3 Installation. Mettler Toledo SevenGo Duo pro™ pH/ORP/Ion/Conductivity meter SG78
Add to My manuals
124 Pages
advertisement
![3 Installation. Mettler Toledo SevenGo Duo pro™ pH/ORP/Ion/Conductivity meter SG78 | Manualzz 3 Installation. Mettler Toledo SevenGo Duo pro™ pH/ORP/Ion/Conductivity meter SG78 | Manualzz](http://s1.manualzz.com/store/data/065933219_1-a73a4980f1ebdaf3664c69e7303a52b5-360x466.png)
3 Installation
Carefully unpack the meter. Keep the calibration certificate in a safe place.
3.1 Installing the batteries
NOTICE
Damage to the instrument due to the unsealed battery cover
The IP67 rating requires the battery compartment to be perfectly sealed. The sealing ring around the battery cover must be replaced if it is damaged in any way.
1 Slide the release button on the battery cover in the direction of the arrow.
2 Hold the lid with two fingers and remove it.
3 Insert the batteries in the battery compartment, as indicated by the arrows on the inside of the compartment.
4 Replace the battery cover and push back the button to fix the lid in place.
3.2 Connecting a sensor
IP67 sensors
To connect the IP67 sensors, make sure that the plugs are properly inserted. Twist the RCA (Cinch) plug to ease the attachment of the sensor.
ISM ® sensor
When connecting an ISM ® sensor to the meter, one of the following conditions have to be met for the calibration data to be transferred automatically from the chip of the sensor into the meter and is used for further measurements. After attaching the ISM ® sensor ...
The meter must be switched on.
(If the meter is already switched on) the READ key is pressed.
(If the meter is already switched on) the CAL key is pressed.
We strongly recommend you to switch off the meter when disconnecting an ISM sensor. In doing so, you make sure that the sensor is not removed while the instrument is reading data from or writing data to the ISM-chip of the sensor.
The ISM icon appears on the display and the sensor ID of the sensor chip is registered and appears on the display.
3.3 Fitting the wrist strap
Fit the wrist strap as shown in the diagram.
6 Installation SevenGo Duo pro™
3.4 SevenGo™ clip
The SevenGo™ clip is an electrode holder that can be placed next to the display on either side of the housing.
1 To mount the clip, remove the cover over the clip's fixing point using your thumbnail.
2 Attach the clip by pressing it into the recess.
3 Slide the shaft of the sensor into the clip from the top.
4 Rotate the sensor around the clip's axis to switch between the storage and working positions.
3.5 SevenGo™ two-electrode clip
The SevenGo™ two-electrode clip is the ideal accessory for handling two electrodes in the field. Two electrode clips can be connected.
Attach the two clips by pressing them into the recesses of the clip connector.
SevenGo Duo pro™ Installation 7
advertisement
Related manuals
advertisement
Table of contents
- 1 Title Page
- 3 Table of Contents
- 5 English
- 5 Table of Contents
- 7 1 Introduction
- 8 2 Safety Measures
- 8 2.1 Definitions of signal words and warning symbols
- 8 2.2 Product specific safety notes
- 10 3 Installation
- 10 3.1 Installing the batteries
- 10 3.2 Connecting a sensor
- 10 3.3 Fitting the wrist strap
- 11 3.4 SevenGo™ clip
- 11 3.5 SevenGo™ two-electrode clip
