- Industrial & lab equipment
- Personal safety & protection
- Fire protection
- Faraday
- MPC-7000
- User manual
City Tie (Optional City Tie Board P/N CT-1K). Faraday MPC-7000, MPC-6000, RND-2
Add to My manuals76 Pages
advertisement
MPC-6000 / MPC-7000 / RND-2 INSTALLATION, OPERATION AND MAINTENANCE MANUAL
City Tie (Optional City Tie Board P/N CT-1K)
CA Reverse Polarity: Selectable for Alarm with Trouble or Alarm only operation
• Supervised by receiver for short or open circuit
• Supervised by control unit for grounded circuit
• Voltage: 24 VDC nominal
• Current: 0.020A maximum (normal or trouble)
• Current: 0.025A maximum (shorted)
• Ripple: 1.5 VAC maximum
CT Reverse Polarity: Programmable for Trouble or Supervisory or both
• Supervised by receiver for short or open circuit
• Supervised by control unit for grounded circuit
• Voltage: 24 VDC nominal
• Current: 0.020A maximum (normal or alarm)
• Current: 0.025A maximum (shorted)
• Ripple: 1.5 VAC maximum
LE Local Energy
• Not power limited
• Supervised for open or grounded circuit by control unit
• Voltage: 24 VDC nominal
• Standby Current: 0.007A maximum
• Alarm Current: 0.400A maximum
• Ripple: 1.5 VAC maximum
• Maximum wire loop resistance: 30 ohms
• Trip coil impedance: 14.5 ohms
DACT Circuit (Optional DACT Board MPC-DACT) limited
• Supervised for short or open circuit
• Maximum Voltage: 60 VDC
• Maximum Current (shorted): 0.100A
Additional Transformer (Optional Transformer Assembly NPE-1)
• Provides an additional 3.0A of NAC power (max 1 per panel)
18
advertisement
Related manuals
advertisement
Table of contents
- 7 INTRODUCTION
- 7 CONTROL UNIT LIMITATIONS
- 8 INSTALLATION AND WARRANTY INFORMATION
- 8 Installer Information
- 8 Original Purchaser Information
- 9 PREFACE
- 10 DESCRIPTIONS
- 10 MPC-6000 SYSTEM DESCRIPTION
- 10 Power Supply
- 10 X1 Addressable Device Circuit
- 11 Notification Appliance Circuits
- 11 Serial Interface Circuit
- 11 Status Relays
- 11 Programming Port
- 12 MPC-7000 SYSTEM DESCRIPTION
- 12 Power Supply
- 12 X1 Addressable Device Circuits
- 13 Notification Appliance Circuits
- 13 Serial Interface Circuit
- 13 Status Relays
- 13 Programming Port
- 14 RND-2 SYSTEM DESCRIPTION
- 14 Power Supply
- 15 Serial Interface Circuit
- 15 Status Relays
- 15 Programming Port
- 16 OPTIONAL MODULES
- 16 CT-1K City Tie Board (MPC-6000 / MPC-7000 / RND-2)
- 16 MPC-DACT DACT Board (MPC-6000 / MPC-7000 / RND-2)
- 16 NPE-1 Transformer Assembly (MPC-6000 / MPC-7000)
- 16 NEM-1 NAC Expansion Board (MPC-7000)
- 16 LEM-1 Loop Expander Board (MPC-7000)
- 16 FDLC Loop Driver Board (MPC-7000)
- 16 HBC-1 Battery Charger (MPC-7000)
- 16 Battery Sets
- 17 AUXILIARY MODULES
- 17 Serial LCD Annunciator
- 17 Serial Relay Unit and Serial Relay Extender
- 17 Serial Annunciator Unit and Serial Annunciator Extender
- 17 RSE-300 Remote Signal Expander
- 18 X1 ADDRESSABLE DEVICES
- 18 Fire Smart™ Smoke Detector
- 18 Heat Detectors
- 18 Addressable Modules (Monitor and Control)
- 18 Manual Stations
- 18 Programming X1 Devices
- 19 EVENT HISTORY
- 20 GENERAL DESIGN FEATURES
- 20 Environmental
- 20 Power Limiting
- 20 Ground Fault Detection
- 20 NAC Operation
- 20 Transient Protection
- 20 Security Features
- 21 REGULATORY STANDARDS
- 21 Federal Communications Commission
- 21 Underwriters Laboratories
- 22 GENERAL SPECIFICATIONS
- 22 Environmental
- 22 Primary Supply
- 22 Secondary and Trouble Power Supply
- 22 Auxiliary Power Outputs
- 22 Status Relays
- 23 Notification Appliance Circuits
- 23 Serial Interface Circuit
- 23 X1 Addressable Device Circuits
