advertisement
Handle
IMPACT BUMPER INSTALLATION
1.
Using a Phillips Head screwdriver, remove screw from cord wrap bracket. Discard screw only.
Old Washer
2.
Place new washer on new screw and insert into impact bumper. Place old washer on end of screw.
Note: Make sure spring is installed as shown above.
39
3.
Insert impact bumper assembly into cord wrap bracket.
Note: Screw should be inserted inside spring from
original assembly. Do not over tighten.
www.pro-team.com 866.888.2168
ASSEMBLY
(a)
(b)
(c)
Wand
Hose Assembly with Cuffs
WAND AND HOSE APPLY TO
XP MODELS ONLY
Handle with Over
Mold and Decal
Quick
Release
Hose
Cuff
Cord Wrap
Screw
Handle
Tube
Bushing
Power Cord
Handle
Assembly
Screw
Carry Handle with
Tool Caddy
Cord Wrap Post
Final Vacuum Assembly
1.
2.
3.
Install all 3 filters:
(a) Intercept Micro Filter
(b) Motor Intake Filter
(c) Exhaust Filter
Install Power Cord and Handle with
Over Mold and Decal.
Attach with Handle Tube Bushing and
Carry Handle with Tool Caddy.
Wrap Power Cord around
Cord Wrap Post.
www.pro-team.com 866.888.2168 40
Troubleshooting
CLEARING HOSE AND WAND OBSTRUCTIONS – XP MODELS
R
E
S E T
T
SE
E
CLEARING THE BRUSH ROLL
Obstructions such as hair, string, and throw rugs may cause the red brush indicator light to be illuminated and the power nozzle to shut off.
1.
Turn off vacuum and unplug power cord from outlet.
2.
On underside of vacuum, pull out, or cut away, obstructions on the brush roll. (Figure A)
Figure A
Airflow path and possible obstruction locations
3.
Press the reset button on top side of powerhead. Plug-in power cord, and restart motor (Figure A).
F
IG
.
1
Quick release tabs
F
IG
. 2
CLEARING HOSE & WAND
Obstructions in hoses and wands may reduce or eliminate suction.
1.
Familiarize yourself with air flow path and possible obstruction locations
(Figure B).
2.
To determine obstruction location, remove wand from port. (Figure C). Turn on vacuum and place hand over wand opening to check for proper suction.
If no suction exists, blockage is at location A or B (as shown in Figure B) and proceed to Step 3. If there is proper suction, the blockage is at location C or
D (as shown in Figure B) and proceed to Step 5.
Figure B
F
IG
. 3
Lower air duct
3.
4.
Open Bag Housing Cover (F
IG
. 1) and replace Intercept Micro Filter. A full filter will restrict airflow.
Wand opening
Wand port
Figure C
Wand port
Wand guide
Lower air duct
Figure D
5.
6.
7.
Remove hose from the bag housing cover by using the quick release tabs.
(F
IG
. 2). Look into upper hose and wand. Shake or insert broom handle to clear any visible debris. Replace hose and wand on vacuum.
If blockage is not in the wand or upper hose, disconnect the lower air duct hose on the back of the power nozzle (F
IG
3). Visually check the lower air duct hose for debris and remove. To check for unobstructed air flow, turn on vacuum and place hand over opening on lower air duct. If you feel proper suction, reconnect lower air duct and resume vacuuming. If blockage is not in lower air duct hose, proceed to step 6.
With bottom air duct hose and upper hose and wand disconnected, carefully insert a broom handle (or any similar item like a short length of hose, pipe, etc) approximately 14 inches into wand guide on top of vacuum housing
(Figure D) to dislodge obstruction or debris. Debris should then drop or move into the lower air duct hose where you can then remove it with your hand
(F
IG
3).
Reconnect the lower air duct hose and upper hose assembly, and turn on the vacuum.
41 www.pro-team.com 866.888.2168
Troubleshooting
CLEARING HOSE AND WAND OBSTRUCTIONS – HEPA MODELS
CLEARING THE BRUSH ROLL
Obstructions such as hair, string, and throw rugs may cause the red brush indicator light to be illuminated and the power nozzle to shut off.
1.
Turn off vacuum and unplug power cord from outlet.
2.
On underside of vacuum, pull out, or cut away, obstructions on the brush roll. (Figure A).
Figure A
R
E
S E T
T
SE
E
3.
Press the reset button on top side of powerhead. Plug-in power cord, and restart motor. (Figure A).
Figure B
CLEARING HOSE & WAND
Obstructions in hoses and wands may reduce or eliminate suction.
1.
Turn off vacuum and unplug power cord from outlet
2.
Open Bag Housing Cover (Figure B) and replace Intercept Micro Filter. A full filter will restrict airflow.
3.
Disconnect the lower air duct hose on the back of the power nozzle
(Figure C). Visually check the lower air duct hose for debris and remove.
Figure C
4.
To check for unobstructed air flow, turn on vacuum with bag housing cover closed and place hand over opening on lower air duct (Figure C). If you feel prope suction, reconnect lower air duct and resume vacuuming.
If blockage is not in lower air duct hose, proceed to step 5.
Port
5.
Carefully insert a broom handle (or any similar item like a short length of hose, pipe, etc ) approximately 14 inches into guide on top of vacuum housing (Figure D) to dislodge obstruction or debris. Debris should then drop or move into the lower air duct where you can then remove it with your hand.
Guide
6.
Reconnect the lower air duct and upper hose assembly. Close bag housing cover and power on the vacuum.
Lower air duct
Figure D
www.pro-team.com 866.888.2168 42
P.O. Box 7385, Boise, Idaho 83707 • 866.888.2168
www.pro-team.com
#106243 Revised 12/12
advertisement
Related manuals
advertisement