- 12 4 Operating the pH/ORP/Ion/Conductivity meter SG78
- 12 4.1 Meter layout
- 13 4.2 The display
- 14 4.3 Key controls
- 15 4.4 Using the softkeys
- 15 4.5 Navigating between menus
- 16 4.6 Navigating within a menu
- 16 4.7 Using the alphanumeric keypad
- 16 4.7.1 Alphanumeric input
- 16 4.7.2 Entering IDs/PIN
- 17 4.7.3 Editing values in a table
- 17 4.8 Calibration
- 17 4.8.1 Running a one-point pH/ion or one-point conductivity calibration
- 17 4.8.2 Running a multi-point pH/ion calibration
- 18 4.9 Automatic buffer recognition
- 18 4.10 Sample measurements
- 18 4.11 Temperature compensation
- 19 5 Setup
- 19 5.1 Menu structure of setup
- 19 5.2 Sample ID
- 19 5.3 User ID
- 19 5.4 Data logging
- 20 5.5 System settings
- 21 5.6 Instrument self-test
- 22 6 Menus and settings
- 22 6.1 Menu structure of pH/ion
- 22 6.2 Menu structure of conductivity
- 22 6.3 Temperature settings
- 22 6.4 pH/ion calibration settings
- 23 6.5 pH/ion measurement settings
- 25 6.6 Conductivity calibration settings
- 25 6.7 Conductivity measurement settings
- 26 6.8 Endpoint formats
- 27 6.9 Measurement limits
- 27 6.10 Sensor ID/SN
- 28 7 Data management
- 28 7.1 Menu structure of data menu
- 28 7.2 Measurement data
- 28 7.3 Calibration data
- 29 7.4 ISM data
- 31 8 Maintenance
- 31 8.1 Meter maintenance
- 31 8.2 Electrode maintenance
- 31 8.3 Disposal
- 31 8.4 Error messages
- 33 8.5 Error limits
- 34 9 Sensors, solutions and accessories
- 36 10 Specifications
- 38 11 Appendix
- 38 11.1 Buffer tables
- 39 11.2 Temperature correction factors
- 40 11.3 Conductivity standards table
- 41 11.4 Temperature coefficients (alpha-values)
- 41 11.5 Practical salinity scale (UNESCO 1978)
- 42 11.6 Conductivity to TDS conversion factors
- 43 Français
- 43 Table des matières
- 45 1 Introduction
- 46 2 Mesures de sécurité
- 46 2.1 Définition des termes de notification et des symboles d'avertissement
- 46 2.2 Consignes de sécurité relatives au produit
- 48 3 Installation
- 48 3.1 Installation des piles
- 48 3.2 Connecter un capteur
- 48 3.3 Montage de la dragonne
- 49 3.4 Clip SevenGo™
- 49 3.5 Clip deux électrodes SevenGo™
- 50 4 Commande de l'appareil de mesure de pH/ORP/ions/conductivité SG78
- 50 4.1 Structure de l'appareil de mesure
- 51 4.2 L'écran
- 52 4.3 Commandes de touche
- 53 4.4 Utilisation des touches programmables
- 54 4.5 Naviguer entre les menus
- 54 4.6 Naviguer dans un menu
- 54 4.7 Utilisation du clavier alphanumérique
- 54 4.7.1 Saisie alphanumérique
- 55 4.7.2 Saisie des ID/PIN
- 55 4.7.3 Editer des valeurs dans un tableau
- 55 4.8 Etalonnage
- 55 4.8.1 Exécution d'un étalonnage pH/ion à un point ou de conductivité à un point
- 56 4.8.2 Effectuer un étalonnage pH/ion multipoints
- 56 4.9 Reconnaissance automatique de tampons
- 56 4.10 Mesures d'échantillon
- 57 4.11 Compensation de température
- 58 5 Configuration
- 58 5.1 Structure du menu de configuration
- 58 5.2 ID échantillon
- 58 5.3 Nom utilisateur
- 58 5.4 Enregistrement des données
- 59 5.5 Paramètres système
- 60 5.6 Test automatique de l'appareil
- 61 6 Menus et paramètres
- 61 6.1 Structure de menu pH/ion
- 61 6.2 Structure du menu de conductivité
- 61 6.3 Paramètres de température
- 61 6.4 Paramètres d'étalonnage pH/ion
- 62 6.5 Paramètres de mesurage pH/ion
- 64 6.6 Paramètres d'étalonnage de conductivité
