- Industrial & lab equipment
- Personal safety & protection
- Fire protection
- Faraday
- MPC-7000
- User manual
advertisement
MPC-6000 / MPC-7000 / RND-2 INSTALLATION, OPERATION AND MAINTENANCE MANUAL
Supervisory Conditions
In case of a supervisory condition, the system supervisory LED activates (ON – flashing) and the sounder activates (ON – pulsing). When the supervisory has been listed, the buzzer is silenced by pressing the “ACKNOWLEDGE” button. The supervisory trouble LED changes to steady – ON. When the supervisory is cleared, the supervisory condition is still indicated until it is acknowledged.
Pre-Alarm Conditions
• A pre-alarm condition is annunciated by Pre-alarm LEDs and buzzers on the control unit and LCD Annunciators and Remote Processors. The LEDs flash and buzzers are on steady until acknowledgment.
• Acknowledging the Pre-alarm condition puts LEDs on steady and buzzers off.
• If pre-alarm has been acknowledged and the system restores to normal, the condition clears. If the system proceeds into an alarm condition, the pre-alarm condition clears whether or not it has been acknowledged and is replaced by alarm.
Maintenance
In order to insure continued safe and reliable operation of the fire alarm system, periodic inspection and testing should be performed in accordance with applicable NFPA 72 standards.
If the system has remote connections to the Fire Department or other monitor, be sure to disable the remote signals and/or notify the remote monitoring station before performing test operations.
For any required service, refer to the system manual or contact a factory authorized representative.
21
advertisement
Related manuals
advertisement
Table of contents
- 7 INTRODUCTION
- 7 CONTROL UNIT LIMITATIONS
- 8 INSTALLATION AND WARRANTY INFORMATION
- 8 Installer Information
- 8 Original Purchaser Information
- 9 PREFACE
- 10 DESCRIPTIONS
- 10 MPC-6000 SYSTEM DESCRIPTION
- 10 Power Supply
- 10 X1 Addressable Device Circuit
- 11 Notification Appliance Circuits
- 11 Serial Interface Circuit
- 11 Status Relays
- 11 Programming Port
- 12 MPC-7000 SYSTEM DESCRIPTION
- 12 Power Supply
- 12 X1 Addressable Device Circuits
- 13 Notification Appliance Circuits
- 13 Serial Interface Circuit
- 13 Status Relays
- 13 Programming Port
- 14 RND-2 SYSTEM DESCRIPTION
- 14 Power Supply
- 15 Serial Interface Circuit
- 15 Status Relays
- 15 Programming Port
- 16 OPTIONAL MODULES
- 16 CT-1K City Tie Board (MPC-6000 / MPC-7000 / RND-2)
- 16 MPC-DACT DACT Board (MPC-6000 / MPC-7000 / RND-2)
- 16 NPE-1 Transformer Assembly (MPC-6000 / MPC-7000)
- 16 NEM-1 NAC Expansion Board (MPC-7000)
- 16 LEM-1 Loop Expander Board (MPC-7000)
- 16 FDLC Loop Driver Board (MPC-7000)
- 16 HBC-1 Battery Charger (MPC-7000)
- 16 Battery Sets
- 17 AUXILIARY MODULES
- 17 Serial LCD Annunciator
- 17 Serial Relay Unit and Serial Relay Extender
- 17 Serial Annunciator Unit and Serial Annunciator Extender
- 17 RSE-300 Remote Signal Expander
- 18 X1 ADDRESSABLE DEVICES
- 18 Fire Smart™ Smoke Detector
- 18 Heat Detectors
- 18 Addressable Modules (Monitor and Control)
- 18 Manual Stations
- 18 Programming X1 Devices
- 19 EVENT HISTORY
- 20 GENERAL DESIGN FEATURES
- 20 Environmental
- 20 Power Limiting
- 20 Ground Fault Detection
- 20 NAC Operation
- 20 Transient Protection
- 20 Security Features
- 21 REGULATORY STANDARDS
- 21 Federal Communications Commission
- 21 Underwriters Laboratories
- 22 GENERAL SPECIFICATIONS
- 22 Environmental
- 22 Primary Supply
- 22 Secondary and Trouble Power Supply
- 22 Auxiliary Power Outputs
- 22 Status Relays
- 23 Notification Appliance Circuits
