advertisement
Connecting your TV
Note: Cables are not supplied with your TV.
Coaxial cable is the cable that comes in from your antenna, cable TV service, or cable converter box. Coaxial cable uses “F” connectors.
Standard stereo A/V cables usually come in sets of three, and are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. Your TV’s standard A/V inputs are color-coded in the same manner as the cables.
S-Video cable is for use with video equipment that has S-Video connectors.
Component video cables come in sets of three (typically color-coded green, blue, and red), and are for use with video equipment that has component video connectors. Your TV’s
ColorStream ® (component video) inputs are color-coded yellow, blue, and red. Plug the green component video cable into the yellow VIDEO-2 input (see “Back of TV” on page 6).
NOTE REGARDING PICTURE QUALITY
When connecting video equipment to your Toshiba TV:
For GOOD picture quality: Use a standard yellow video cable.
For BETTER picture quality: If your equipment has S-video connectors, use an
S-video cable instead of a standard yellow video cable. You still must connect the standard red and white audio cables for full system connection, but do not connect a standard yellow video cable at the same time or the picture performance will be unacceptable.
For BEST picture quality: If your equipment has component video connectors, use component video cables instead of a standard yellow video cable or S-video cable. You still must connect the standard red and white audio cables for full system connection.
Coaxial (antenna) cable
Standard stereo A/V cables
(typically color-coded yellow for video, red and white for audio)
S-video cable
Component video cables
(typically color-coded red, green, blue)
CAUTION: Do not plug in any power cords until you have finished connecting all equipment.
Connecting a VCR
With this connection you can:
• watch local TV channels and videotapes
• record one channel while watching the same or another channel
You will need:
• two coaxial cables
• one set of standard A/V cables (If your VCR has
S-video, you can use an S-video cable instead of the standard video cable. See “Note Regarding Picture
Quality” above.)
Note:
If you have a mono VCR, connect L/Mono to VCR Audio OUT using only one audio cable.
The VIDEO-2 inputs on the back of the TV can be used for connecting a second piece of video equipment such as a DVD player. The VIDEO-3 inputs* on the front of the TV can be used for connecting a third piece of video equipment such as a camcorder. See “Note Regarding Picture Quality” above.
________
*Model 32A33 does not have VIDEO 3 inputs.
From cable or antenna
Stereo VCR
S-VIDEO VIDEO
L
OUT
R
IN
OUT
IN from ANT OUT to TV
CH3
CH4
TV
VIDEO
L/
MONO
S-VIDEO
AUDIO
IN
VIDEO
Y
COLOR
STREAM
INPUT
L
AUDIO PB
R
VIDEO-1 VIDEO-2
R
PR
OUT
VIDEO
ANT
L/
MONO
AUDIO
R
Connecting a cable converter box
With this connection you can:
• watch basic and premium cable channels
Tune the TV to channel 3 or 4 (whichever channel is vacant in your area), and then use the cable converter box to change channels.
You will need:
• two coaxial cables
Note:
When you use a cable converter box with your TV, you may not be able to use the remote control to program certain features
(for example, blocking channels).
From cable
IN OUT
Cable converter box
TV
VIDEO
L/
MONO
S-VIDEO
AUDIO
IN
VIDEO
Y
COLOR
STREAM
INPUT
L
AUDIO PB
R
VIDEO-1 VIDEO-2
R
PR
OUT
VIDEO
ANT
L/
MONO
AUDIO
R
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.
7
advertisement
Related manuals
advertisement
Table of contents
- 4 Important safety information
- 6 Introduction
- 6 Exploring your new TV
- 6 Selecting a location for your TV
- 7 Connecting your TV
- 7 Connecting a VCR
- 7 Connecting a cable converter box
- 8 Connecting a cable converter box and a VCR
- 8 Connecting a satellite receiver and a VCR
- 9 (component video) and a VCR
- 9 Connecting two VCRs
- 10 Using the remote control
- 10 Preparing the remote control for use
- 10 Installing the remote control batteries
- 11 Location of controls on TV and remote control
- 12 DVD player, or HTIB (home theater in a box)
- 13 Remote control codes
- 14 DVD player, or HTIB (home theater in a box)
- 15 Setting up your TV
- 15 Menu system (general instructions)
- 16 Changing the on-screen display language
- 16 Selecting the signal source
- 16 Programming channels into the TV’s memory
- 16 Programming channels automatically
- 17 Adding and erasing channels manually
- 17 Changing channels
- 18 Using the TV’s features
- 18 Adjusting the channel settings
- 18 Switching between two channels
- 18 Programming your favorite channels
- 19 Using the V-Chip Control (blocking) feature
- 19 Selecting a PIN code
- 20 Changing your PIN code
- 21 Blocking programs by ratings
- 21 Ratings definitions (MPAA, Youth TV, TV)
- 22 Unblocking programs temporarily
- 23 Blocking unrated movies and programs
- 24 Blocking channels
- 25 Adjusting the picture
- 25 Adjusting the picture quality
- 25 Selecting the color temperature
- 26 Selecting the picture preference
- 26 Displaying on-screen information
- 26 Setting the off timer
- 26 Auto power off
- 27 Using the closed caption feature
- 28 Adjusting the sound
- 28 Muting the sound
- 28 Selecting stereo/SAP broadcasts
- 29 Adjusting the sound quality
- 29 Using the surround sound feature
- 30 Viewing the demonstration (DEMO) mode
- 30 Understanding the last mode memory feature
- 31 Appendix
- 31 Specifications
- 32 Troubleshooting
- 33 Limited United States warranty
- 34 Limited Canada warranty