- Industrial & lab equipment
- Personal safety & protection
- Fire protection
- Faraday
- MPC-7000
- User manual
advertisement
MPC-6000 / MPC-7000 / RND-2 INSTALLATION, OPERATION AND MAINTENANCE MANUAL
ADDITIONAL OPERATING PROCEDURES
In addition to the basic fire alarm instructions above, several features are included to facilitate maintenance and increase the versatility of the system. Following are procedures to call up these functions.
Lamp Test
Lamp Test activates the buzzer and turns on all the LEDs on the user interface for 2 seconds, then reverts to its previous state.
To operate the lamp test, press the MENU button. The LCD will change to a MENU screen.
Press the button next to the “More” indication twice. Then press the button by the “Lamp Test” indication. All lamps on the unit being operated will then light. Operating the button next to “Esc” will then return the control unit to normal display. Note that the lamp test operates the indicators only on the unit being operated, and no record is reported to system history.
Drill
When selected, activates all NACs assigned to the Output Zone selected for “Drill”.
To activate a fire alarm drill, proceed as follows:
• On the MENU display, select "More".
• At the next screen, select "DRILL".
• At the next screen, select "Yes".
• Operate ALARM SILENCE to terminate drill signal.
Recall
When selected, activates all NACs assigned to Output Zones selected for “Recall”.
To signal recall after a drill, proceed as follows:
• At the next screen, select "More".
• At the next screen, select "Yes".
• Operate ALARM SILENCE to terminate recall signal.
Alert
When selected, activates all NACs assigned to the Output Zone selected for “Alert”.
To activate an alert alarm, proceed as follows:
• On the MENU display, select "ALERT".
• At the next screen, select "Yes".
• Operate ALARM SILENCE to terminate alert signal.
22
advertisement
Related manuals
advertisement
Table of contents
- 7 INTRODUCTION
- 7 CONTROL UNIT LIMITATIONS
- 8 INSTALLATION AND WARRANTY INFORMATION
- 8 Installer Information
- 8 Original Purchaser Information
- 9 PREFACE
- 10 DESCRIPTIONS
- 10 MPC-6000 SYSTEM DESCRIPTION
- 10 Power Supply
- 10 X1 Addressable Device Circuit
- 11 Notification Appliance Circuits
- 11 Serial Interface Circuit
- 11 Status Relays
- 11 Programming Port
- 12 MPC-7000 SYSTEM DESCRIPTION
- 12 Power Supply
- 12 X1 Addressable Device Circuits
- 13 Notification Appliance Circuits
- 13 Serial Interface Circuit
- 13 Status Relays
- 13 Programming Port
- 14 RND-2 SYSTEM DESCRIPTION
- 14 Power Supply
- 15 Serial Interface Circuit
- 15 Status Relays
- 15 Programming Port
- 16 OPTIONAL MODULES
- 16 CT-1K City Tie Board (MPC-6000 / MPC-7000 / RND-2)
- 16 MPC-DACT DACT Board (MPC-6000 / MPC-7000 / RND-2)
- 16 NPE-1 Transformer Assembly (MPC-6000 / MPC-7000)
- 16 NEM-1 NAC Expansion Board (MPC-7000)
- 16 LEM-1 Loop Expander Board (MPC-7000)
- 16 FDLC Loop Driver Board (MPC-7000)
- 16 HBC-1 Battery Charger (MPC-7000)
- 16 Battery Sets
- 17 AUXILIARY MODULES
- 17 Serial LCD Annunciator
- 17 Serial Relay Unit and Serial Relay Extender
- 17 Serial Annunciator Unit and Serial Annunciator Extender
- 17 RSE-300 Remote Signal Expander
- 18 X1 ADDRESSABLE DEVICES
- 18 Fire Smart™ Smoke Detector
- 18 Heat Detectors
- 18 Addressable Modules (Monitor and Control)
- 18 Manual Stations
- 18 Programming X1 Devices
- 19 EVENT HISTORY
- 20 GENERAL DESIGN FEATURES
- 20 Environmental
- 20 Power Limiting
- 20 Ground Fault Detection
- 20 NAC Operation
- 20 Transient Protection
- 20 Security Features
- 21 REGULATORY STANDARDS
- 21 Federal Communications Commission
- 21 Underwriters Laboratories
- 22 GENERAL SPECIFICATIONS
- 22 Environmental
- 22 Primary Supply
