- Industrial & lab equipment
- Personal safety & protection
- Fire protection
- Faraday
- MPC-7000
- User manual
advertisement
MPC-6000 / MPC-7000 / RND-2 INSTALLATION, OPERATION AND MAINTENANCE MANUAL
MAINTENANCE
GENERAL
The MPC-6000 / MPC-7000 / RND-2 provides a maintenance mode to allow for the setting and controlling of various features in the system. Since the RND-2 does not have devices connected to it, some of these functions are not available on the RND-2.
The maintenance functions are protected by a four digit password. To access the maintenance features press the “MENU” button four times and select “Maint. Level” from the display, enter the four digit code when prompted and then press “Enter”. The functions listed below are now accessible to the user by using the function buttons on either side of the display.
Disable/Enable Devices
Disable/ Enable Groups
Disable Zones
Disable NACs
Disable City Tie
Disable DACT
Disable Status relays
Disable/Enable Detector Applications
Quick Test
Print History
Print Sensor levels
Edit Device labels
Edit System Labels
Program a Device
Set the time
Set the date
Change the password
Clear the history
Refer to the programming manual for more information about accessing and using the maintenance level functions.
49
advertisement
Related manuals
advertisement
Table of contents
- 7 INTRODUCTION
- 7 CONTROL UNIT LIMITATIONS
- 8 INSTALLATION AND WARRANTY INFORMATION
- 8 Installer Information
- 8 Original Purchaser Information
- 9 PREFACE
- 10 DESCRIPTIONS
- 10 MPC-6000 SYSTEM DESCRIPTION
- 10 Power Supply
- 10 X1 Addressable Device Circuit
- 11 Notification Appliance Circuits
- 11 Serial Interface Circuit
- 11 Status Relays
- 11 Programming Port
- 12 MPC-7000 SYSTEM DESCRIPTION
- 12 Power Supply
- 12 X1 Addressable Device Circuits
- 13 Notification Appliance Circuits
- 13 Serial Interface Circuit
- 13 Status Relays
- 13 Programming Port
- 14 RND-2 SYSTEM DESCRIPTION
- 14 Power Supply
- 15 Serial Interface Circuit
- 15 Status Relays
- 15 Programming Port
- 16 OPTIONAL MODULES
- 16 CT-1K City Tie Board (MPC-6000 / MPC-7000 / RND-2)
- 16 MPC-DACT DACT Board (MPC-6000 / MPC-7000 / RND-2)
- 16 NPE-1 Transformer Assembly (MPC-6000 / MPC-7000)
- 16 NEM-1 NAC Expansion Board (MPC-7000)
- 16 LEM-1 Loop Expander Board (MPC-7000)
- 16 FDLC Loop Driver Board (MPC-7000)
- 16 HBC-1 Battery Charger (MPC-7000)
- 16 Battery Sets
- 17 AUXILIARY MODULES
- 17 Serial LCD Annunciator
- 17 Serial Relay Unit and Serial Relay Extender
- 17 Serial Annunciator Unit and Serial Annunciator Extender
- 17 RSE-300 Remote Signal Expander
- 18 X1 ADDRESSABLE DEVICES
- 18 Fire Smart™ Smoke Detector
- 18 Heat Detectors
- 18 Addressable Modules (Monitor and Control)
- 18 Manual Stations
- 18 Programming X1 Devices
- 19 EVENT HISTORY
- 20 GENERAL DESIGN FEATURES
- 20 Environmental
- 20 Power Limiting
- 20 Ground Fault Detection
- 20 NAC Operation
- 20 Transient Protection
- 20 Security Features
- 21 REGULATORY STANDARDS
- 21 Federal Communications Commission
- 21 Underwriters Laboratories
- 22 GENERAL SPECIFICATIONS
- 22 Environmental
- 22 Primary Supply
- 22 Secondary and Trouble Power Supply
- 22 Auxiliary Power Outputs
- 22 Status Relays
- 23 Notification Appliance Circuits
- 23 Serial Interface Circuit
- 23 X1 Addressable Device Circuits
- 24 City Tie (Optional City Tie Board P/N CT-1K)
- 24 DACT Circuit (Optional DACT Board MPC-DACT)
