DVD player, or HTIB (home theater in a box). Toshiba COLOR TELEVISION, 32A33, 32A43, 36A43
Add to My manuals36 Pages
advertisement
Programming the remote control to operate a cable converter box, satellite receiver, VCR, DVD player, or HTIB (home theater in a box)
Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 14.
}
RECALL
POWER
Channel
Numbers
Device Switch
1
In the remote control code table (below and on the next page), find the code for your device. If more than one code is listed, try each one separately until you find one that works.
2
Set the Device Switch to the type of device you are programming the remote control to operate— CBL/SAT (for a cable converter box or satellite receiver), VCR (for a VCR or TV/VCR combo), or DVD
(for a DVD player or HTIB [home theater in a box]).
3
While holding down RECALL , press the Channel Number buttons to enter the 3-digit code for your device.
4 To test the code, turn on the device, point the remote control at it, and press POWER .
–If the correct code was entered, the device will turn off.
–If the device does not respond, repeat steps 1–4 using another code.
–If the device does not respond to another code, you will need to use the remote control that came with the device.
Note: In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.
5
Remember to set the Device Switch back to “TV” to control the TV.
6
For future reference, write down the code(s) you used:
DEVICE CODE DEVICE CODE
Note:
Each time you change the batteries, you will need to reprogram the remote control.
Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/
VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.
Remote control codes
In some cases you may not be able to operate your device with the TV remote control. Your other device may use a code that is not recognized by the TV remote control. If this happens, you will need to use the remote control provided with the device.
Cable converter box
ABC: 061, 062, 063, 082,
084, 087, 091, 092,
096, 098
Archer: 065, 092, 097, 099
Cableview: 064, 094
Century: 092
Citizen: 090, 092, 097
Contec: 083, 085, 086,
088, 093, 098
Diamond: 093
Eagle: 091
GE: 061, 062
Gemini: 069, 070, 094
General Instruments: 062,
089, 096
Hamlin: 093
Hitachi: 062, 095, 096
Jasco: 097
Jerrold: 062, 069, 071,
082, 086, 089, 091,
096
Magnavox: 072, 096
Memorex: 091, 092, 104
Multi Canal: 090
Novavision: 101
Panasonic: 081, 083, 085
Philco: 087
Philips: 066, 067, 068,
070, 072, 073, 074,
075, 091, 092
Pioneer: 076, 077
Proscan: 061, 062
Radio Shack: 092, 097,
099
RCA: 064, 081
Realistic: 065
Recoton: 102
Samsung: 077, 090
Scientific Atlanta: 063,
078, 079, 080, 088,
098, 101, 105
Sears: 095
Signature: 062
Signature 2000: 096
Sprucer: 081, 085
Starcom: 069, 082, 087,
096, 103, 104
Stargate: 069, 090
Sylvania: 095, 100
TeleView: 090
Texscan: 100
Tocom: 071, 084, 085
U. S. Electronics: 087,
096, 098
United Cable: 082
Universal: 065, 092, 097,
099, 102, 103
Wards: 096
Satellite receiver
Alphastar: 038, 059
Chaparral: 034
DISH Network: 057
Drake: 020, 040, 044, 046,
050, 053
Echostar: 018, 041, 051
Express Vu: 057
Fujitsu: 027
GE: 008, 009, 013
12
advertisement
Related manuals
advertisement
Table of contents
- 4 Important safety information
- 6 Introduction
- 6 Exploring your new TV
- 6 Selecting a location for your TV
- 7 Connecting your TV
- 7 Connecting a VCR
- 7 Connecting a cable converter box
- 8 Connecting a cable converter box and a VCR
- 8 Connecting a satellite receiver and a VCR
- 9 (component video) and a VCR
- 9 Connecting two VCRs
- 10 Using the remote control
- 10 Preparing the remote control for use
- 10 Installing the remote control batteries
- 11 Location of controls on TV and remote control
- 12 DVD player, or HTIB (home theater in a box)
- 13 Remote control codes
- 14 DVD player, or HTIB (home theater in a box)
- 15 Setting up your TV
- 15 Menu system (general instructions)
- 16 Changing the on-screen display language
- 16 Selecting the signal source
- 16 Programming channels into the TV’s memory
- 16 Programming channels automatically
- 17 Adding and erasing channels manually
- 17 Changing channels
- 18 Using the TV’s features
- 18 Adjusting the channel settings
- 18 Switching between two channels
- 18 Programming your favorite channels
- 19 Using the V-Chip Control (blocking) feature
- 19 Selecting a PIN code
- 20 Changing your PIN code
- 21 Blocking programs by ratings
- 21 Ratings definitions (MPAA, Youth TV, TV)
- 22 Unblocking programs temporarily
- 23 Blocking unrated movies and programs
- 24 Blocking channels
- 25 Adjusting the picture
- 25 Adjusting the picture quality
- 25 Selecting the color temperature
- 26 Selecting the picture preference
- 26 Displaying on-screen information
- 26 Setting the off timer
- 26 Auto power off
- 27 Using the closed caption feature
- 28 Adjusting the sound
- 28 Muting the sound
- 28 Selecting stereo/SAP broadcasts
- 29 Adjusting the sound quality
- 29 Using the surround sound feature
- 30 Viewing the demonstration (DEMO) mode
- 30 Understanding the last mode memory feature
- 31 Appendix
- 31 Specifications
- 32 Troubleshooting
- 33 Limited United States warranty
- 34 Limited Canada warranty