- 22 Secondary and Trouble Power Supply
- 22 Auxiliary Power Outputs
- 22 Status Relays
- 23 Notification Appliance Circuits
- 23 Serial Interface Circuit
- 23 X1 Addressable Device Circuits
- 24 City Tie (Optional City Tie Board P/N CT-1K)
- 24 DACT Circuit (Optional DACT Board MPC-DACT)
- 24 Additional Transformer (Optional Transformer Assembly NPE-1)
- 25 CONTROL UNIT OPERATION
- 25 OPERATION INSTRUCTIONS
- 25 Standby Condition
- 25 Alarm Conditions
- 26 Trouble Conditions
- 27 Supervisory Conditions
- 27 Pre-Alarm Conditions
- 27 Maintenance
- 28 ADDITIONAL OPERATING PROCEDURES
- 28 Lamp Test
- 28 Drill
- 28 Recall
- 28 Alert
- 29 History
- 30 MPC-6000 / MPC-7000 / RND-2 OPERATING INSTRUCTIONS
- 30 Alarm Operation
- 30 Authorized Personnel Only
- 30 Trouble Operation
- 30 Normal Standby Condition
- 31 RDC-2 OPERATING INSTRUCTIONS
- 31 Alarm Operation
- 31 Authorized Personnel Only
- 31 Trouble Operation
- 31 Normal Standby Condition
- 32 CONTROL UNIT INSTALLATION
- 32 PARTS SUPPLIED – MPC-6000 / MPC-7000 / RND
- 32 Enclosure Packages (Black or Red)
- 32 Electronics Package MPC-6000 / MPC
- 32 Electronics Package RND
- 32 With NPE-1 Transformer Package
- 32 CAUTION
- 33 CONTROL UNIT LOCATION
- 33 INSTALLATION
- 33 ENCLOSURE MOUNTING
- 34 MPC-6000 and RND-2 Enclosure Mounting Pictures
- 35 MPC-7000 Enclosure Mounting Pictures
- 35 Remove Knock-Outs
- 36 Main Board Installation – P/N MPC6-MB / MPC7-MB
- 37 Bridge Rectifier Installation – P/N 130-PM
- 38 Transformer Mounting – P/N NPE
- 39 Loop Driver Board(s) Mounting – P/N FDLC
- 40 Display Board Installation – P/N MPC-DB or RND2-DB
- 40 Ground Wire Installation – P/N
- 41 SYSTEM WIRING
- 41 AC Supply Connection
- 42 Battery Installation
- 42 Powering the Control Unit
- 42 Optional Modules
- 42 Check System Operation
- 42 WIRING
- 43 Control Unit Wiring Overview
- 43 Wiring Entering Enclosure
- 43 Install Wiring
- 44 Wiring Separation
- 45 Primary And Secondary Power Wiring
- 45 Status Relays And Auxiliary Power Outputs Wiring
- 46 MPC-6000 System Power Requirements (Does not include NAC power)
- 46 RND-2 System Power Requirements
- 46 MPC-7000 System Power Requirement (Does not include NAC power)
- 47 Auxiliary Power Supply
- 47 Battery Size Calculations
- 48 NAC Wiring
- 49 Serial Interface Circuit
- 50 Serial Remote Device Wiring Overview
- 51 X1 Addresable Device Circuit(s)
- 52 X1 Addressable Device Wiring Diagrams
- 54 PROGRAMMING THE CONTROL UNIT
- 54 KEYPAD PROGRAMMING
- 54 PC PROGRAMMING
- 54 PROGRAMMING SECURITY
- 55 MAINTENANCE
- 55 GENERAL
- 56 QUICK TEST
- 57 APPENDIX-A: REFERENCE DATA
- 57 WIRE SELECTION GUIDES
- 57 Resistance of Solid Copper Wire
- 57 Notification Appliance Circuit Wire Selection Guide
- 57 Maximum Wire Loop Distance (Feet)
- 58 Addressable Device Circuit Wire Selection Guide
- 58 Line Resistance Graph
- 59 BATTERY SIZE CALCULATIONS
- 59 MPC-6000 Current Calculations
- 59 RND-2 Current Calculations
- 59 MPC-7000 Current Calculation
- 61 Auxiliary Module Battery Calculations
- 61 Device Current Calculations
- 62 Total System Currents
- 62 Battery Size
- 63 APPENDIX-B: COMPATIBLE DEVICES
- 63 DEVICES FOR ADDRESSABLE DEVICE CIRCUITS
- 63 Faraday X1 Manual Pull Stations
- 63 Faraday X1 Modules
- 63 Faraday X1 Photo Electric Detectors
- 63 Faraday X1 Bases
- 63 Faraday X1 Accessories
- 64 DEVICES FOR NOTIFICATION APPLIANCE CIRCUITS
- 64 Notification Appliances
- 67 Accessory Devices
- 67 DEVICES FOR AUXILIARY POWER OUTPUTS
- 67 Door Holders
- 67 Relays
- 68 APPENDIX-C: TROUBLESHOOTING
- 68 DEFINITIONS FOR EVENT HISTORY ENTRIES
- 68 A. General
- 69 B. System Troubles
- 70 C. System Events
- 71 APPENDIX-D: MODULE INSTALLATION INSTRUCTIONS LIST
- 72 APPENDIX-E: GLOSSARY