- 24 Additional Transformer (Optional Transformer Assembly NPE-1)
- 25 CONTROL UNIT OPERATION
- 25 OPERATION INSTRUCTIONS
- 25 Standby Condition
- 25 Alarm Conditions
- 26 Trouble Conditions
- 27 Supervisory Conditions
- 27 Pre-Alarm Conditions
- 27 Maintenance
- 28 ADDITIONAL OPERATING PROCEDURES
- 28 Lamp Test
- 28 Drill
- 28 Recall
- 28 Alert
- 29 History
- 30 MPC-6000 / MPC-7000 / RND-2 OPERATING INSTRUCTIONS
- 30 Alarm Operation
- 30 Authorized Personnel Only
- 30 Trouble Operation
- 30 Normal Standby Condition
- 31 RDC-2 OPERATING INSTRUCTIONS
- 31 Alarm Operation
- 31 Authorized Personnel Only
- 31 Trouble Operation
- 31 Normal Standby Condition
- 32 CONTROL UNIT INSTALLATION
- 32 PARTS SUPPLIED – MPC-6000 / MPC-7000 / RND
- 32 Enclosure Packages (Black or Red)
- 32 Electronics Package MPC-6000 / MPC
- 32 Electronics Package RND
- 32 With NPE-1 Transformer Package
- 32 CAUTION
- 33 CONTROL UNIT LOCATION
- 33 INSTALLATION
- 33 ENCLOSURE MOUNTING
- 34 MPC-6000 and RND-2 Enclosure Mounting Pictures
- 35 MPC-7000 Enclosure Mounting Pictures
- 35 Remove Knock-Outs
- 36 Main Board Installation – P/N MPC6-MB / MPC7-MB
- 37 Bridge Rectifier Installation – P/N 130-PM
- 38 Transformer Mounting – P/N NPE
- 39 Loop Driver Board(s) Mounting – P/N FDLC
- 40 Display Board Installation – P/N MPC-DB or RND2-DB
- 40 Ground Wire Installation – P/N
- 41 SYSTEM WIRING
- 41 AC Supply Connection
- 42 Battery Installation
- 42 Powering the Control Unit
- 42 Optional Modules
- 42 Check System Operation
- 42 WIRING
- 43 Control Unit Wiring Overview
- 43 Wiring Entering Enclosure
- 43 Install Wiring
- 44 Wiring Separation
- 45 Primary And Secondary Power Wiring
- 45 Status Relays And Auxiliary Power Outputs Wiring
- 46 MPC-6000 System Power Requirements (Does not include NAC power)
- 46 RND-2 System Power Requirements
- 46 MPC-7000 System Power Requirement (Does not include NAC power)
- 47 Auxiliary Power Supply
- 47 Battery Size Calculations
- 48 NAC Wiring
- 49 Serial Interface Circuit
- 50 Serial Remote Device Wiring Overview
- 51 X1 Addresable Device Circuit(s)
- 52 X1 Addressable Device Wiring Diagrams
- 54 PROGRAMMING THE CONTROL UNIT
- 54 KEYPAD PROGRAMMING
- 54 PC PROGRAMMING
- 54 PROGRAMMING SECURITY
- 55 MAINTENANCE
- 55 GENERAL
- 56 QUICK TEST
- 57 APPENDIX-A: REFERENCE DATA
- 57 WIRE SELECTION GUIDES
- 57 Resistance of Solid Copper Wire
- 57 Notification Appliance Circuit Wire Selection Guide
- 57 Maximum Wire Loop Distance (Feet)
- 58 Addressable Device Circuit Wire Selection Guide
- 58 Line Resistance Graph
- 59 BATTERY SIZE CALCULATIONS
- 59 MPC-6000 Current Calculations
- 59 RND-2 Current Calculations
- 59 MPC-7000 Current Calculation
- 61 Auxiliary Module Battery Calculations
- 61 Device Current Calculations
- 62 Total System Currents
- 62 Battery Size
- 63 APPENDIX-B: COMPATIBLE DEVICES
- 63 DEVICES FOR ADDRESSABLE DEVICE CIRCUITS
- 63 Faraday X1 Manual Pull Stations
- 63 Faraday X1 Modules
- 63 Faraday X1 Photo Electric Detectors
- 63 Faraday X1 Bases
- 63 Faraday X1 Accessories
- 64 DEVICES FOR NOTIFICATION APPLIANCE CIRCUITS
- 64 Notification Appliances
- 67 Accessory Devices
- 67 DEVICES FOR AUXILIARY POWER OUTPUTS
- 67 Door Holders
- 67 Relays
- 68 APPENDIX-C: TROUBLESHOOTING
- 68 DEFINITIONS FOR EVENT HISTORY ENTRIES
- 68 A. General
- 69 B. System Troubles
- 70 C. System Events
- 71 APPENDIX-D: MODULE INSTALLATION INSTRUCTIONS LIST
- 72 APPENDIX-E: GLOSSARY