- 23 Serial Interface Circuit
- 23 X1 Addressable Device Circuits
- 24 City Tie (Optional City Tie Board P/N CT-1K)
- 24 DACT Circuit (Optional DACT Board MPC-DACT)
- 24 Additional Transformer (Optional Transformer Assembly NPE-1)
- 25 CONTROL UNIT OPERATION
- 25 OPERATION INSTRUCTIONS
- 25 Standby Condition
- 25 Alarm Conditions
- 26 Trouble Conditions
- 27 Supervisory Conditions
- 27 Pre-Alarm Conditions
- 27 Maintenance
- 28 ADDITIONAL OPERATING PROCEDURES
- 28 Lamp Test
- 28 Drill
- 28 Recall
- 28 Alert
- 29 History
- 30 MPC-6000 / MPC-7000 / RND-2 OPERATING INSTRUCTIONS
- 30 Alarm Operation
- 30 Authorized Personnel Only
- 30 Trouble Operation
- 30 Normal Standby Condition
- 31 RDC-2 OPERATING INSTRUCTIONS
- 31 Alarm Operation
- 31 Authorized Personnel Only
- 31 Trouble Operation
- 31 Normal Standby Condition
- 32 CONTROL UNIT INSTALLATION
- 32 PARTS SUPPLIED – MPC-6000 / MPC-7000 / RND
- 32 Enclosure Packages (Black or Red)
- 32 Electronics Package MPC-6000 / MPC
- 32 Electronics Package RND
- 32 With NPE-1 Transformer Package
- 32 CAUTION
- 33 CONTROL UNIT LOCATION
- 33 INSTALLATION
- 33 ENCLOSURE MOUNTING
- 34 MPC-6000 and RND-2 Enclosure Mounting Pictures
- 35 MPC-7000 Enclosure Mounting Pictures
- 35 Remove Knock-Outs
- 36 Main Board Installation – P/N MPC6-MB / MPC7-MB
- 37 Bridge Rectifier Installation – P/N 130-PM
- 38 Transformer Mounting – P/N NPE
- 39 Loop Driver Board(s) Mounting – P/N FDLC
- 40 Display Board Installation – P/N MPC-DB or RND2-DB
- 40 Ground Wire Installation – P/N
- 41 SYSTEM WIRING
- 41 AC Supply Connection
- 42 Battery Installation
- 42 Powering the Control Unit
- 42 Optional Modules
- 42 Check System Operation
- 42 WIRING
- 43 Control Unit Wiring Overview
- 43 Wiring Entering Enclosure
- 43 Install Wiring
- 44 Wiring Separation
- 45 Primary And Secondary Power Wiring
- 45 Status Relays And Auxiliary Power Outputs Wiring
- 46 MPC-6000 System Power Requirements (Does not include NAC power)
- 46 RND-2 System Power Requirements
- 46 MPC-7000 System Power Requirement (Does not include NAC power)
- 47 Auxiliary Power Supply
- 47 Battery Size Calculations
- 48 NAC Wiring
- 49 Serial Interface Circuit
- 50 Serial Remote Device Wiring Overview
- 51 X1 Addresable Device Circuit(s)
- 52 X1 Addressable Device Wiring Diagrams
- 54 PROGRAMMING THE CONTROL UNIT
- 54 KEYPAD PROGRAMMING
- 54 PC PROGRAMMING
- 54 PROGRAMMING SECURITY
- 55 MAINTENANCE
- 55 GENERAL
- 56 QUICK TEST
- 57 APPENDIX-A: REFERENCE DATA
- 57 WIRE SELECTION GUIDES
- 57 Resistance of Solid Copper Wire
- 57 Notification Appliance Circuit Wire Selection Guide
- 57 Maximum Wire Loop Distance (Feet)
- 58 Addressable Device Circuit Wire Selection Guide
- 58 Line Resistance Graph
- 59 BATTERY SIZE CALCULATIONS
- 59 MPC-6000 Current Calculations
- 59 RND-2 Current Calculations
- 59 MPC-7000 Current Calculation
- 61 Auxiliary Module Battery Calculations
- 61 Device Current Calculations
- 62 Total System Currents
- 62 Battery Size
- 63 APPENDIX-B: COMPATIBLE DEVICES
- 63 DEVICES FOR ADDRESSABLE DEVICE CIRCUITS
- 63 Faraday X1 Manual Pull Stations
- 63 Faraday X1 Modules
- 63 Faraday X1 Photo Electric Detectors
- 63 Faraday X1 Bases
- 63 Faraday X1 Accessories
- 64 DEVICES FOR NOTIFICATION APPLIANCE CIRCUITS
- 64 Notification Appliances
- 67 Accessory Devices
- 67 DEVICES FOR AUXILIARY POWER OUTPUTS
- 67 Door Holders
- 67 Relays
- 68 APPENDIX-C: TROUBLESHOOTING
- 68 DEFINITIONS FOR EVENT HISTORY ENTRIES
- 68 A. General
- 69 B. System Troubles
- 70 C. System Events
- 71 APPENDIX-D: MODULE INSTALLATION INSTRUCTIONS LIST
- 72 APPENDIX-E: GLOSSARY