advertisement
![Install the Boundary Wire. Petsafe In-Ground Fence System | Manualzz Install the Boundary Wire. Petsafe In-Ground Fence System | Manualzz](http://s1.manualzz.com/store/data/006818269_1-14e4f8f2f3db248a4877c6cb68d8691d-360x466.png)
Step
7
Install the Boundary Wire
To Bury the Boundary Wire
Burying the Boundary Wire is recommended to protect it and prevent disabling the system.
1. Cut a trench
1-3 inches
deep along your planned boundary.
2. Place the Boundary Wire into the trench maintaining some slack to allow it to expand and contract with temperature variations.
3. Use a blunt tool such as a wooden paint stick to push the Boundary Wire into the trench. Be careful not to damage the Boundary Wire.
To Attach the Boundary Wire to an Existing Fence
The Boundary Wire of the PetSafe ® In-Ground Radio Fence ™ can be attached to a chain link fence, split rail fence, or a wooden privacy fence. The Boundary Wire can be attached as high as needed. However, make sure the
Boundary Width is set at a high enough range for the pet to receive the signal. If using a Double Loop with an existing fence at least three feet tall, run the Boundary Wire on top of the fence and return it on the bottom of the fence to get the three to fi ve foot separation needed.
• Chain Link Fence (7A):
Weave Boundary Wire through the links or use plastic quick ties.
• Wooden Split Rail or Privacy Fence (7A):
Use staples to attach Boundary Wire. Avoid puncturing the insulation of the Boundary Wire.
• Double Loop with an Existing Fence:
Run the Boundary Wire on top of the fence and return it on the bottom of the fence to get the three to fi ve foot separation needed.
•
Gate (Single Loop) (7B):
Bury the Boundary Wire in the ground across the gate opening.
Note: The signal is still active across the gate. Your pet cannot pass through an open gate.
•
Gate (Double Loop) (7B):
Bury both Boundary Wires across the gate opening while keeping them
three to fi ve feet
apart.
7A 7B
WEAVE WIRE INTO FENCE
SINGLE LOOP
S TAPLE WIRE TO FENCE
S TAPLE WIRE
TO FENCE
3 ' -5 '
DOUBLE LOOP
3 ' -5 ' www.petsafe.net
11
advertisement
Related manuals
advertisement
Table of contents
- 3 Components
- 3 Other Items You May Need
- 4 Key Defi nitions
- 5 Locate the Fence Transmitter
- 5 Lay Out the System
- 6 Sample L ayouts
- 7 Position the Boundary Wire
- 8 Connect the Wires to the Fence Transmitter
- 10 Set the Boundary Width and Test the Receiver Collar
- 11 Install the Boundary Wire
- 12 Place the Boundary Flags
- 12 Fit the Receiver Collar
- 14 Be Patient With Your Pet
- 14 Day 1 - Boundary Flag Awareness
- 15 Days 2 thru 4 - Continue Boundary Flag Awareness
- 15 Days 5 thru 8 - Distraction Phase
- 16 Days 9 thru 14 - Unleashed Supervision
- 16 Days 15 thru 30 - Pet Monitoring
- 16 Taking Your Pet Out of the Pet Area
- 17 Accessories
- 18 Troubleshooting
- 19 Short Loop Test
- 20 To Locate a Break in the Boundary Wire
- 20 Terms of Use and Limitation of Liability
- 21 Caution
- 21 Product Warranty
- 64 Layout Gr id
- 64 Mounting Template
- 23 Composants
- 23 Autres éléments pouvant s’avérer nécessaires
- 24 Défi nitions
- 25 Emplacement de l’émetteur de clôture
- 25 Schéma du système
- 26 Exemples de schémas
- 28 Branchement des fi ls à l’émetteur de clôture
- 31 Installation du fi l p ériphérique
- 32 Ajustement du collier récepteur
- 34 Soyez patient avec votre animal
- 34 Jour 1 – Familiarisation avec les fanions de délimitation
- 35 Jours 2 à 4 – Familiarisation avec les fanions de délimitation (suite)
- 35 Jours 5 à 8 – Phase de distraction
- 36 Jours 9 à 14 – Supervision sans laisse
- 36 Jours 15 à 30 – Observation de l’animal
- 36 Pour sortir votre animal de la zone autorisée
- 37 Accessoires
- 38 Dépannage
- 39 Test en boucle courte
- 40 Repérage des ruptures de fi l
- 40 Conditions d’utilisation et limite de responsabilité
- 41 Mise en garde
- 41 Garantie du produit
- 64 Grille de schéma
- 64 Gabarit de montage
- 43 Componentes
- 43 Otras herramientas que puede necesitar
- 44 Defi niciones im portantes
- 45 Localice el transmisor de cerca
- 45 Prepare el sistema
- 46 Ejemplos de diseños
- 47 Coloque el cable delimitador
- 48 Conecte los cables al transmisor de cerca
- 49 Establezca la amplitud de límites y pruebe el collar receptor
- 51 Instale el cable delimitador
- 52 Coloque las banderas delimitadoras
- 52 Ajuste el collar receptor
- 54 Tenga paciencia con su mascota
- 54 Día 1: conciencia de las banderas delimitadoras
- 55 Días 2 a 4: conciencia de las banderas delimitadoras (continuación)
- 55 Días 5 a 8: etapa de distracción
- 56 Días 9 a 14: supervisión libre
- 56 Días 15 a 30: observación de la mascota
- 56 Saque a la mascota de su área
- 57 Accesorios
- 58 Resolución de problemas
- 59 Prueba de circuito corto
- 60 Para encontrar una separación en el cable delimitador
- 60 Términos de uso y limitación de responsabilidad
- 61 Precaución
- 61 Garantía del producto
- 64 Rejilla de diseño
- 64 Plantilla de instalación