- 24 City Tie (Optional City Tie Board P/N CT-1K)
- 24 DACT Circuit (Optional DACT Board MPC-DACT)
- 24 Additional Transformer (Optional Transformer Assembly NPE-1)
- 25 CONTROL UNIT OPERATION
- 25 OPERATION INSTRUCTIONS
- 25 Standby Condition
- 25 Alarm Conditions
- 26 Trouble Conditions
- 27 Supervisory Conditions
- 27 Pre-Alarm Conditions
- 27 Maintenance
- 28 ADDITIONAL OPERATING PROCEDURES
- 28 Lamp Test
- 28 Drill
- 28 Recall
- 28 Alert
- 29 History
- 30 MPC-6000 / MPC-7000 / RND-2 OPERATING INSTRUCTIONS
- 30 Alarm Operation
- 30 Authorized Personnel Only
- 30 Trouble Operation
- 30 Normal Standby Condition
- 31 RDC-2 OPERATING INSTRUCTIONS
- 31 Alarm Operation
- 31 Authorized Personnel Only
- 31 Trouble Operation
- 31 Normal Standby Condition
- 32 CONTROL UNIT INSTALLATION
- 32 PARTS SUPPLIED – MPC-6000 / MPC-7000 / RND
- 32 Enclosure Packages (Black or Red)
- 32 Electronics Package MPC-6000 / MPC
- 32 Electronics Package RND
- 32 With NPE-1 Transformer Package
- 32 CAUTION
- 33 CONTROL UNIT LOCATION
- 33 INSTALLATION
- 33 ENCLOSURE MOUNTING
- 34 MPC-6000 and RND-2 Enclosure Mounting Pictures
- 35 MPC-7000 Enclosure Mounting Pictures
- 35 Remove Knock-Outs
- 36 Main Board Installation – P/N MPC6-MB / MPC7-MB
- 37 Bridge Rectifier Installation – P/N 130-PM
- 38 Transformer Mounting – P/N NPE
- 39 Loop Driver Board(s) Mounting – P/N FDLC
- 40 Display Board Installation – P/N MPC-DB or RND2-DB
- 40 Ground Wire Installation – P/N
- 41 SYSTEM WIRING
- 41 AC Supply Connection
- 42 Battery Installation
- 42 Powering the Control Unit
- 42 Optional Modules
- 42 Check System Operation
- 42 WIRING
- 43 Control Unit Wiring Overview
- 43 Wiring Entering Enclosure
- 43 Install Wiring
- 44 Wiring Separation
- 45 Primary And Secondary Power Wiring
- 45 Status Relays And Auxiliary Power Outputs Wiring
- 46 MPC-6000 System Power Requirements (Does not include NAC power)
- 46 RND-2 System Power Requirements
- 46 MPC-7000 System Power Requirement (Does not include NAC power)
- 47 Auxiliary Power Supply
- 47 Battery Size Calculations
- 48 NAC Wiring
- 49 Serial Interface Circuit
- 50 Serial Remote Device Wiring Overview
- 51 X1 Addresable Device Circuit(s)
- 52 X1 Addressable Device Wiring Diagrams
- 54 PROGRAMMING THE CONTROL UNIT
- 54 KEYPAD PROGRAMMING
- 54 PC PROGRAMMING
- 54 PROGRAMMING SECURITY
- 55 MAINTENANCE
- 55 GENERAL
- 56 QUICK TEST
- 57 APPENDIX-A: REFERENCE DATA
- 57 WIRE SELECTION GUIDES
- 57 Resistance of Solid Copper Wire
- 57 Notification Appliance Circuit Wire Selection Guide
- 57 Maximum Wire Loop Distance (Feet)
- 58 Addressable Device Circuit Wire Selection Guide
- 58 Line Resistance Graph
- 59 BATTERY SIZE CALCULATIONS
- 59 MPC-6000 Current Calculations
- 59 RND-2 Current Calculations
- 59 MPC-7000 Current Calculation
- 61 Auxiliary Module Battery Calculations
- 61 Device Current Calculations
- 62 Total System Currents
- 62 Battery Size
- 63 APPENDIX-B: COMPATIBLE DEVICES
- 63 DEVICES FOR ADDRESSABLE DEVICE CIRCUITS
- 63 Faraday X1 Manual Pull Stations
- 63 Faraday X1 Modules
- 63 Faraday X1 Photo Electric Detectors
- 63 Faraday X1 Bases
- 63 Faraday X1 Accessories
- 64 DEVICES FOR NOTIFICATION APPLIANCE CIRCUITS
- 64 Notification Appliances
- 67 Accessory Devices
- 67 DEVICES FOR AUXILIARY POWER OUTPUTS
- 67 Door Holders
- 67 Relays
- 68 APPENDIX-C: TROUBLESHOOTING
- 68 DEFINITIONS FOR EVENT HISTORY ENTRIES
- 68 A. General
- 69 B. System Troubles
- 70 C. System Events
- 71 APPENDIX-D: MODULE INSTALLATION INSTRUCTIONS LIST
- 72 APPENDIX-E: GLOSSARY