- 64 6.7 Paramètres de mesure de conductivité
- 65 6.8 Formats du point final
- 66 6.9 Définir les limites
- 66 6.10 ID/SN de capteur
- 67 7 Gestion des données
- 67 7.1 Structure du menu de données
- 67 7.2 Données de mesure
- 68 7.3 Données d'étalonnage
- 68 7.4 Données ISM
- 70 8 Maintenance
- 70 8.1 Maintenance de l'appareil de mesure
- 70 8.2 Maintenance de l'électrode
- 70 8.3 Mise au rebut
- 70 8.4 Messages d’erreur
- 72 8.5 Limites d'erreur
- 74 9 Capteurs, solutions et accessoires
- 76 10 Spécifications
- 78 11 Annexe
- 78 11.1 Table des tampons
- 79 11.2 Facteurs de correction de température
- 80 11.3 Table des étalons de conductivité
- 81 11.4 Coefficients de température (valeurs alpha)
- 81 11.5 Echelle de salinité pratique (UNESCO 1978)
- 82 11.6 Conductivité en fonction des facteurs de conversion TDS
- 83 Español
- 83 Índice de contenidos
- 85 1 Introducción
- 86 2 Medidas de seguridad
- 86 2.1 Definiciones de los textos y símbolos de advertencia
- 86 2.2 Indicaciones de seguridad específicas del producto
- 88 3 Instalación
- 88 3.1 Colocación de las pilas
- 88 3.2 Conexión del sensor
- 88 3.3 Como ajustar la correa muñequera
- 89 3.4 Pinza SevenGo™
- 89 3.5 Clip para dos electrodos SevenGo™
- 90 4 Funcionamiento del medidor de pH/ORP/Ion/Conductividad SG78
- 90 4.1 Esquema del medidor
- 91 4.2 La pantalla
- 92 4.3 Controles de las teclas
- 93 4.4 Utilización de las teclas de función
- 94 4.5 Navegar por los menús
- 94 4.6 Navegación dentro de un menú
- 94 4.7 Uso del teclado alfanumérico
- 94 4.7.1 Entrada alfanumérica
- 95 4.7.2 Introducción de ID o números PIN
- 95 4.7.3 Editar valores en una tabla
- 95 4.8 Calibración
- 95 4.8.1 Realización de calibración de pH/ion a un punto o calibración de conductividad a un punto
- 96 4.8.2 Realización de una calibración de pH/ion multipunto
- 96 4.9 Reconocimiento automático del estándar
- 96 4.10 Medidas de muestra
- 97 4.11 Compensación de temperatura
- 98 5 Instalación
- 98 5.1 Estructura del menú de instalación
- 98 5.2 ID de la muestra
- 98 5.3 ID usuario
- 98 5.4 Registro de datos
- 99 5.5 Puesta a punto del sistema
- 100 5.6 Autocomprobación del equipo
- 101 6 Menús y configuraciones
- 101 6.1 Estructura del menú de pH/ion
- 101 6.2 Estructura del menú de conductividad
- 101 6.3 Configuración de temperatura
- 101 6.4 Configuración de la calibración de pH/ion
- 102 6.5 Configuración de medición de pH/ion
- 104 6.6 Configuración de la calibración de conductividad
- 104 6.7 Configuración de medición de la conductividad
- 105 6.8 Formatos de punto final
- 106 6.9 Límites de medición
- 106 6.10 ID/SN Sensor
- 107 7 Administración de datos
- 107 7.1 Estructura del menú de datos
- 107 7.2 Datos de medición
- 108 7.3 Datos de calibración
- 108 7.4 Datos ISM
- 110 8 Conservación
- 110 8.1 Mantenimiento del medidor
- 110 8.2 Mantenimiento de electrodos
- 110 8.3 Eliminación
- 110 8.4 Mensajes de error
- 112 8.5 Límites de error
- 114 9 Sensores, soluciones y accesorios
- 116 10 Especificaciones
- 118 11 Apéndice
- 118 11.1 Tablas de los tampones
- 119 11.2 Factores de corrección de temperatura
- 120 11.3 Tabla de estándares de conductividad
- 121 11.4 Coeficientes de temperatura (valores alfa)
- 121 11.5 Escala práctica de salinidad (UNESCO, 1978)
- 122 11.6 Conductividad con factores de conversión TDS