- Computers & electronics
- Telecom & navigation
- Telephones
- Aiphone
- IXG-MK Guard Station
- Operation manual
advertisement
3
How to use
Answering a call
Placing / Answering a Call
When there is an incoming call, the status indicator flashes and the ringtone plays.
Video of the destination station is displayed, and it is able to communicate by answering the call.
1.
When receiving a call, lift the handset or tap .
Note
Alternately,
• Depending on the configuration, the ringtone may be heard from a separately installed speaker or other device.
• If the communication time set in advance is exceeded on the station of the other party, communication automatically ends. A notification tone sounds approximately 10 seconds before ending. The notification tone may not sound depending on the configuration.
• If a page with a higher priority is received from another station during communication, the call will be interrupted and the station will switch to the page.
• If a page or a call with a higher priority is received from another station while receiving a call, the station will switch to the page or call with a higher priority.
• The ringtone may not sound, depending on the configuration.
• Topping during communication turns off the microphones of the handset and the station as well as camera video. Tap to turn them back on.
• Refer to ( → page 16) for how to view the
screen when receiving a call.
) for operations when receiving a call.
2.
Speak with the other party
• When receiving two or more calls simultaneously, tap
to choose the station to communicate with. ( → page 63)
• When Auto Answer
( → page 80) is "ON," an individual call
from another Master Station will be answered automatically. It will not automatically answer a group call or a call from a Handset Sub Station or Door Station.
• Depending on the setting, if the electrical lock is released during incoming calls from the Entrance Station or while communicating, the incoming call or communication will end automatically after approximately 10 seconds.
• For how to view the screen during a call, refer to
operations during a call.
3.
To end the communication, hang up the handset or tap .
37
advertisement
Related manuals
advertisement
Table of contents
- 2 Literature information
- 3 Precautions
- 4 Precautions on operation
- 9 Part Names
- 11 Status Indicators
- 13 Camera View Range and Mounting Position
- 14 User Interface
- 20 Entering Text
- 21 Answering a call
- 24 Setting the date and time
- 26 About microSD card
- 27 Inserting/Removing microSD Cards
- 29 Specifying a station
- 29 Selecting / Choosing / Calling by Number
- 30 Specify a station or unit using the address book
- 31 Searching for stations
- 32 Call / Recording History
- 32 Reviewing Call History
- 33 History Screen
- 34 Placing / Answering a Call
- 34 Calling the other party
- 36 Use an external device to place a call
- 37 Answering a call
- 38 Page / Receive paging
- 38 Sending a page
- 40 Sending a message page
- 43 Contact Input Page
- 44 Receiving a page
- 46 Monitoring
- 46 Monitoring a door station
- 48 Scan Monitoring
- 50 Using Speed Dial Buttons
- 51 Checking recordings
- 51 Viewing Recordings
- 53 Understanding the Playback Screen
- 54 Play Video/Audio Recordings using a PC
- 55 Transfer
- 55 Transfer calls (during communication)
- 58 Absent Transfer
- 59 Other Transfer Options
- 60 Operations while placing a call, in communication, paging and monitoring
- 60 Unlocking a door
- 62 Placing a call on hold
- 63 Selecting a station to answer
- 64 Recording Video / Audio
- 65 Fixing the Capture Area
- 66 Adjusting video to enhance visibility
- 67 Adjusting Screen Brightness
- 68 Adjusting speaker volume
- 69 Adjusting microphone volume
- 70 Adjusting Ringtone Volume
- 71 Checking the System
- 71 Confirming Station Information
- 72 Other functions
- 72 Configuring the station sound a tone on a schedule
- 73 Sending an email
- 74 Configuring on the station
- 74 Configuring settings
- 92 How to configure the Ringtone
- 93 How to configure Absent Transfer settings
- 94 How to configure Delay Transfer settings
- 96 How to configure Schedule Transfer (Daily Schedule)
- 98 How to configure Schedule Transfer (Weekly Schedule)
- 101 How to configure Scan Monitoring
- 102 How to configure Chime Settings (Daily Schedule)
- 104 How to configure Chime Settings (Weekly Schedule)
- 106 How to configure the Status Output
- 107 How to configure Door Release settings
- 108 How to configure Relay Output Schedule (Daily Schedule)
- 110 How to configure Relay Output Schedule (Weekly Schedule)
- 112 How to configure Speed Dial Settings
- 121 Appendix
- 121 Specifications
- 121 Maintenance
- 122 Notice regarding the software
- 126 FOR PROPER USE OF THE STATION
- 126 REGULATIONS
- 127 WARRANTY