 Card Reading
- 17 Magnetic Stripe Card
- 17 Chip Card
- 17 Contactless Card
- 18 Terminal Base Overview
- 19 Display/Icons
- 19 Terminal Operation Icons
- 20 GPRS Terminal
- 21 Supervisor Functions
- 21 Supervisor Code
- 22 Voice Referral Password
- 23 Terminal Configuration
- 25 Transaction Selection
- 26 Data Input
- 27 Sale – Card Details Keyed
- 28 Sale – Swiped Card
- 29 Sale – Inserted Card
- 30 Sale – Contactless
- 31 Contactless High Value Payment (HVP) – Wallet Payments
- 32 Sale with Gratuity
- 33 Refund
- 35 Refund with Gratuity
- 35 Present/Insert/Swipe the customer’s card or press
- 36 Remove the customer’s card from the terminal
- 37 Purchase with Cashback (PWCB) Swiped Card
- 37 PWCB Swiped Card
- 38 PWCB Inserted Card
- 39 Cash Advance
- 39 Cash Advance – Swipe Card
- 40 Cash Advance – Insert Card
- 41 Reversal
- 42 Pre-Authorisation (Pre-Auth)
- 43 Completion
- 43 Completion Swipe Card
- 44 Completion Insert Card
- 45 Account Verification
- 45 Account Verification Swipe Card
- 46 Account Verification Insert Card
- 47 Force Transaction
- 49 Sample Receipts
- 49 End Of Day Report
- 50 Not Authorised Receipts
- 51 Cancelled Receipts
- 51 Waiter Setup Receipts
- 52 Gratuity (Verified by PIN) Receipts
- 53 Gratuity (Verified by Signature) Receipts
- 53 Sale (Verified by Signature) Receipts
- 54 Sale (Verified by PIN) Receipts
- 54 Refund (Verified by Signature) Receipts
- 55 Self-Install Receipt
- 56 Reports
- 57 X-Totals / Z-Totals
- 58 WaiterTotals
- 59 Waiter Totals
- 60 End-of-Day-Banking
- 61 Banking Totals Agree
- 62 Banking Totals Not Agreed
- 63 Function Codes
- 63 Selecting Function Codes
- 64 Function 34 System Security
- 65 Function 91 Mobile Network Selection
- 66 Function 40 Waiter Setup
- 66 Add Waiter
- 67 Delete Waiter
- 67 Print Waiters
- 68 Change Name
- 69 Delete All
- 69 Create Defaults
- 70 Function 30 Set Date and Time
- 71 Recommendations
- 71 Safety
- 74 Security of the Terminal
- 75 Fixed Installation
- 76 Standards
- 77 Troubleshooting
- 78 Notes